Table of Contents
Advertisement
MAINTENANCE
TRACTOR
Always observe safety rules when performing any main-
tenance.
BRAKE
OPERATION
if tractor requires more than six (6) feet stopping distance
at high speed in highest gear, then brake must be adjusted.
(See "TO ADJUST BRAKE" in the Service and Adjustments
section of this manual).
TIRES
Maintain proper airpressure in all tires (See "PRODUCT
SPECIFICATIONS" section of this manual).
•
Keep tires free of gasotine, oil, or insect control chemi-
cals which can harm rubber.
Avoid stumps, stones, deep ruts, sharp objects and
other hazards that may cause tire damage.
NOTE: To seal tire punctures and prevent flat tires due to
slow leaks, tire sealant may be purchased from your local
parts dealer. Tire sealant also prevents tire dry rot and
corrosion.
OPERATOR
PRESENCE
SYSTEM
Be sure operator presence and interlock systems are work-
ing properly. If your tractor does not function as described,
repair the problem immediately.
•
The engine should not start unless the brake pedal is
fully depressed and attachement clutch control is in
the disengaged position.
•
When the engine is running, anyattempt bythe operator
to leave the seat without first setting the parking brake
should shut off the engine.
•
When the engine is running and the attachment clutch
is engaged, any attempt by the operator to leave the
seat should shut off the engine.
•
The attachment
clutch should never operate unless
the operator is in the seat.
BLADE
CARE
For best results mower blades must be kept sharp. Replace
bent or damaged blades.
BLADE
REMOVAL
(See Fig. 10)
•
Raise mower to highest position to allow access to
blades.
•
Remove blade bolt, Iockwasher and flatwasher secudng
blade.
•
Install new or resharpened blade with trailing edge up
towards deck as shown.
IMPORTANT:
TO ENSURE
PROPER ASSEMBLY, CENTER
HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL
ASSEMBLY.
•
Reassemble
blade bolt, lock washer and flat washer
in exact order as shown.
•
Tighten blade bolt securely (27-35 Ft. Lbs. torque).
IMPORTANT:
BLADE BOLT IS GRADE 8 HEAT TREATED.
TRAILING EDGE UP
BLADE
CENTER
HOLE
,MANDREL
ASSEMBLY
16
FLATWASHEE
LOCKWASHER_f-,_
STAB
(_..-_BLADEBOLT
*A GRADE 8 HEATTREATED
BOLT CAN BE
IDENTIRED
BY SIX LINES ONTHE BOLT HEAD,
FIG. 10
TO SHARPEN
BLADE (See Fig. 11)
NOTE: We do not recommend sharpening blade - but if
you do, be sure the blade is balanced.
Care should be taken to keep the blade balanced. An un-
balanced blade will cause excessive vibration and eventual
damage to mower and engine.
•
The blade can be sharpened with a file or on a grind-
ing wheel.
Do not attempt to sharpen while on the
mower.
•
To check blade balance, you will need a 5/8" diameter
steel belt, pin, or a cone balancer.
(When using a
cone balancer, follow the instructions supplied with
balancer).
NOTE: Do not use a nail for balancing blade. The lobes of
the center hole may appear to be centered, but are not.
•
Slide blade on to an unthreaded portion of the steel bolt
or pin and hold the bolt or pin parallel with the ground.
If blade is balanced
it should remain in a horizontal
position. If either end of the blade moves downward,
sharpen the heavy end until the blade is balanced.
5/8" BOLT__
_/
BLADE
OR PIN _
FIG. 11
BATTERY
Yourtractorhas a battery chargingsystem which is sufficient
for normal use, However, periodic charging of the battery
with an automotive charger will extend its life.
Keep battery and terminals clean.
•
Keep battery bolts tight.
•
Keep small vent holes open.
•
Recharge at 6-10 amperes for I hour.
NOTE: The original equipment battery on your tractor is
maintenance free. Do not attempt to open or remove caps
or covers. Adding or checking level of electrolyte is not
necessary.
Hide quick links:
Advertisement
Table of Contents
Troubleshooting
