Summary of Contents for Easy CDV43
- Page 1 CDV43 USER MANUAL(EN) 2-Wire Video Intercom System Read this manual carefully before using the product, keep for future use. in a safe place...
-
Page 2: Code
1.Parts and Functions Microphone LCD Screen Mounting Hook RING Connection Port Close Button Mute Button/Indicator Menu Button Return Button Up Button Down Button Talk/Mon Button Unlock Button Terminal Description SW+,SW-: Door bell call button connection port. Ring,GND: Extra buzzer connection port. -
Page 3: Main Menu
Use the screws provided to fix the Mounting Bracket (fits a standard UK single gang flush back box if required). Fitting accessories includes a Bracket (Two x M4 x 25mm screws are needed for fastening the Mounting Bracket), 1 x green connector to connect the bus line to the Monitor) Wire the system correctly (please refer to the connection chapter) then fit the Monitor to the Mounting Bracket firmly. -
Page 4: Code
5. Intercom Function When the monitor is in standby mode, press ' Menu b utton to enter main menu page. Use button to move up/down to select 'Intercom Call' , press ' Menu' b utton to enter the 'S elect I ntercom ' page, there are 3 options available . -
Page 5: Do Not Disturb Function
6. Divert Call Function ( Requ ire s CDV-GSM ) Menu Button to enter main menu page. When the monitor is in standby mode, press b utton to move upward / downward to select Divert Call item, press Menu Button to enter the call divert options page, you have 4 items to select. Main Menu Call Divert Options Monitor By Select... - Page 6 8. Light Function (Requires CDV-RLC) When the monitor is in standby mode, press Menu Button to enter main menu page. Button to move upward / downward to select 'Light' option , press Menu Button to enter the 'Light' Option page, there are 3 options. Main Menu Light Option Light...
-
Page 7: Code
10. Restore to Default When the monitor is in standby mode, press Menu button to enter main menu page. button to move upward / downward to select Restore option , press Menu button to enter the restore page, then press Menu button to confirm. -
Page 8: Code
11.4 How to set the slave monitor address Maximum of 4 monitors can be connected in one apartment, one master monitor together with 3 slave monitors, addresses must be the same.(note: must have one monitor to be set as master monitor) Code 8000 is used to set the master monitor. -
Page 9: Code
11.7 How to enable/disable auto unlocking (Disabled by default). Function Description: Auto unlocking allows the door to unlock after 5 seconds of a placed call from the door station without the need to answer or unlock the door, this allows the user to 'leave the door on the latch' for a known visitor . -
Page 10: Table Of Contents
Bit-6 line terminal setting: Bit state Setting Bit state Setting ON(1) OFF(0) Monitor not at Monitor at the end of the the end of line. the line. Bit state User Code Bit state User Code Bit state User Code Code=1 Code=12 Code=23 Code=2... -
Page 11: Basic Connection
12. Basic Connection door station BUS(IM) BUS(DS) Doorbell Button NC GND RING sw- sw+ Switch 13.Screen and Volume Adjustment During monitoring or a call press Menu button, the Adjustment menu will be displayed. / button to increase/decrease the Use the Menu to select the option required, use value, press the Return button to quit the adjust page . -
Page 12: Specifications
14. Specifications ●● Power●supply●for●indoor●monitor:●● ● DC●20~28V● ●● Power●consumption:● ●● Standby●0.17W;●Working●status●4.7W ●● Monitor●screen:● ● 4.3●inch●digital●color●TFT ●● Display●Resolutions:● ● 480(R,●G,●B)●x●272●pixels ●● Video●signal:● ● 1Vp-p,●75Ω,●CCIR●standard ●● Wiring:● ● 2●wires,●non-polarity ●● Monitor●time:● ● 40●seconds ●● Talking●time:● ● 90●seconds ●● Dimensions:● ● 137(H)×137(W)×17(D)mm The design and specifications can be changed without notice to the user. Right to interpret and copyright of this manual are preserved.