Wi-Fi Connection - Nexaria NEX-SH-B109 Instructlon Manual

2(ii). Ethernet connection: 2(ii). Ethernet connection:
a. Insert one end of an Ethernet cable into the LAN Port on the back panel of the router. Insert a. Insert one end of an Ethernet cable into the LAN Port on the back panel of the router. Insert
the other end into an available Ethernet port of the network adapter in the computer that will the other end into an available Ethernet port of the network adapter in the computer that will
be used to configure the unit. be used to configure the unit.
b. LAN LED should be on when connected. If not, check the connection between the router b. LAN LED should be on when connected. If not, check the connection between the router
and computer. and computer.
NOTE: The Business Class II High Availability Router LAN Port is "Auto-MDI/MDIX", so NOTE: The Business Class II High Availability Router LAN Port is "Auto-MDI/MDIX", so
any standard Ethernet cable will work. any standard Ethernet cable will work.
3. Power connection. 3. Power connection.
a. Connect the power adapter to the receptor on the back a. Connect the power adapter to the receptor on the back
panel of the router. Plug the other end of the power panel of the router. Plug the other end of the power
adapter into a wall outlet or power strip. adapter into a wall outlet or power strip.
b. The 3G & Wi-Fi LED will turn ON and flash, b. The 3G & Wi-Fi LED will turn ON and flash,
indicating that the unit is powered on. Also performing indicating that the unit is powered on. Also performing
the boot-up cycle. The LAN and WAN lights will the boot-up cycle. The LAN and WAN lights will
be on if connected. be on if connected.
c. The 3G/4G LED will flash and stabilize once a 3G/4G c. The 3G/4G LED will flash and stabilize once a 3G/4G
connection is established. connection is established.
d. Upon completion of the boot-up cycle, the 3G light, LAN and Wi-Fi lights will be on. d. Upon completion of the boot-up cycle, the 3G light, LAN and Wi-Fi lights will be on.
Occational flashing may occur indicating normal activity. Occational flashing may occur indicating normal activity.
NOTES: An uninterruptable power supply (UPS) is recommended for power surges and/or NOTES: An uninterruptable power supply (UPS) is recommended for power surges and/or
outages. At a minimum, a surge protector should always be used to protect the outages. At a minimum, a surge protector should always be used to protect the
equipment from being damaged by electrical spikes and transients. equipment from being damaged by electrical spikes and transients.

Wi-Fi Connection

Wi-Fi Connection
If you are connecting wirelessly to the Business Class II High Availability Router, you must If you are connecting wirelessly to the Business Class II High Availability Router, you must
ensure that the security settings on the connecting PC are the same as those on the router. ensure that the security settings on the connecting PC are the same as those on the router.
By default, the router broadcasts a secure Wi-Fi signal with WPA-PSK* encryption: By default, the router broadcasts a secure Wi-Fi signal with WPA-PSK* encryption:
• SSID / Wi-Fi Signal Name is set to NEXWARE### (where ### equal the last three • SSID / Wi-Fi Signal Name is set to NEXWARE### (where ### equal the last three
characters of the router's MAC address) characters of the router's MAC address)
• Channel is set to channel 5(2.4GHz) • Channel is set to channel 5(2.4GHz)
• Security is set to WPA-PSK* • Security is set to WPA-PSK*
• Key (password) is set to password • Key (password) is set to password
NOTE: It is recommended, for security reasons, that the security settings on the router be NOTE: It is recommended, for security reasons, that the security settings on the router be
changed during initial setup. changed during initial setup.
*Please refer to your computer's Wi-Fi adapter documentation for additional information. *Please refer to your computer's Wi-Fi adapter documentation for additional information.