1. Manuals
  2. Brands
  3. Faytech Manuals
  4. Touch Panel
  5. FT10TM
  6. Manual

Faytech FT10TM Manual

Non-wifi touch screen
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Non-Wifi Touch Screen
FT10TM

Advertisement

Table of Contents
loading

Related Manuals for Faytech FT10TM

Summary of Contents for Faytech FT10TM

  • Page 1 Non-Wifi Touch Screen FT10TM...

  • Page 2: Table Of Contents

    USB port........................10 Display Operation......................11 The remote control ....................11 OSD-Menu-Operation ....................11 Installation of the Touch-Driver under Windows .............. 12 Setting up the faytech Touch software................16 Troubleshooting........................ 23 Physical Setup: ......................23 Startup:........................23 Technical Data ......................... 25 Timing-Parameter and supported VGA-resolution............
  • Page 3 Kontakt / Contact......................28...

  • Page 4: Warranty

    If it is found that faytech's Product has been returned without cause and is still serviceable, Customer will be notified and the Product returned at Customer's expense.
  • Page 5 If your device does have a defect within the warranty period, please contact faytech directly. The warranty period is 24 months from the date of purchase under the following conditions: All warranties are void if the unit has been opened or disassembled without faytech's prior approval.

  • Page 6: General Warning

    ONGOING CHANGES: faytech produces its displays in China with German know-how and quality management. Your feedback is the most valuable information for the improvement of our products. Continuous production and product improvement is our primary goal. For this reason, there may be improvements in our products which are not yet included in this user's guide.

  • Page 7: Components

    COMPONENTS: 1. USB-Port 2. Ear-out 3. Loudspeaker 4. (+): flips picture horizontally, once OSD opened increases volume or values, navigates through OSD menu to the RIGHT. 5. (-): opens volume-menu, decreases volume and marked values in OSD menu, navigates through OSD menu to the LEFT. 6.
  • Page 8 24 25 17. Power Supply 18. 12 V Adaptor 19. VGA-Audio-In 20. Video- and Audio-In adaptor 21. VGA-In 22. HDMI-In 23. 8-36V DC-I, 5.5mm/2.5mm (+) 24. USB-B In for Touch- and USB HUB Function 25. Serial-In for Serial Touch function 26.

  • Page 9: Display Connection

    TO CONNECT THE SIGNAL SOURCE, you have the following options: On a PC: Connect the VGA cable from the faytech monitor to the VGA output of your PC graphics card. Please select SOURCE VGA, so you have an image on the display.

  • Page 10: Connect To Power

    CONNECT TO POWER You can connect the faytech display with the included 100V/240V plug or the 12V power adapter. Insert one of these power sources into the 12V DC-IN. Another alternative is to connect another 12V source to the DC-IN. Please pay attention not to mix the polarity (+ is inside)! Please make secure that the power source has enough current, at 12V it is max.

  • Page 11: Display Operation

    OSD-MENU-OPERATION The Menu operation of the faytech display is simple and logical. You have six control buttons. MENU, +/right, -/left, down(c), up(b), confirm(S). Pressing MENU brings up the OSD menu and closes it again with another press, in sub menus you go back one step by pressing MENU.

  • Page 12: Installation Of The Touch-Driver Under Windows

    INSTALLATION OF THE TOUCH-DRIVER UNDER WINDOWS faytech´s own 4/5-wire USB/serial TouchController series based on EETIs MER4485 chipset supports the gesture control of Win7 and Win8 as well as the use of the touch already within the LogIn window without further driver installation. We suggest to not install any additional drivers under Win7 or Win8 operation system.
  • Page 13 For calibration purpose we suggest to install the calibration tool „Win7,Win8_calibration_TOOL“ which is available on faytech´s Driver DVD or at www.faytech.com, Service, Driver. For Win7, Win8 please just install the available drivers when you want to use Touch without the gestures support as sole mouse alternative.
  • Page 14 “Next system boot up” a calibration will be performed on the next system reboot. You can carry out a calibration at any time after the TouchKit program is installed. (See “Setting up the faytech Touch software”.) After making your selection on this screen, click “Next”. 6."TouchKit - InstallShield Wizard": Connect the USB cable now and press "OK".
  • Page 15 7. "Setup Type": If you plan to use multiple monitors, please choose this box. (See “Setting up the faytech Touch software”.) 8."Choose Destination Location": Accept the default destination or choose your own then press "Next". 9. "Select Program Folder": Give the program a name or use the default setting and press "Next".

  • Page 16: Setting Up The Faytech Touch Software

    Under linearization, you can choose the number of linearization points under the Tools - linearization setting. On a 25-point linearization the deviation of a touched point will be less than on a 9-point linearization. In general, the faytech displays have been set correctly and should not be linearized.
  • Page 17 For a better understanding of this setting, try it with the Draw Test application under the Tools tab. On the far right of the mouse icon, there is an Option button. The following options are available for the faytech display in this submenu:...
  • Page 18 Enable Constant Touch: is the function to check to enable the driver to determine if the most recent touched position is the same as the previously touched point. If the difference is smaller than the defined area, the driver does not generate any mouse movement which helps reduce system load.
  • Page 19 You can adjust the faytech touch panel calibration with the functions called 4 Points Calibration, Clear and Calibrate, Linearization and Draw Test. Start by performing the 4 points calibration. By using the application drawing test, you can test the touch panel to determine if further setting changes are desirable.
  • Page 20 Display tab when you run the Touchkit Configure utility. If you did not select this option, you will not see a Display tab. You can have up to four faytech touch-screens connected simultaneously. You can also use a (non-touch) display and a touch screen. In the example below, the touch-screen is display "1", while the second display "2"...
  • Page 21 The Operation mode settings allow you to set the size of the touch area on your faytech touch-screen. E.g. if you select the "right screen“, after a new calibration only the right side of the monitor will work as a touch area.
  • Page 22 6. Hardware and About tabs: The last two tabs are for information only - there are no options to select on these tabs. The Hardware tab gives information about the design of the faytech touch display and the firmware used.

  • Page 23: Troubleshooting

    TROUBLESHOOTING If you are having trouble getting your touch monitor to work correctly, please look through this list of common problems: PHYSICAL SETUP: Cable connections. Care should be taken when connecting the cables. Make sure the cables are connected to the right connectors at each end and make sure the cables are attached firmly to their respective connectors.
  • Page 24 Panel shows “unsupported format”: That means that the monitor receives a signal source which cannot be displayed. This e.g. may happen when frequencies are set up over 75Hz. When you think the signal should be possible to be displayed please contact the faytech service with detailed signal information.

  • Page 25: Technical Data

    Image is upside down: Press (when there is a signal) the + button. This switches through the two different modes (the original, top / bottom mirrored) TECHNICAL DATA Changes in the sense of technical progress reserved. TIMING-PARAMETER AND SUPPORTED VGA-RESOLUTION Timing-Parameter: 7"...

  • Page 26: Pin Assignment

    Brightness (cd/m2): Contrast: 600:1 Typical reaction time Tr/ Tf (ms): Visual Angle horizontal; vertical (°): 150;130 Working power (V): 8~36 Power consumption (W): Stand-By-Consumption (W): <0,5 Operating temperature (°C): -25~+75 Touch Panel: 4-wire resistive Touch Connectors: 1 x USB port, 1 x serial port Touch Panel-driver: Windows, Linux, Mac Touch life (contacts):...
  • Page 27 VIDEO: 1: AUDIO_IN_L 3: AV1 5: AV2 7: Pr+ 9: Y+ 2: AUDIO_IN_R 4:GND 6: CarControl 8: GND 10: Pb+ SERIAL: 1: +5V 3: RX 2: GND 4: XT VGA, HDMI, USB-B, EAR-In: Standard connectors...
  • Page 28 Wenden Sie sich bei einem mutmaßlichen Defekt bitte immer zunächst an uns. Unsere ausgebildeten Fachkräfte helfen Ihnen gerne weiter. Liegt tatsächlich ein Defekt vor erhalten Sie über support@faytech.de eine RMA-Nr. (Return Merchandise Authorization). Senden Sie das defekte Teil mit deutlicher Anbringung der RMA-Nr. an obige Adresse ein. Zubehörteile wie Kabel, Adapter oder Netzteile tauschen wir in der Regel unkompliziert vorab aus.
  • Page 29 Anything received with postage due will be returned to you without any testing or resolution. Within the first 30 days after you buy a new faytech product, we will refund your shipping costs for returned products. For the rest of the warranty period, we will pay the shipping costs for any repaired or replaced items that we ship back to you.
  • Page 30 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Table of Contents