Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ActionTec WEB5500
Summary of Contents for ActionTec WEB5500
-
Page 1: User Guide
Wireless Network Extender Model # WEB5500 User Guide xxxx-xxxx-000 rev. 1... -
Page 2: Table Of Contents
Table of Contents Introduction Features Getting to Know the Extender Front Panel Back Panel Accessing the Extender’s GUI Status Wireless Setup Advanced Setup Specifications Notices Warranty Important Safety Instructions FCC Class B Equipment Important Note on WiFi Contact Information Technical Support... -
Page 3: Introduction
Introduction The Actiontec WEB5500 is a wireless network extender with dual concurrent radios supporting both 2.4GHz and 5GHz operation in 802.11 a/b/g/n, and also 5GHz in 802.11ac. This allows the Extender to connect to everything from legacy wireless laptops, computers, and gaming platforms, up to the most current (and future) Apple and Android tablets, laptops, media platforms, and smartphones. -
Page 4: Features
WEB5500 Wireless Network Extender Features • Upgrade to 802.11ac speeds without replacing your router • Dual-band concurrent radios for wireless throughput up to 2 Gbps: * 4x4 802.11ac 5 GHz solution * 2x2 2.4 GHz radio • Two gigabit Ethernet ports •... -
Page 5: Getting To Know The Extender
Getting to Know the Extender This chapter describes the location and uses of the Extender’s LEDs, ports, and buttons. Front Panel The front panel features LEDs that illuminate in green when the operation of power, available ports and wireless bands are functioning and in use. -
Page 6: Back Panel
Back Panel • Power port: used to connect the power adapter (external, 12V/1.5A; Actiontec Model: NBS24J120150VU) to the Extender. • Reset button: restores the Extender back to the original factory default settings when held down for at least 10 seconds. -
Page 7: Accessing The Extender's Gui
3. The gateway/modem’s GUI appears. The IP address of the Extender should be displayed on the Main or Home screen of an Actiontec gateway/modem, as indicated below. 4. Write down the IP address of the Extender. - Page 8 Getting to Know the Extender 6. The Extender’s Login screen appears. Enter the Extender’s Username and Password (found on the label located on the back panel of the Extender; see second figure, below). ...
- Page 9 WEB5500 Wireless Network Extender The Extender’s GUI’s Status screen appears, as shown below. ...
-
Page 10: Status
Getting to Know the Extender Status The first GUI screen that appears is the Status screen, which can also be generated by clicking the Status icon in the menu bar. This screen contains basic information about the Extender’s wireless status, network stations, and product information about the Extender. -
Page 11: Wireless Setup
WEB5500 Wireless Network Extender Wireless Setup Clicking the Wireless Setup icon from the menu bar of any of the Extender’s GUI screens generates the Wireless Network List screen. Additional wireless settings can be accessed from the menu on the left side. - Page 12 Getting to Know the Extender Basic Setup The Basic Setup wireless network screen contains various settings regarding the Extender’s wireless network. When finished adjusting the settings in this screen, click Apply. Multiple SSID This option allows the user to setup different SSIDs (wireless networks) with different parameters.
- Page 13 WEB5500 Wireless Network Extender SSID Broadcast This option controls whether or not the name of the network is broadcast to other wireless devices (usually, in the device’s available wireless network list). Select Enable or Disable by clicking in the appropriate radio button.
-
Page 14: Wireless Security
Getting to Know the Extender Password Phrase This option allows the user to enter a custom password phrase or value. Wireless Security The Wireless Security screen allows the user to apply wireless security to the Extender’s wireless network. This screen should be accessed by experienced network technicians only. - Page 15 WEB5500 Wireless Network Extender The WPS screen allows the Extender to accept wireless clients via Wi-Fi Protected Setup (WPS), an automatic wireless network connection protocol. Only experienced network technicians should configure the settings in this screen. Advanced Wireless Setup The Advanced Wireless Setup screen allows the Extender to be configured...
-
Page 16: Wireless Access Control
Getting to Know the Extender Wireless Access Control The Wireless Access Control screen contains a number of advanced settings regarding the Extender’s wireless network. Only experienced network technicians should configure these settings. -
Page 17: Advanced Setup
WEB5500 Wireless Network Extender Advanced Setup Clicking the Advanced Setup icon from any of the Extender’s GUI screens generates the Management screen, along with other advanced settings accessed through the menu on the left side. These settings configure various administrative aspects of the Extender and its GUI. They should be adjusted by an experienced network technicians only. -
Page 18: Factory Default
Getting to Know the Extender Factory Default The Factory Default advanced setup screen allows the Extender’s factory default settings to be reapplied, erasing all current settings. Click Restore Default Settings to restore the Extender to its factory default state. Firmware Restore The Firmware Restore screen lists the active and backup firmware versions available on the Extender. -
Page 19: Firmware Upgrade
WEB5500 Wireless Network Extender Firmware Upgrade Actiontec periodically posts firmware upgrades that may include enhancements and/or bug fixes for the Extender. To upgrade the Extender’s firmware: 1. Go to www.actiontec.com/support for information about the latest firmware available for the Extender. If the version is the same as the current version applied to the Extender, there is no need to upgrade the firmware. -
Page 20: Specifications
Specifications Model Number WEB5500 Certifications Wi-Fi (a, b, g, n, ac) WPA, WPA2 Wi-Fi Protected Setup Wi-Fi 802.11 a/b/g/n/ac IEEE standard 5GHz/2.4GHz LAN Connections Ethernet ports (2): 10/100/1000 LED Indicators Power, WiFi 2.4 GHz, WiFi 5 GHz, LAN Ethernet 1, LAN Ethernet 2... - Page 21 WEB5500 Wireless Network Extender Power External, 12V/1.5A; Actiontec Model: NBS24J120150VU Regulatory FCC part 15, UL-60950-1 Environmental Operating temperature - 0ºC to 40ºC (32ºF to 104ºF) Storage temperature - 0ºC to 70ºC (32ºF to 158ºF) Operating humidity - 10% to 85% non-condensing Storage humidity - 5% to 95% non-condensing Altitude: -197 ft.
-
Page 22: Notices
To the extent that this Limited Warranty Statement is inconsistent with local law, this Statement shall be deemed modified to be consistent with such local law. Under such local law, certain disclaimers and limitations of this Warranty Statement may not apply to the customer. Go to http://www.actiontec.com/products/warranty.php for more information. -
Page 23: Important Safety Instructions
WEB5500 Wireless Network Extender Important Safety Instructions Basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and personal injury, including the following: • Do not use this product near water – for example, near a bathtub, kitchen sink, laundry tub, or swimming pool, or in a wet basement;... -
Page 24: Fcc Class B Equipment
Consult the dealer or an experience radio or television technician for help. Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Actiontec Electronics, Inc, may void the user’s authority to operate the equipment. -
Page 25: Important Note On Wifi
WEB5500 Wireless Network Extender Declaration of Conformity for Products Marked With the FCC logo This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference;... -
Page 26: Contact Information
The transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Contact Information For questions regarding your product or the FCC declaration, contact: Actiontec Electronics, Inc 760 North Mary Avenue Sunnyvale, CA 94085 United States ...
Need help?
Do you have a question about the WEB5500 and is the answer not in the manual?
Questions and answers