Wyre Storm MX-0606-HDBT-H2L Quick Start Manual

6x6/8x8 4K HDBaseT Matrix
with HDCP 2.2 support (35m/115ft)
MX-0606-HDBT-H2L | MX-0808-HDBT-H2L v1
WyreStorm recommends reading through this document in its entirety to become familiar with the product's features prior to starting the installation
process.
In the Box
1x MX-0606-HDBT-H2L or MX-0808-HDBT-H2L Matrix Switcher
1x IR Remote Handset
1x IR Receiver (38Khz)
6/8x Wide-band IR Receivers (30-50KHz)
6/8x IR Emitters
1x USB to DB9 RS-232 Cable
1x 100~240V AC 50/60Hz Power Cord with US Plug
1x 100~240V AC 50/60Hz Power Cord with UK Plug
1x 100~240V AC 50/60Hz Power Cord with EU Plug
2x Mounting Brackets
1x Quickstart Guide (this document)
Basic Wiring Diagram
UHD Source
MX-0808-HDBT-H2L
Key
HDMI/Digital Video
HDBaseT/Ethernet
Digital Audio
IR
RS-232
IMPORTANT!
Disconnecting and connecting (hot plugging) HDMI or HDBaseT while devices
are powered on may cause damage. WyreStorm recommends powering off
devices before disconnecting these connections.
Reccomended Products
To take full advantage of the features of this matrix, WyreStorm recommends
the following products be used within the system.
• RX-70-POH HDBaseT Receiver – Use this receiver when 4K HDCP 2.2
output is required to a display.
• CAB-IR-LINK – Use this cable when using an IR control system for matrix
control of HDBaseT pass-through.
Copyright © 2017 WyreStorm Technologies |
MX-0606-HDBT-H2L | MX-0808-HDBT-H2L v1 Quickstart Guide | 170418
Router
CAB-IR-LINK (Sold
Control System
Separately)
RX-70-POH
wyrestorm.com
Additional Information
This Quickstart Guide provides the basic steps for the common uses of this
product. Detailed installation and configuration information may be found in
the download tab located on the product page.
• WebUI Reference Guide – Setup for advanced Matrix features such as IP
and testing of connections
• H2 Matrix Operation User Guide – Single page document showing the
operation via front panel and included IR remote.
• Drivers and API – Preconfigured drivers for popular control systems and
API document.
Installation
Before Beginning
• WyreStorm recommends visiting the product page before installing this
product for updates to this Quickstart Guide as well as other information
about the product.
• Verify that all items are included in the packaging per the
Pre Wire
1. Run a Cat5e/6/6a cable from the matrix location to the receiver location.
See Video Resolutions in the
cable type and length. Terminate the cable per the
Wiring section.
2. (Optional) If using IR emitters or connecting blocks, run the wire and
terminate per the IR TX (Emitter) Wiring
3. (Optional) If using IR receivers at either the transmitter or receiver, run
the wire and terminate per the IR RX/Ext (Receiver) Wiring section.
4. (Optional) If using RS-232 pass-through, run the wire and terminate per
the RS-232 Wiring section.
Installation
1. Connect an HDMI source to the HDMI In on the matrix using a cable
from a high quality brand such as
additional sources.
2. Using the cable created in
female plug to the HDBT Out jack on the matrix. Repeat for additional
HDBaseT receivers.
3. (Optional) Using the included IR emitter or the cable created in
step 2, place an IR emitter onto a source device near the device's IR
sensor. Connect the 3.5mm (1/8in) Mono Plug to an IR TX port. Repeat
for additional sources.
4. Using the included IR receiver, connect the 3.5mm (1/8in) Stereo
Plug to an IR RX (IR to Zone) port. If using a control system, use the
WyreStorm CAB-IR-LINK
for additional zones.
5. (Optional) Using an included IR receiver, connect the 3.5mm (1/8in)
Stereo Plug to an IR Ext port. If using a control system, use the
WyreStorm CAB-IR-LINK
6. (Optional) Using the cable created in
DB9 male jack to the RS-232 port on the matrix and the opposite end to
an RS-232 control system.
7. Install HDBaseT receivers (RX-70-POH recommended) following the
instructions provided with the model being installed.
UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)
1 of 4
Quickstart Guide
In the Box
Specifications table before determining
HDMI/HDBaseT
section.
WyreStorm Express. Repeat for
Pre Wire step 1, connect the 8-pin RJ-45
or the cable created in Pre Wire step 3. Repeat
or the cable created in Pre Wire step 3.
Pre Wire step 4, connect the 9-pin
support@wyrestorm.com
list.
Pre Wire