Advertisement
CUTTING SAFETY
WARNING:
Inspect the area before
each use. Remove objects (rocks, broken
glass, nails, wire, etc.) which can be thrown
by or become entangled in line. Hard objects
can damage trimmer head and be thrown
causing serious injury.
S Use only for trimming, mowing, and sweep-
ing. Do not use for edging, pruning, or
hedge trimming.
S Keep firm footing and balance. Do not over-
reach.
S Keep all parts of your body away from spin-
ning line and muffler. Keep engine below waist
level. A hot muffler can cause serious burns.
S Cutting with the line on right side of the
shield will throw debris away from the oper-
ator.
S Use only in daylight or good artificial light.
TRANSPORTING AND STORAGE
S Allow the engine to cool; secure unit before
storing or transporting in vehicle.
S Empty the fuel tank before storing or trans-
porting the unit. Use up fuel left in the car-
buretor by starting the engine and letting it
run until it stops.
S Store unit and fuel in an area where fuel va-
pors cannot reach sparks or open flames
from water heaters, electric motors or
switches, furnaces, etc.
S Store unit so line limiter blade cannot acci-
dentally cause injury. Unit can be hung by
the tube.
S Store the unit out of the reach of children
If situations occur which are not covered in
this manual, use care and good judgment. If
you need assistance, call 1-800-554-6723.
SAFETY NOTICE:
Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
people prone to circulation disorders or ab-
normal swellings.
Prolonged use in cold
weather has been linked to blood vessel dam-
age in otherwise healthy people. If symptoms
occur such as numbness, pain, loss of
strength, change in skin color or texture, or
loss of feeling in the fingers, hands, or joints,
discontinue the use of this tool and seek med-
ical attention. An anti--vibration system does
not guarantee the avoidance of these prob-
lems. Users who operate power tools on a
continual and regular basis must monitor
closely their physical condition and the condi-
tion of this tool.
SPECIAL NOTICE:
This unit is equipped
with a temperature limiting muffler and spark
arresting screen which meets the require-
ments of California Codes 4442 and 4443. All
U.S. forest land and the states of California,
Idaho, Maine, Minnesota, New Jersey, Ore-
gon, and Washington require by law that
many
internal
combustion
equipped with a spark arresting screen. If you
operate in a locale where such regulations ex-
ist, you are legally responsible for maintaining
the operating condition of these parts. Failure
to do so is a violation of the law. For normal
homeowner use, the muffler and spark arrest-
ing screen will not require any service. After
50 hours of use, we recommend that your
muffler be serviced or replaced by your autho-
rized service dealer.
WARNING:
repeat all steps to ensure your unit is properly
assembled and all fasteners are secure.
ADJUST THE ASSIST HANDLE
WARNING:
dle, be sure it remains between the trigger
and the safety label.
S Loosen wing nut or knob on handle.
S Rotate the handle on the tube to an upright
position; retighten wing nut.
INSTALLATION OF THE CUTTING
HEAD (if not already installed)
S Secure dust cup with wrench to keep shaft
from turning.
S Slide the trimmer head onto the shaft.
NOTE:
It will be necessary to use a deep
socket to tighten the hex nut.
Dust cup
S Place the alignment washer over the hex
nut.
S Install alignment washer and hex nut by
threading nut onto the arbor shaft clock-
wise.
NOTE:
The hex nut must be centered in the
hole of the cutting head before tightening onto
the arbor shaft.
S Tighten nut securely (10--12 ft--lbs).
ATTACH THE SHIELD
WARNING:
erly installed.
protection from the risk of thrown objects to
the operator and others and is equipped with
a line limiter blade which cuts excess line to
the proper length. The line limiter blade (on
underside of shield) is sharp and can cut you.
S Remove wing nut from shield.
S Insert bracket into slot as shown.
engines
be
S Pivot shield until bolt passes through hole in
bracket.
S Securely tighten wing nut onto bolt.
3
ASSEMBLY
If received assembled,
When ajdusting the han-
Arbor shaft
Hex nut
Alignment
washer
Trimmer head
The shield must be prop-
The shield provides partial
Advertisement
