To Replace Motion Drive Belt; Transaxle Motion Control Lever Neutral Adjustment; To Check Brake; To Adjust Brake - Poulan Pro LAWN TRACTOR PO17H42STA Owner's Manual

SERVICE AND ADJUSTMENTS
TO CHECK BRAKE
• Park tractor on a level, dry concrete or paved surface,
depress clutch/brake pedal all the way down and en-
gage parking brake.
• Disengage transmission by placing freewhel control
in "transmission disengaged" position. Pull freewheel
control out and into the slot and release so it is held in
the disengaged position.
The rear wheels mustlock and skidwhen you tryto manually
push the tractor forward. If the rear wheels rotate, the brake
needs to be adjusted Or the pads need to be replaced.
TO ADJUST BRAKE
• Depress clutch/brake pedal all the way down and en-
gage parking brake.
• Measure distance between brake operating arm and
nut "A" on brake rod.
• If distance is other than 1-9/16", loosen jam nut and
turn nut"A" untildistance becomes 1-9/16". Retighten
jam nut against nut "A'.
• Engage transmission by placing freewheel control in
=transmission engaged" position.
• Road test tractor for proper stopping distance as stated
above. Readjust if necessary. If stopping distance is
still greater than five (5) feet in highest gear, further
maintenance is necessary. Replace brake pads or
contact a qualified service center.
WITH PARKING BRAKE "ENGAGED"
NUT "A"
ARM
DO NOTTOUCHTHIS NUT. IF FURTHER
BRAKE ADJUSTMENT IS NECESSARY CON-
TACTYOUR NEAREST AUTHORIZED SERVICE
CENTER/DEPARTMENT
FIG. 22
TO REPLACE MOTION DRIVE BELT
(See Fig. 23)
Park the tractor on level surface. Engage parking brake.
For assistance, there is a belt installation guide decal on
bottom side of left footrest.
BELT REMOVAL -
• Remove mower (See "TO REMOVE MOWER" in this
section of manual).
NOTE: Observe entire motion drive belt and position of a!l
belt guides and keepers.
• Remove belt from stationary idler and clutching idler.
• Remove belt downward from around engine pulley.
21
• Pull belt slack toward rear of tractor. Carefully remove
belt upwards from transmission input pulley and over
cooling fan blades.
• Remove belt from center span keeper and pull belt
away from tractor.
BELT INSTALLATION -
Carefully work new belt down around transmission
cooling fan and onto the input pulley.
• Slide belt into the center span keeper.
• Pull belt toward front of tractor and roll around the top
groove of engine pulley.
• Install belt through stationary idler and clutching
idler.
• Make sure belt is in all pulley grooves and inside all
belt guides and keepers.
• Install mower (See"TO INSTALL MOWER" in this sec-
tion of manual).
ENGINE
PULLEY _
_
CLUTCHING _ --_ I _
,OLER
STAT,ONA+ --
IDLER l_
TRANSMISSION
INPUT PULLEY _ .J_/:-__,
FIG. 23
\
CENTER SPAN
KEEPER
0
TRANSAXLE MOTION CONTROL LEVER
NEUTRAL ADJUSTMENT (See Fig. 24)
The motion control lever has been preset at the factory and
adjustment should not be necessary.
• Loosen adjustment belt in front of the right rear wheel,
and lightly tighten.
• Start engine and move motion control lever until tractor
does not move forward or backward.
• Hold motion control lever inthat positionand turn engine
off.
While holding motion control lever in place, loosen the
adjustment belt.
• Move motion control lever to the neutral (N) (lock gate)
position.
• Tighten adjustment bolt securely.
NOTE: Ifadditionalclearance is needed to get toadjustment
bolt, move mower deck height to the lowest position.
After above adjustment is made, if the tractor still creeps
forward or backward while motion control lever is in neutral
position, follow these steps:
• Loosen the adjustment bolt.
• Move the motion control lever 1/4 to 1/2 inch in the
direction it is trying to creep.
• Tighten adjustment bolt securely.
• Start engine and test.
• If tractor still creeps, repeat above steps until satis-
fied.