Page 1 2 0 1 7 F I AT 5 00 X U S ER GU I D E ®...
Page 2 If you are the first registered retail owner of your vehicle, you may obtain a complimentary printed copy of the Owner’s Manual, Navigation/Uconnect Manuals or Warranty Booklets by calling 1 888 242-6342 (U.S.) or 1 800 387-1143 (Canada) or by contacting your dealer. The driver’s primary responsibility is the safe operation of the vehicle.
Page 3: Table Of Contents
CARGO AREA FEATURES ... .144 WELCOME FROM FIAT ....2 TRAILER TOWING ....145...
Page 4: Introduction/Welcome
INTRODUCTION/WELCOME WELCOME FROM FIAT Congratulations on selecting your new FIAT vehicle. Be assured that it represents preci- sion workmanship, distinctive styling, and high quality. Your new FIAT vehicle has characteristics to enhance the driver's control under some driving conditions. These are to assist the driver and are never a substitute for attentive driving.
Page 5 INTRODUCTION/WELCOME VEHICLES SOLD IN CANADA With respect to any vehicles sold in Canada, the name FCA US LLC shall be deemed to be deleted and the name FCA Canada Inc. used in substitution (excluding legal lines). WARNING! • Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious personal injury.
Page 6: Controls At A Glance
CONTROLS AT A GLANCE DRIVER COCKPIT 1. Headlight Switch pg. 59 2. Instrument Cluster Display Controls pg. 140 3. Turn Signal/Light Lever pg. 61 4. Speedometer pg. 6 5. Instrument Cluster Display pg. 141 6. Electronic Speed Control pg. 66 7.
Page 7 CONTROLS AT A GLANCE 11. Glove Compartment 12. Climate Controls pg. 69 13. Media Hub – Playing iPod/USB/MP3/Aux Devices pg. 100 14. Power Outlet pg. 143 15. Gear Selector 16. Heated Seats — If Equipped pg. 53 17. Power Mirror Switch 18.
Page 8: Instrument Cluster
CONTROLS AT A GLANCE INSTRUMENT CLUSTER 1. Speedometer 2. Fuel Gauge 3. Instrument Cluster Display (See page 148 for Instrument Cluster Warning Lights information.)
Page 9 CONTROLS AT A GLANCE 4. Temperature Gauge 5. Tachometer (See page 154 for Instrument Cluster Indicator Lights information.)
Page 10: Getting Started
GETTING STARTED KEY FOB The Keyless Enter-N-Go feature allows the driver to operate the ignition switch with the push of a button as long as the key fob is in the passenger compartment. The Keyless Push Button Ignition has three operating modes.
Page 11: Remote Start
GETTING STARTED • When leaving the vehicle, always remove the key fob from the ignition and lock your vehicle. If equipped with Keyless Enter-N-Go, always make sure the ignition is in OFF mode, remove the key fob from the vehicle and lock the vehicle. •...
Page 12: Vehicle Security Alarm
GETTING STARTED VEHICLE SECURITY ALARM The vehicle security alarm monitors the vehicle doors for unauthorized entry and the Keyless Enter-N-Go START/STOP button for unauthorized operation. While the vehicle security alarm is armed, interior switches for door locks and liftgate release are disabled. If something triggers the alarm, the vehicle security alarm will provide the following au- dible and visible signals: the horn will pulse, the park lamps and/or turn signals will flash, and the vehicle security light in the instrument cluster will flash.
Page 13: Keyless Enter-N-Go - Passive Entry
GETTING STARTED KEYLESS ENTER-N-GO — PASSIVE ENTRY The Keyless Enter-N-Go system is an enhancement to the vehicle’ s Remote Keyless Entry (RKE) feature. This feature allows you to lock and unlock the vehicle's door(s) and liftgate without having to push the key fob lock or unlock buttons, as well as starting and stop- ping the vehicle with the push of a button.
Page 14 GETTING STARTED Do NOT grab the door handle when pushing the door handle lock button. This could unlock the door(s). Push The Door Handle Button To Lock Do NOT Grab The Handle And Button When Locking NOTE: • If “Unlock All Doors 1st Press” is programmed, all doors will unlock when you grab hold of the front driver's door handle.
Page 15 GETTING STARTED Lock Or Unlock The Liftgate To Lock The Liftgate With a valid Passive Entry key fob within 5 ft (1.5 m) of the liftgate, push the Passive Entry lock button located to the right of the Passive Entry liftgate unlock/release but- ton.
Page 16: Keyless Enter-N-Go - Ignition
GETTING STARTED KEYLESS ENTER-N-GO — IGNITION Engine Starting/Stopping Starting 1. With a valid key fob inside the vehicle. 2. Place the gear selector in PARK or NEUTRAL. 3. While pushing the brake pedal, push the ENGINE START/STOP button once. If the engine fails to start, the starter will disengage automatically after 10 sec- onds.
Page 17: Occupant Restraint Systems
GETTING STARTED RUN Position With Engine Off NOTE: The following functions are with the driver’ s foot OFF the Brake Pedal (Transmission in PARK or NEUTRAL Position). Starting With The Ignition In The OFF Mode: 1. Push the ENGINE START/STOP button once to change the ignition to the RUN mode.
Page 18 GETTING STARTED 3. Children that are not big enough to wear the vehicle seat belt properly (refer to “Child Restraints” in this section for further information) should be secured in a ve- hicle with a rear seat in child restraints or belt-positioning booster seats. Older chil- dren who do not use child restraints or belt-positioning booster seats should ride properly buckled up in a vehicle with a rear seat.
Page 19 GETTING STARTED Enhanced Seat Belt Use Reminder System (BeltAlert) Driver And Passenger BeltAlert — If Equipped BeltAlert is a feature intended to remind the driver and outboard front seat passenger (if equipped with outboard front passenger seat BeltAlert) to buckle their seat belts. The Belt Alert feature is active whenever the ignition switch is in the START or ON/RUN posi- tion.
Page 20 GETTING STARTED BeltAlert can be activated or deactivated by your authorized dealer. FCA US LLC does not recommend deactivating BeltAlert. NOTE: If BeltAlert has been deactivated and the driver or outboard front seat passenger (if equipped with outboard front passenger seat BeltAlert) is unbuckled the Seat Belt Re- minder Light will turn on and remain on until the driver and outboard front seat passen- ger seat belts are buckled.
Page 21 GETTING STARTED WARNING! • A lap belt worn too high can increase the risk of injury in a collision. The seat belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Al- ways wear the lap part of your seat belt as low as possible and keep it snug. •...
Page 22 GETTING STARTED Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, and next to your arm in the rear seat (for vehicles equipped with a rear seat).
Page 23 GETTING STARTED Adjustable Upper Shoulder Belt Anchorage In the driver and front passenger seats, the top of the shoulder belt can be adjusted up- ward or downward to position the seat belt away from your neck. Push or squeeze the anchorage button to release the anchorage, and move it up or down to the position that serves you best.
Page 24 GETTING STARTED Seat Belts And Pregnant Women Seat belts must be worn by all occupants including pregnant women: the risk of injury in the event of an accident is reduced for the mother and the unborn child if they are wearing a seat belt. Position the lap belt snug and low below the abdomen and across the strong bones of the hips.
Page 25 GETTING STARTED Switchable Automatic Locking Retractors (ALR) The seat belts in the passenger seating positions are equipped with a Switchable Auto- matic Locking Retractor (ALR) which is used to secure a child restraint system. For addi- tional information, refer to “Installing Child Restraints Using The Vehicle Seat Belt” under the “Child Restraints”...
Page 26 GETTING STARTED How To Disengage The Automatic Locking Mode Unbuckle the combination lap/shoulder belt and allow it to retract completely to disen- gage the Automatic Locking Mode and activate the vehicle sensitive (emergency) locking mode. WARNING! • The seat belt assembly must be replaced if the switchable Automatic Locking Re- tractor (ALR) feature or any other seat belt function is not working properly when checked according to the procedures in the Service Manual.
Page 27 GETTING STARTED Air Bag Warning Light The ORC monitors the readiness of the electronic parts of the air bag system whenever the ignition switch is in the START or ACC/ON/RUN position. If the ignition switch is in the STOP/OFF/LOCK position or in the ACC position, the air bag system is not on and the air bags will not inflate.
Page 28 GETTING STARTED has come on and a fault has been detected. If the Redundant Air Bag Warning Light comes on intermittently or remains on while driving have an authorized dealer service the vehicle immediately. For additional information regarding the Redundant Air Bag Warning Light, refer to “Warning And Indicator Lights”...
Page 29 GETTING STARTED Driver And Passenger Front Air Bag Features The Advanced Front Air Bag system has multistage driver and front passenger air bags. This system provides output appropriate to the severity and type of collision as deter- mined by the Occupant Restraint Controller (ORC), which may receive information from the front impact sensors (if equipped) or other system components.
Page 30 GETTING STARTED Front Air Bag Operation Front Air Bags are designed to provide additional protection by supplementing the seat belts. Front air bags are not expected to reduce the risk of injury in rear, side, or rollover collisions. The front air bags will not deploy in all frontal collisions, including some that may produce substantial vehicle damage —...
Page 31 GETTING STARTED Supplemental Side Air Bags Your vehicle is equipped with two types of side air bags: 1. Supplemental Seat-Mounted Side Air Bags (SABs): Located in the outboard side of the front seats. The SABs are marked with a “SRS AIRBAG” or “AIRBAG” label sewn into the outboard side of the seats.
Page 32 GETTING STARTED 2. Supplemental Side Air Bag Inflatable Curtains (SABICs): Located above the side win- dows. The trim covering the SABICs is labeled “SRS AIRBAG” or “AIRBAG.” SABICs may help reduce the risk of head or other injuries to front and rear seat outboard occupants in cer- tain side impacts and/or vehicle roll- over events, in addition to the injury...
Page 33 GETTING STARTED Side Air Bags are a supplement to the seat belt restraint system. Side Air Bags deploy in less time than it takes to blink your eyes. WARNING! • Occupants, including children, who are up against or very close to Side Air Bags can be seriously injured or killed.
Page 34 GETTING STARTED Rollover Events Side Air Bags are designed to activate in certain rollover events. The ORC determines whether the deployment of the Side Air Bags in a particular rollover event is appropriate, based on the severity and type of collision.Vehicle damage by itself is not a good indica- tor of whether or not Side Air Bags should have deployed.
Page 35 GETTING STARTED If A Deployment Occurs The front air bags are designed to deflate immediately after deployment. NOTE: Front and/or side air bags will not deploy in all collisions. This does not mean something is wrong with the air bag system. If you do have a collision which deploys the air bags, any or all of the following may oc- cur: •...
Page 36 GETTING STARTED Enhanced Accident Response System In the event of an impact, if the communication network remains intact, and the power remains intact, depending on the nature of the event, the ORC will determine whether to have the Enhanced Accident Response System perform the following functions: •...
Page 37 GETTING STARTED Customer Action Customer Will See NOTE: Each step MUST BE held for at least 2 seconds Right turn light is OFF. 8. Place turn signal in neutral state. Left turn light BLINKS Right turn light is ON SOLID. 9.
Page 38: Child Restraints
GETTING STARTED Event Data Recorder (EDR) This vehicle is equipped with an event data recorder (EDR). The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an air bag deploy- ment or hitting a road obstacle, data that will assist in understanding how a vehicle’ s sys- tems performed.
Page 39 GETTING STARTED There are different sizes and types of restraints for children from newborn size to the child almost large enough for an adult safety belt. Always check the child seat Owner’ s Manual to make sure you have the correct seat for your child. Carefully read and follow all the instructions and warnings in the child restraint Owner’...
Page 40 GETTING STARTED Infant And Child Restraints Safety experts recommend that children ride rear-facing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear-facing child restraint. Two types of child restraints can be used rear-facing: infant carriers and convert- ible child seats.
Page 41 GETTING STARTED WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the child restraint manufacturer’ s directions exactly when installing an infant or child restraint.
Page 42 GETTING STARTED WARNING! Never allow a child to put the shoulder belt under an arm or behind their back. In a crash, the shoulder belt will not protect a child properly, which may result in serious injury or death. A child must always wear both the lap and shoulder portions of the seat belt correctly.
Page 43 GETTING STARTED Lower Anchors And Tethers For CHildren (LATCH) Restraint System Your vehicle is equipped with the child re- straint anchorage system called LATCH, which stands for Lower Anchors and Teth- ers for CHildren. The LATCH system has three vehicle anchor points for installing LATCH-equipped child seats.
Page 44 GETTING STARTED Frequently Asked Questions About Installing Child Restraints With LATCH Use the LATCH anchorage sys- tem until the combined weight of What is the weight limit (child’ s the child and the child restraint is weight + weight of the child re- 65 lbs (29.5 kg).
Page 45 GETTING STARTED Locating The LATCH Anchorages The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback, below the anchorage symbols on the seatback. They are just visible when you lean into the rear seat to install the child restraint.You will easily feel them if you run your finger along the gap between the seatback and seat cushion.
Page 46 GETTING STARTED Center Seat LATCH WARNING! • Do not install a child restraint in the center position using the LATCH system. This position is not approved for installing child seats using the LATCH attachments.You must use the seat belt and tether anchor to install a child seat in the center seat- ing position.
Page 47 GETTING STARTED How To Stow An Unused Switchable-ALR (ALR) Seat Belt When using the LATCH attaching system to install a child restraint, stow all ALR seat belts that are not being used by other occupants or being used to secure child restraints. An unused belt could injure a child if they play with it and accidentally lock the seat belt retractor.
Page 48 GETTING STARTED Refer to the “Automatic Locking Mode” description in “Switchable Automatic Locking Re- tractors (ALR)” under “Occupant Restraint Systems” for additional information on ALR. Please see the table below and the following sections for more information. Lap/Shoulder Belt Systems For Installing Child Restraints In This Vehicle Automatic Locking Retractor (ALR) Locations ALR = Switchable Automatic Locking...
Page 49 GETTING STARTED Installing A Child Restraint With A Switchable Automatic Locking Retractor (ALR): Child restraint systems are designed to be secured in vehicle seats by lap belts or the lap belt portion of a lap/shoulder belt. WARNING! • Improper installation or failure to properly secure a child restraint can lead to fail- ure of the restraint.
Page 50 GETTING STARTED Installing Child Restraints Using The Top Tether Anchorage: WARNING! Do not attach a tether strap for a rear-facing car seat to any location in front of the car seat, including the seat frame or a tether anchorage. Only attach the tether strap of a rear-facing car seat to the tether anchorage that is approved for that seating position, located behind the top of the vehicle seat.
Page 51: Head Restraints
GETTING STARTED WARNING! • An incorrectly anchored tether strap could lead to increased head motion and pos- sible injury to the child. Use only the anchorage position directly behind the child seat to secure a child restraint top tether strap. •...
Page 52 GETTING STARTED NOTE: Do not reposition the head restraint 180 degrees to the incorrect position in an attempt to gain additional clearance to the back of the head. WARNING! • A loose head restraint thrown forward in a collision or hard stop could cause seri- ous injury or death to occupants of the vehicle.
Page 53: Seats
GETTING STARTED SEATS Seats are a part of the Occupant Restraint System of the vehicle. WARNING! • It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. •...
Page 54 GETTING STARTED Height Adjustment The front driver and passenger seats height can be raised or lowered by using a lever, located on the outboard side of the seat. Pull upward on the lever to raise the seat height or push downward on the lever to lower the seat height. Recline Adjustment To adjust the seatback, lift the lever located on the outboard side of the seat, lean back to the desired position and release the lever.
Page 55 GETTING STARTED Heated Seats — If Equipped The heated seat switches are located on the instrument panel. You can choose between two heating levels: • Push the heated seat button once to turn the HI setting on. • Push the heated seat button a second time to turn the LO setting on.
Page 56 GETTING STARTED Rear Seats The split rear seat increases the storage of the rear cargo area. NOTE: • Prior to folding the rear seat down, it may be necessary to position the front seat to its mid-track position. Be sure that the front seats are fully upright and positioned for- ward, this will allow the rear seat to fold down easily.
Page 57 GETTING STARTED Cargo Area Enlargement Folding both sides of the rear seat provides additional storage in the rear cargo area. Proceed as follows: 1. Remove the rear shelf (if equipped). 2. Fully lower the rear seat head restraints. 3. Move the safety belts to the outboard side of the seat.
Page 58: Steering Wheel
GETTING STARTED STEERING WHEEL Tilt/Telescoping Steering Column This feature allows you to tilt the steering column upward or downward. It also allows you to lengthen or shorten the steering column. The tilt/telescoping lever is located be- low the steering wheel at the end of the steering column. To unlock the steering column, push the tilt/telescoping lever downward (toward the floor).
Page 59 GETTING STARTED Heated Steering Wheel — If Equipped The steering wheel contains a heating element that helps warm your hands in cold weather. The heated steering wheel has only one temperature setting. Once the heated steering wheel switch has been turned on, it will operate for an average of 80 min- utes or more before automatically shutting off.
Page 60: Operating Your Vehicle
OPERATING YOUR VEHICLE ENGINE BREAK-IN RECOMMENDATIONS A long break-in period is not required for the engine and drivetrain (transmission and axle) in your vehicle. Drive moderately during the first 300 miles (500 km). After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable.
Page 61: Exterior Lights
OPERATING YOUR VEHICLE EXTERIOR LIGHTS Headlights The headlight switch is located on the left side of the instrument panel. The headlight switch controls the operation of the headlights, side marker lights, daytime running lights, fog lights and the dimming of the instrument cluster and interior lighting. Turning on the headlights will illuminate the instrument cluster and the controls located on the instrument panel.
Page 62 OPERATING YOUR VEHICLE Front Fog Lights — If Equipped The front fog light switch is built into the headlight switch. To activate the front fog lights, turn on the parking lights or the low beam headlights and push the headlight switch. To turn off the front fog lights, push the headlight switch a sec- ond time or turn off the headlight switch.
Page 63 OPERATING YOUR VEHICLE High Beams To turn on the high beam headlights, push the turn signal lever forward (toward the front of the vehicle) and an indicator will illuminate in the cluster. To turn off the high beams, pull the turn signal lever rearward (toward the rear of the vehicle). NOTE: The headlights must be on for the high beams to activate.
Page 64: Wipers And Washers
OPERATING YOUR VEHICLE WIPERS AND WASHERS Front Wiper Operation The windshield wiper/washer controls are located on the lever on the right side of the steering column. The front wipers are operated by rotating a switch, located on the end of the lever. Windshield Wiper Stalk 1 —...
Page 65 OPERATING YOUR VEHICLE Windshield Washer Operation To use the washer, pull the lever toward you and hold while spray is desired. If the lever is pulled while in the intermittent setting, the wipers will turn on and operate for several wipe cycles after the lever is released, and then resume the intermittent interval previ- ously selected.
Page 66 OPERATING YOUR VEHICLE • The Rain Sensing feature can be turned on and off using the Uconnect System, refer to “Uconnect Settings” in “Multimedia” in the Owner’ s Manual on www.fiatusa.com/en/owners/manuals for further information. The Rain Sensing system has protection features for the wiper blades and arms, and will not operate under the following conditions: •...
Page 67 OPERATING YOUR VEHICLE Rear Window Defroster The rear window defroster button is located with the Climate Controls on the instru- ment panel. Push this button to turn on the rear window defroster. An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after approximately 20 minutes.
Page 68: Speed Control
OPERATING YOUR VEHICLE SPEED CONTROL When engaged, the Speed Control takes over accelerator operations at speeds greater than 25 mph (40 km/h). The Speed Control buttons are located on the right side of the steering wheel. NOTE: In order to ensure proper operation, the Speed Control System has been designed to shut down if multiple Speed Control functions are operated at the same time.
Page 69 OPERATING YOUR VEHICLE Pushing the on/off button or turning the ignition switch to STOP erases the set speed from memory. Resume Speed To resume a previously set speed, push the RES button and release. Resume can be used at any speed above 20 mph (32 km/h). Varying The Speed To Increase Speed When the Speed Control is set, you can increase speed by pushing the SET (+) button.
Page 70: Manual Climate Controls
OPERATING YOUR VEHICLE Accelerating For Passing Press the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. MANUAL CLIMATE CONTROLS Manual Climate Controls 1 — Blower Control 4 — Rear Defroster 2 —...
Page 71: Automatic Temperature Controls (Atc)
OPERATING YOUR VEHICLE AUTOMATIC TEMPERATURE CONTROLS (ATC) Automatic Temperature Controls (ATC) 1 — Driver Temperature Control 8 — Passenger Temperature Display 2 — A/C Control 9 — SYNC Control 3 — MAX Front Defrost Control 10 — Rear Defroster 4 — Blower Control 11 —...
Page 72: Electric Park Brake (Epb)
OPERATING YOUR VEHICLE Max Defrost • Push the MAX Defrost button to change the current airflow setting to Defrost mode. Performing this function will cause the blower speed to increase to high blower, the A/C compressor to turn on, the driver and passenger temperatures set to HI, rear defroster to turn on, and recirculation to turn off.
Page 73 OPERATING YOUR VEHICLE The park brake can also be automatically released if the driver’ s seat belt is buckled and driver's intention to start (in forward or reverse direction) is recognized by the system. NOTE: On a manual transmission vehicle, if the clutch pedal is released at the same time the gas pedal is pressed, the EPB will be automatically released.
Page 74 OPERATING YOUR VEHICLE WARNING! • When leaving the vehicle, always remove the key fob from the ignition and lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Al- lowing children to be in a vehicle unattended is dangerous for a number of rea- sons.
Page 75: Dynamic Selector - If Equipped
OPERATING YOUR VEHICLE DYNAMIC SELECTOR — IF EQUIPPED The Dynamic Selector combines the capabilities of the vehicle control systems, along with driver input, to provide the best performance in all driving conditions. The Dynamic Selector consists of the fol- lowing positions: Auto Mode –...
Page 76: Blind Spot Monitoring (Bsm) - If Equipped
OPERATING YOUR VEHICLE BLIND SPOT MONITORING (BSM) — IF EQUIPPED The Blind Spot Monitoring (BSM) system uses two radar-based sensors, located inside the rear bumper fascia, to detect highway licensable vehicles (automobiles, trucks, motorcycles, etc.) that enter the blind spot zones from the rear/front/side of the vehicle. When the vehicle is started, the BSM warning light will momentarily illuminate in both outside rear view mirrors to let the driver know that the system is operational.
Page 77 OPERATING YOUR VEHICLE Overtaking Traffic If you pass another vehicle slowly with a relative speed less than 15 mph (25 km/h) and the vehicle remains in the blind spot for approximately 1.5 seconds, the warning light will be illuminated. If the difference in speed between the two vehicles is greater than 15 mph (25 km/h), the warning light will not illuminate.
Page 78 OPERATING YOUR VEHICLE WARNING! RCP is not a back up aid system. It is intended to be used to help a driver detect an oncoming vehicle in a parking lot situation. Drivers must be careful when backing up, even when using RCP. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up.
Page 79: Brake Control - If Equipped
OPERATING YOUR VEHICLE Blind Spot Monitoring Fault Warnings Sensor Blinded In the case of a sensor blinded: • BSM Mirror Warning Lights are turned on continuously. • A instrument cluster message will display “Blind Spot Monitoring Unavailable - Wipe Rear Bumper Corners.” NOTE: The rear bumper must be clean and free of any obstructing debris.
Page 80 OPERATING YOUR VEHICLE Vehicles With A Manual Transmission: After the end of the intervention of automatic braking, the engine could stall, unless the driver can depress the clutch pedal. Vehicles With Automatic Transmission: After the end of the intervention of automatic braking, the transmission may remain in last gear stored: therefore the car could lurch forward, once the brakes release a few seconds later.
Page 81 OPERATING YOUR VEHICLE Turning Brake Control On Or Off The Brake Control menu setting is located in the Uconnect settings. NOTE: The default status of Brake Control is “Warning + Active Braking.” This allows the system to warn you of a possible collision with the vehicle in front of you and enable the active braking.
Page 82 OPERATING YOUR VEHICLE Brake Control Limited Warning If the instrument cluster display will read “Brake Control Limited Functionality” or “Brake Control Limited Functionality Clean Front Windshield” momentarily, there may be a con- dition that limits Brake Control functionality. Although the vehicle is still drivable under normal conditions, the active braking may not be fully available.
Page 83: Lanesense - If Equipped
OPERATING YOUR VEHICLE Precautions While Driving With Brake Control In certain driving conditions, such as: • Driving in the vicinity of a curve • Small vehicles and/or not aligned to the lane • Lane changing of other vehicles • Passing of vehicles in an oncoming intersection The intervention of the system could be unexpected or delayed.
Page 84 OPERATING YOUR VEHICLE When only a single lane marking is detected and the driver unintentionally drifts across the lane marking (no turn signal applied), the LaneSense system provides a visual warning through the instrument cluster display to prompt the driver to remain within the lane. When only a single lane marking is detected, a haptic (torque) warning will not be provided.
Page 85 OPERATING YOUR VEHICLE Left Lane Departure — Both Lanes Detected • When the LaneSense system is on, the lane lines turn from gray to white to indicate that both of the lane markings have been detected. The LaneSense indicator is solid green when both lane markings have been detected and the system is “armed”...
Page 86: Parksense Rear Park Assist - If Equipped
OPERATING YOUR VEHICLE PARKSENSE REAR PARK ASSIST — IF EQUIPPED The ParkSense Rear Park Assist system provides visual and audible indications of the dis- tance between the rear fascia and a detected obstacle when backing up, e.g. during a parking maneuver. ParkSense will retain the last system state (enabled or disabled) from the last ignition cycle when the ignition is changed to RUN mode.
Page 87 OPERATING YOUR VEHICLE Instrument Cluster Display ParkSense is displayed on the instrument cluster only if you have selected the item "Sound And Display" inside the "Settings" menu of the Uconnect system. If an obstacle is detected in the center rear region, the display will show a single solid arc in the center rear region and will produce a one-half second tone.
Page 88 OPERATING YOUR VEHICLE Service The Rear Park Assist System During vehicle start up, when the ParkSense Rear Park Assist System has detected a faulted condition, the instrument cluster will actuate a single chime, once per ignition cycle, and it will display a dedicated message such as “PARK ASSIST UNAVAILABLE WIPE REAR SENSORS”...
Page 89 OPERATING YOUR VEHICLE WARNING! • Drivers must be careful when backing up even when using ParkSense. Always check carefully behind your vehicle, look behind you, and be sure to check for pe- destrians, animals, other vehicles, obstructions, and blind spots before backing up. You are responsible for safety and must continue to pay attention to your sur- roundings.
Page 90: Parkview Rear Back Up Camera - If Equipped
OPERATING YOUR VEHICLE PARKVIEW REAR BACK UP CAMERA — IF EQUIPPED The ParkView Rear Back Up Camera that allows you to see an on-screen image of your vehicle's rear surroundings when the gear selector is put into REVERSE. The image will be displayed on the touchscreen display along with a note to “check entire surroundings”...
Page 91 OPERATING YOUR VEHICLE The following table shows the approximate distances for each zone: Zone Distance To The Rear Of The Vehicle 0 - 1 ft (0 - 30 cm) Yellow 1 ft - 3 ft (30 cm - 1 m) Green 3 ft or greater (1 m or greater) NOTE:...
Page 92: Electronics
ELECTRONICS YOUR VEHICLE'S SOUND SYSTEM 1. Uconnect Phone Button pg. 129 2. Uconnect Voice Command Button pg. 135 3. Phone Hang Up Button 4. Left Steering Wheel Audio Controls (Located Behind The Steering Wheel) pg. 140 5. Right Steering Wheel Audio Controls (Located Behind The Steering Wheel) pg. 140 6.
Page 93 ELECTRONICS 7. Uconnect 5.0 pg. 97 8. Settings Button pg. 142 9. Tune/Scroll Knob – Browse/Enter Button 10. AUX Jack pg. 100 11. USB Port pg. 100 12. Front Power Outlet pg. 143...
Page 94: Cybersecurity
ELECTRONICS CYBERSECURITY Your vehicle may be a connected vehicle and may be equipped with both wired and wireless networks. These networks allow your vehicle to send and receive information. This information allows systems and features in your vehicle to function properly. Your vehicle may be equipped with certain security features to reduce the risk of unau- thorized and unlawful access to vehicle systems and wireless communications.Vehicle soft- ware technology continues to evolve over time and FCA US LLC, working with its suppli-...
Page 95: Identifying Your Radio
ELECTRONICS IDENTIFYING YOUR RADIO Radio 3.0 • 3.0” Display • Three buttons on the faceplate on either side of the display Radio 3.0 Uconnect 5.0 • 5.0” Full Color Touchscreen Display • Bluetooth Connectivity/Bluetooth Streaming Audio Uconnect 5.0 Uconnect 6.5 NAV •...
Page 96: Radio 3.0
ELECTRONICS RADIO 3.0 Radio 3.0 Buttons 1 — RADIO Button 7 — BACK Button 2 — INFO Button 8 — SEEK Next Button 3 — AUDIO Button 9 — SEEK Previous Button 4 — MENU Button 10 — Play/Pause — Mute Button 5 —...
Page 97 ELECTRONICS Audio Push the AUDIO button on the radio faceplate. The Audio Menu shows the following options for you to customize your audio settings. Treble, Mid, Bass, Fade, Balance, Speed Adjusted Volume, Loudness Select the desired setting to adjust, then push the ENTER/BROWSE button. Turn the TUNE/SCROLL knob to adjust the setting + or - 9.
Page 98 ELECTRONICS Audio Jack (AUX) • The AUX allows a portable device such as an MP3 player or an iPod to be plugged into the radio and utilize the vehicle’ s audio system, using a 3.5 mm audio cable, to amplify the source and play through the vehicle’ s speakers. •...
Page 99: Uconnect 5.0
ELECTRONICS UCONNECT 5.0 Uconnect 5.0 Radio Buttons 1 — On/Off Button 7 — APPS Button 2 — Mute Button 8 — PHONE Button 3 — Screen Off Button 9 — TRIP Button 4 — Settings Button 10 — MEDIA Button 5 —...
Page 100 ELECTRONICS 3. Press the “Up” or “Down” arrows to adjust the hours or minutes, then select the “AM” or “PM” button on the touchscreen. You can also select 12hr or 24hr format by pressing the desired button on the touchscreen. 4.
Page 101 ELECTRONICS Radio Operation Radio Operation 1 — Radio Station Preset 5 — Station Information 2 — All Presets 6 — Direct Tune 3 — Seek Next 7 — Radio Band 4 — Audio Settings 8 — Seek Previous Store Radio Presets Manually The Radio stores up to 12 presets in each of the Radio modes.
Page 102 ELECTRONICS SiriusXM Premier Over 160 Channels Get every channel available on your satellite radio, and enjoy all you want, all in one place. Hear commercial-free music plus sports, news, talk and entertainment. Get all the pre- mium programming, including Howard Stern, every NFL game, Oprah Radio, every MLB and NHL game, every NASCAR race and more.
Page 103 ELECTRONICS Audio Jack (AUX) The AUX jack allows a portable device, such as an MP3 player or an iPod, to be plugged into the radio and utilize the vehicle’ s audio system, using a 3.5 mm audio cable, to am- plify the source and play through the vehicle speakers.
Page 104 ELECTRONICS PRE-DEFINED VOICE TEXT REPLY RESPONSES Yes. Stuck in traffic. See you later. Start without me. I’ll be late. Okay. Where are you? I will be <5, 10, 15, 20, 25, 30, 40, 45, 60>* minutes late. Call me. Are you there yet? I’ll call you later.
Page 105 ELECTRONICS UCONNECT 5.0 VOICE RECOGNITION QUICK TIPS Introducing Uconnect Start using Uconnect Voice Recognition with these helpful quick tips. It provides the key Voice Commands and tips you need to know to control your Uconnect 5.0 system. Key Features: • Five-inch Color Touchscreen Display with AM/FM/USB/Bluetooth •...
Page 106 ELECTRONICS Get Started 1. Visit UconnectPhone.com to check mobile device and feature compatibility and to find phone pairing instructions. 2. Reduce background noise. Wind and passenger conversations are examples of noise that may impact recognition. 3. Speak clearly at a normal pace and volume while facing straight ahead. The micro- phone is positioned on the rearview mirror and aimed at the driver.
Page 107 ELECTRONICS Basic Voice Commands The basic Voice Commands below can be given at any point while using your Uconnect system. . After the beep, say: Push the VR button • Cancel to stop a current voice session • Help to hear a list of suggested Voice Commands •...
Page 108 ELECTRONICS Radio Use your voice to quickly get to the AM, FM or SiriusXM Satellite Radio stations you would like to hear. (Subscription or included SiriusXM Satellite Radio trial required.) . After the beep, say: Push the VR button • Tune to ninety-five-point-five FM •...
Page 109 ELECTRONICS Media . After the beep, say one of the following commands and fol- Push the VR button low the prompts to switch your media source or choose an artist. • Change source to Bluetooth • Change source to iPod •...
Page 110 ELECTRONICS Phone Making and answering hands-free phone calls is easy with Uconnect. When the Phone- book button is illuminated on your touchscreen, your system is ready. U.S./Canadian residents can visit • UconnectPhone.com to check mobile device and feature compatibility and to find phone pairing instructions.
Page 111 ELECTRONICS Additional Information © 2016 FCA US LLC. All rights reserved. Mopar, Mopar Owner Connect and Uconnect are registered trademarks of FCA US LLC. Android is a trademark of Google Inc. SiriusXM and all related marks and logos are trademarks of SiriusXM Radio Inc.Yelp,Yelp logo, Yelp burst and related marks are registered trademarks of Yelp.
Page 112: Uconnect 6.5Nav
ELECTRONICS UCONNECT 6.5NAV Uconnect 6.5NAV Radio Buttons 1 — Display On/Off Control 6 — Uconnect PHONE Button 2 — Settings Button 7 — Uconnect Navigation (NAV) Button 3 — Back Button 8 — MEDIA Button 4 — BROWSE/ENTER Button — TUNE/ 9 —...
Page 113 ELECTRONICS • Press “+” or “–” next to Set Time Hours and Set Time Minutes to adjust the time. • If these features are not available, press “Off” for Sync with GPS. • Press “X” to exit out of the Clock Setting screen. Audio Setting •...
Page 114 ELECTRONICS Radio Uconnect 6.5NAV 1 — Radio Station Presets 6 — Direct Tune Radio Stations 2 — Toggle Presets 7 — Seek Previous 3 — HD Radio Available 8 — Browse/Manage Presets 4 — Audio Settings 9 — Radio Bands 5 —...
Page 115 ELECTRONICS Store Radio Presets Manually Your radio can store 36 total preset stations, 12 presets per band (AM, FM and SXM). They are shown at the top of your radio screen. To see the 12 preset stations per band, press the “Arrow” button on the touchscreen at the top right of the screen to toggle between the two sets of six presets.
Page 116 ELECTRONICS SiriusXM Parental Controls • You can skip or hide certain channels from view if you do not want access to them. Push the SETTINGS button on the faceplate, press the “SiriusXM Setup” button on the touchscreen, then select Channel Skip. Press the box, check-mark, next to the channel you want skipped.
Page 117 ELECTRONICS Replay Option Description Option Resumes playback of Live content at any time while replaying rewound Live content. • SiriusXM services require subscriptions, sold separately after the 12-month trial in- cluded with the new vehicle purchase. If you decide to continue your service at the end of your trial subscription, the plan you choose will automatically renew and bill at then-current rates until you call SiriusXM at 1-866-635-2349 for U.S.
Page 118 ELECTRONICS USB Port Connect your iPod or compatible device using a USB cable into the USB Port. USB Memory sticks with audio files can also be used. Then, audio from the device can be played on the vehicles sound system while providing metadata (artist, track title, album, etc.) information on the radio display.
Page 119 ELECTRONICS iPod/AUX Buttons 1 — Repeat Music Track 4 — Songs Currently In Queue 2 — Shuffle Music Tracks 5 — Browse Music 3 — Music Track Information 6 — Music Source • The USB/AUX controls are accessed by pressing the desired button on the touch- screen displayed on the side of the screen and choosing between AUX, USB or Bluetooth.
Page 120 ELECTRONICS Uconnect 6.5NAV Press the NAV button to access the Navigation feature. Changing The Navigation Voice Prompt Volume 1. Press the "Settings" button on the touchscreen from the Nav Main Menu. 2. In the Settings menu, press the “Guidance” button on the touchscreen. 3.
Page 121 ELECTRONICS Finding A Place By Spelling The Name 1. From the Main Navigation Menu, press the “Where to?” button on the touchscreen, press the “Points of Interest” button on the touchscreen and then press the “Spell Name” button on the touchscreen. 2.
Page 122 ELECTRONICS Go Home A Home location must be saved in the system. 1. From the Main Navigation menu, press the “Where To?” button on the touchscreen, then press the “Go Home” button on the touchscreen. 2. Your route is marked with a blue line on the map. If you depart from the original route, your route is recalculated.
Page 123 ELECTRONICS Adding A Stop To add a stop you must be navigating a route: 1. Press the “Menu” button on the touchscreen to return to the Main Navigation menu. 2. Press the “Where To?” button on the touchscreen, then search for the extra stop. When another location has been selected, you can choose to cancel your previous route, add as the first destination, or add as the last destination.
Page 124 ELECTRONICS Get Started 1. Visit UconnectPhone.com to check mobile device and feature compatibility and to find phone pairing instructions. 2. Reduce background noise. Wind and passenger conversations are examples of noise that may impact recognition. 3. Speak clearly at a normal pace and volume while facing straight ahead. The micro- phone is positioned on the rearview mirror and aimed at the driver.
Page 125 ELECTRONICS Basic Voice Commands The basic Voice Commands below can be given at any point while using your Uconnect system. . After the beep, say: Push the VR button • Cancel to stop a current voice session • Help to hear a list of suggested Voice Commands •...
Page 126 ELECTRONICS Radio Use your voice to quickly get to the AM, FM or SiriusXM Satellite Radio stations you would like to hear. (Subscription or included SiriusXM Satellite Radio trial required.) . After the beep, say: Push the VR button • Tune to ninety-five-point-five FM •...
Page 127 ELECTRONICS Media Uconnect offers connections via USB, Bluetooth and auxiliary ports (if equipped).Voice operation is only available for connected USB and iPod devices. . After the beep, say one of the following commands and fol- Push the VR button low the prompts to switch your media source or choose an artist. •...
Page 128 ELECTRONICS Phone Making and answering hands-free phone calls is easy with Uconnect. When the Phone- book button is illuminated on your touchscreen, your system is ready. U.S./Canadian residents can visit: • UconnectPhone.com to check mobile device and feature compatibility and to find phone pairing instructions.
Page 129 ELECTRONICS Navigation (Uconnect 6.5NAV) The Uconnect navigation feature helps you save time and become more productive when you know exactly how to get to where you want to go. . After the beep, say: 1. To enter a destination, push the VR button •...
Page 130 ELECTRONICS Push the VR button . After the beep, say one of the following commands: • Show fuel prices • Show 5 - day weather forecast • Show extended weather Traffic alerts are not accessible with Voice Command. SiriusXM Travel Link Additional Information ©...
Page 131: Uconnect Phone
ELECTRONICS UCONNECT PHONE Uconnect Phone (Bluetooth Hands Free Calling) Uconnect 5.0 Phone Menu 1 — Call/Redial/Hold 7 — Uconnect Phone Settings Menu 2 — Mobile Phone Signal Strength 8 — Text Messaging 3 — Currently Paired Mobile Phone 9 — Direct Dial Pad 4 —...
Page 132 ELECTRONICS Uconnect 6.5NAV Phone Menu 1 — Favorite Contacts 11 — Recent Call Log 2 — Mobile Phone Battery Life 12 — Browse Phone Book Entries (Con- 3 — Currently Paired Mobile Phone tains 911) 4 — Mobile Phone Signal Strength 13 —...
Page 133 ELECTRONICS • Most mobile phones/devices are compatible with the Uconnect system, however some mobile phones/devices may not be equipped with all of the required features to utilize all of the Uconnect system features. • For Uconnect Customer Care: • U.S. residents visit UconnectPhone.com or call 1-877-855-8400. •...
Page 134 ELECTRONICS Uconnect 6.5 NAV: 1. Place the ignition in the ACC or ON position. 2. Press the “Phone” button in the Menu Bar on the touchscreen. 3. Select “Settings.” 4. Select “Paired Phones.” 5. Select “Add device.” NOTE: Uconnect Phone will display an “In prog- Uconnect 6.5NAV ress”...
Page 135 ELECTRONICS Select The iPhone's Priority Level When the pairing process has successfully completed, the system will prompt you to choose whether or not this is your favorite mobile phone. Selecting “Yes” will make this mobile phone the highest priority. This mobile phone will take precedence over other paired mobile phones within range and will connect to the Uconnect system automati- cally when entering the vehicle.
Page 136 ELECTRONICS Select The Android Mobile Phone's Priority Level When the pairing process has successfully completed, the system will prompt you to choose whether or not this is your favorite mobile phone. Selecting “Yes” will make this mobile phone the highest priority. This mobile phone will take precedence over other paired mobile phones within range and will connect to the Uconnect system automati- cally when entering the vehicle.
Page 137 ELECTRONICS Voice Command Tips • Speaking complete names (i.e; Call John Doe vs. Call John) will result in greater system accuracy. • You can “link” commands together for faster results. Say “Call John Doe, mobile, ” for example. • If you are listening to available voice command options, you do not have to listen to the entire list.
Page 138 ELECTRONICS 3. Select located under DEVICES next to Uconnect. 4. Turn “Show Notifications” to On. Enable iPhone Incoming Text Messages Android Devices 1. Push the Menu button on the mobile phone. 2. Select Settings. 3. Select Connections. 4. Turn “Show Notifications” to On. NOTE: •...
Page 139 ELECTRONICS • All incoming text messages received during the current ignition cycle will be deleted from the Uconnect system when the ignition is turned to the Off position. Enable Android Device Incoming Text Messages Voice Text Reply (Not Compatible With iPhone) NOTE: Voice texting reply and voice texting features require a compatible mobile device enabled with Bluetooth Message Access Profile (MAP).
Page 140 ELECTRONICS Once your Uconnect system is paired with a compatible mobile device, the system can announce a new incoming text message, and read it to your over the vehicle audio sys- tem.You can reply to the message using Voice Recognition by selecting, or saying, one of the 18 pre-defined messages.
Page 141 ELECTRONICS Mobile Phone won’t pair to system: • Perform a hard reset in the mobile phone by removing the battery (if removable — see your mobile phone’ s owner manual). • Delete pairing history in mobile phone and Uconnect system; usually found in phone’ s Bluetooth connection settings.
Page 142: Steering Wheel Audio Controls
ELECTRONICS STEERING WHEEL AUDIO CONTROLS The steering wheel audio controls are located on the rear surface of the steering wheel. Right Switch • Push the switch up or down to increase or decrease the volume. • Push the button in the center to change modes AM/FM/SXM/AUX/USB or BTSA (Bluetooth Streaming Audio) —...
Page 143 ELECTRONICS • Push the back/left arrow button to access the information screens or submenu screens of a main menu item. • Push the OK button to access/select the information screens or submenu screens of a main menu item. Push and hold the OK button for two seconds to reset displayed/ selected features that can be reset.
Page 144: Programmable Features
ELECTRONICS PROGRAMMABLE FEATURES Uconnect Customer Programmable Features The Uconnect system allows you to access Customer Programmable feature settings such as Display, Units, Voice, Clock & Date, Safety & Driving Assistance, Lights, Doors & Locks, Engine Off Options, Audio, Phone/Bluetooth, SiriusXM Setup, Restore Default Settings and Clear Personal Data (Uconnect 6.5NAV) through buttons on the touchscreen.
Page 145: Power Outlet
ELECTRONICS POWER OUTLET There is one 12 Volt (13 Amp) power outlet in this vehicle, located under the HVAC controls. This power outlet can power mobile phones, electronics and other low power devices. • This power outlet is located in front of the gear selector. Power Outlet NOTE: •...
Page 146: Utility
UTILITY CARGO AREA FEATURES Cargo Load Floor — If Equipped The vehicle is equipped with a load floor that can be adjusted as needed. Position 1 (Floor Flush): This position allows you to make the load floor flat for ease of loading/unloading objects from the cargo area.
Page 147: Trailer Towing
UTILITY Anchoring Of The Load The cargo tie-downs, located on the trim panels around the cargo area floor, should be used to safely secure loads when the vehicle is moving. Cargo Box — If Equipped The cargo area contains a preformed cargo box that can be used for the storage of ob- jects that allows you to obtain a uniform level when loading.
Page 148: Recreational Towing (Behind Motorhome, Etc.)
UTILITY RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing This Vehicle Behind Another Vehicle TOWING WHEELS OFF THE FRONT WHEEL ALL-WHEEL DRIVE CONDITION GROUND DRIVE (FWD) (AWD) Flat Tow NONE NOT ALLOWED NOT ALLOWED REAR NOT ALLOWED NOT ALLOWED Dolly Tow FRONT NOT ALLOWED On Trailer BEST METHOD...
Page 149 UTILITY CAUTION! • DO NOT flat tow this vehicle. Damage to the drivetrain will result. If this vehicle requires towing, make sure the drive wheels are OFF the ground. • Ensure that the Electric Park Brake is released, and remains released, while being towed.
Page 150: What To Do In Emergencies
ROADSIDE ASSISTANCE • If your FIAT 500X requires jump start assistance, out of gas/fuel delivery, tire service, lockout service or towing due to a defect covered under the Basic Limited Warranty, dial toll-free 1-888-242-6342 or 1-800-363-4869 for Canadian Residents. See your Warranty booklet for further details.
Page 151 WHAT TO DO IN EMERGENCIES – Oil Pressure Warning Light This light indicates engine oil pressure sensor failure. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. A chime will sound for four minutes when this light turns on.
Page 152 WHAT TO DO IN EMERGENCIES — Tire Pressure Monitoring System (TPMS) Warning Light The warning light switches on and a message is displayed to indicate that the tire pres- sure is lower than the recommended value and/or that slow pressure loss is occurring. In these cases, optimal tire duration and fuel consumption may not be guaranteed.
Page 153 WHAT TO DO IN EMERGENCIES CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pres- sures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style.
Page 154 WHAT TO DO IN EMERGENCIES CAUTION! Continuous driving with the Transmission Temperature Warning Light illuminated will eventually cause severe transmission damage or transmission failure. – Seat Belt Reminder Light When the ignition switch is first turned to MAR/RUN, this light will turn on if the driver’ s seat belt is unbuckled, and a chime will sound.
Page 155 WHAT TO DO IN EMERGENCIES The light also will turn on when the parking brake is applied with the ignition switch in the MAR/RUN position. NOTE: This light shows only that the parking brake is applied. It does not show the degree of brake application.
Page 156 WHAT TO DO IN EMERGENCIES CAUTION! Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the engine control system. It also could affect fuel economy and driveability. If the MIL is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required.
Page 157 WHAT TO DO IN EMERGENCIES – Vehicle Security Light This light will flash rapidly for approximately 4 seconds when the vehicle security alarm is arming. The light will flash at a slower speed continuously after the alarm is set. The secu- rity light will also come on for about three seconds when the ignition is first turned on.
Page 158 WHAT TO DO IN EMERGENCIES – Oil Change Required Your vehicle is equipped with an engine oil change indicator system. The Oil Change tell- tale and message (Oil Change Required) will display in the instrument cluster display for approximately 5 seconds, after a single chime has sounded, to indicate the next scheduled oil change interval.
Page 159: If Your Engine Overheats
WHAT TO DO IN EMERGENCIES IF YOUR ENGINE OVERHEATS In any of the following situations, you can reduce the potential for overheating your en- gine by taking the appropriate action. • On the highways — slow down. • In city traffic — while stopped, put transmission in NEUTRAL, but do not increase en- gine idle speed.
Page 160: Tire Service Kit Storage
WHAT TO DO IN EMERGENCIES TIRE SERVICE KIT STORAGE The Tire Service Kit is located in the rear storage compartment inside a storage con- tainer. Located inside the container are a screwdriver and the emergency fuel funnel. To access the Tire Service Kit open the liftgate and remove the load floor. Tire Service Kit Location Tire Service Kit —...
Page 161 WHAT TO DO IN EMERGENCIES Remove the Tire Service Kit from the vehicle, take it out from the bag and place it near the punctured tire. Screw the clear flexible filling tube to the tire valve. WARNING! • Do not attempt to seal a tire on the side of the vehicle closest to traffic. Pull far enough off the road to avoid the danger of being hit when using the Tire Service Kit.
Page 162 WHAT TO DO IN EMERGENCIES WARNING! Tire Service Kit is not a permanent flat tire repair. Have the tire inspected and repaired or replaced after using Tire Service Kit. Do not exceed 65 mph (110 km/h) until the tire is repaired or replaced. Failure to follow this warning can result in injuries that are serious or fatal to you, your passengers, and others around you.
Page 163: Jacking And Tire Changing
WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING WARNING! • Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel.
Page 164 WHAT TO DO IN EMERGENCIES 2. Lift the access cover using the load floor handle. Load Floor Handle 3. Remove the fastener securing the spare tire. Spare Tire Fastener...
Page 165 WHAT TO DO IN EMERGENCIES 4. Remove the jack, wheel bolt wrench, and wheel chocks. 5. Remove the spare tire. Jack And Tools 1 — Jack 2 — Wheel Bolt Wrench 3 — Wheel Chock 4 — Emergency Funnel 5 — Screwdriver WARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the oc- cupants of the vehicle.
Page 166 WHAT TO DO IN EMERGENCIES Preparations For Jacking 1. Park the vehicle on a firm level surface as far from the edge of the roadway as pos- sible. Avoid icy or slippery areas. WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid being hit when operating the jack or changing the wheel.
Page 167 WHAT TO DO IN EMERGENCIES Jacking Instructions WARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as pos- sible before raising the vehicle.
Page 168 WHAT TO DO IN EMERGENCIES 3. Before raising the vehicle, use the wheel bolt wrench to loosen, but not remove the wheel bolts on the wheel with the flat tire. Turn the wheel bolts counterclockwise one turn while the wheel is still on the ground. 4.
Page 169 WHAT TO DO IN EMERGENCIES Front Jacking Location Front Jacking Engagement Point Rear Jacking Location Rear Jacking Engagement Point 5. Raise the vehicle just enough to remove the flat tire. WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it.
Page 170 WHAT TO DO IN EMERGENCIES CAUTION! Be sure to mount the spare tire with the valve stem facing outward. The vehicle could be damaged if the spare tire is mounted incorrectly. NOTE: • Your vehicle may be equipped with a compact spare tire or a limited —...
Page 171 WHAT TO DO IN EMERGENCIES WARNING! A loose tire or jack thrown forward in a collision or hard stop could endanger the oc- cupants of the vehicle. Always stow the jack parts and the spare tire in the places pro- vided.
Page 172: Jump Starting
WHAT TO DO IN EMERGENCIES JUMP STARTING If your vehicle has a discharged battery it can be jump-started using a set of jumper cables and a battery in another vehicle or by using a portable battery booster pack. Jump starting can be dangerous if done improperly so please follow the procedures in this sec- tion carefully.
Page 173 WHAT TO DO IN EMERGENCIES Preparations For Jump Start The battery in your vehicle is located in the front of the engine compartment, behind the left headlight assembly. NOTE: The positive battery post is covered with a protective cap. Lift up on the cap to gain access to the positive battery post.
Page 174 WHAT TO DO IN EMERGENCIES Proceed as follows: 1. Set the Electric Park Brake, shift the automatic transmission into PARK (manual trans- mission in NEUTRAL) and place the ignition OFF. 2. Turn off the heater, radio, and all unnecessary electrical accessories. 3.
Page 175 WHAT TO DO IN EMERGENCIES WARNING! Do not connect the jumper cable to the negative (-) post of the discharged battery. The resulting electrical spark could cause the battery to explode and could result in personal injury. Only use the specific ground point, do not use any other exposed metal parts.
Page 176: Freeing A Stuck Vehicle
WHAT TO DO IN EMERGENCIES FREEING A STUCK VEHICLE If your vehicle becomes stuck in mud, sand or snow, it can often be moved using a rock- ing motion. Turn the steering wheel right and left to clear the area around the front wheels.
Page 177: Tow Eye Usage - If Equipped
WHAT TO DO IN EMERGENCIES CAUTION! • Racing the engine or spinning the wheels may lead to transmission overheating and failure. Allow the engine to idle with the transmission in NEUTRAL for at least one minute after every five rocking-motion cycles. This will minimize overheating and reduce the risk of clutch or transmission failure during prolonged efforts to free a stuck vehicle.
Page 178 WHAT TO DO IN EMERGENCIES WARNING! Stand clear of vehicles when pulling with tow eyes. • Do not use a chain with a tow eye. Chains may break, causing serious injury or death. • Do not use a tow strap with a tow eye. Tow straps may break or become disen- gaged, causing serious injury or death.
Page 179 WHAT TO DO IN EMERGENCIES Front Tow Eye Installation The front tow eye receptacle is located behind a access door, located on the right front bumper fascia. To install the tow eye, open the access door using the vehicle key or a small screwdriver, and thread the tow eye into the receptacle.
Page 180: Gear Selector Override
WHAT TO DO IN EMERGENCIES GEAR SELECTOR OVERRIDE If a malfunction occurs and the gear selector cannot be moved out of the PARK position, you can use the following procedure to temporarily move the gear selector: 1. Turn the engine OFF. 2.
Page 181: Towing A Disabled Vehicle
WHAT TO DO IN EMERGENCIES TOWING A DISABLED VEHICLE This section describes procedures for towing a disabled vehicle using a commercial towing service. Wheels Towing OFF The FWD MODELS ALL WHEEL DRIVE Condition Ground Flat Tow NONE NOT ALLOWED NOT ALLOWED Rear NOT ALLOWED NOT ALLOWED...
Page 182 WHAT TO DO IN EMERGENCIES CAUTION! • Do not use sling type equipment when towing.Vehicle damage may occur. • When securing the vehicle to a flat bed truck, do not attach to front or rear sus- pension components. Damage to your vehicle may result from improper towing. Front Wheel Drive (FWD) Models The manufacturer recommends towing your vehicle with all four wheels OFF the ground using a flatbed.
Page 183: Enhanced Accident Response System (Ears)
WHAT TO DO IN EMERGENCIES ENHANCED ACCIDENT RESPONSE SYSTEM (EARS) This vehicle is equipped with an Enhanced Accident Response System. Please refer to “Occupant Restraint Systems” in “Getting Started” for further information on the Enhanced Accident Response System (EARS) function. EVENT DATA RECORDER (EDR) This vehicle is equipped with an Event Data Recorder (EDR).
Page 184: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE HOOD Opening The hood release lever (to open the primary latch) and safety latch (to open the second- ary latch) must be released to open the hood. 1. Pull the hood release lever located under the driver’ s side of the instrument panel. 2.
Page 185 MAINTAINING YOUR VEHICLE Closing 1. Hold up the hood with one hand and with the other hand remove the support rod from its seat and reinsert it into the locking tab. 2. Lower the hood to approximately 12 inches (30 cm) from the engine compartment and drop it.
Page 186: Engine Compartment - 1.4L Turbo
MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 1.4L TURBO 1. Engine Air Filter 2. Engine Oil Dipstick 3. Engine Oil Fill...
Page 187 MAINTAINING YOUR VEHICLE 4. Brake Fluid Reservoir 5. Battery 6. Power Distribution Center (Fuses) 7. Washer Fluid Reservoir 8. Engine Coolant Reservoir...
Page 188: Engine Compartment - 2.4L
MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 2.4L 1. Engine Air Filter 2. Engine Oil Dipstick 3. Engine Oil Fill...
Page 189 MAINTAINING YOUR VEHICLE 4. Brake Fluid Reservoir 5. Battery 6. Power Distribution Center (Fuses) 7. Washer Fluid Reservoir 8. Engine Coolant Reservoir...
Page 190: Fluid Capacities
MAINTAINING YOUR VEHICLE FLUID CAPACITIES Metric Fuel (Approximate) 1.4L Turbo/2.4L Engine 12.7 Gallons 48 Liters Engine Oil With Filter 1.4L Turbo Engine (SAE 5W-40 Synthetic, API Certified) 4.0 Quarts 3.8 Liters 2.4L Engine (SAE 0W-20, API Certified) 5.5 Quarts 5.2 Liters Cooling System * 1.4L Turbo Engine (MOPAR Antifreeze/Engine Coolant 10 Year/150,000 Mile Formula)
Page 191: Maintenance Procedures
MAINTAINING YOUR VEHICLE Chassis Component Fluid, Lubricant, or Genuine Part Manual Transmission – If Equipped We recommend you use MOPAR C Se- ries Manual & Dual Dry Clutch Transmis- sion Fluid. Automatic Transmission – If Equipped Use only MOPAR ZF 8&9 Speed ATF Au- tomatic Transmission Fluid, or equivalent.
Page 192: Maintenance Chart
MAINTAINING YOUR VEHICLE Your authorized dealer will reset the oil change indicator message after completing the scheduled oil change. If a scheduled oil change is performed by someone other than your authorized dealer, the message can be reset by referring to the steps described under “Instrument Cluster Display”...
Page 193 MAINTAINING YOUR VEHICLE...
Page 194 MAINTAINING YOUR VEHICLE...
Page 195 MAINTAINING YOUR VEHICLE...
Page 196 MAINTAINING YOUR VEHICLE...
Page 197: Fuses
MAINTAINING YOUR VEHICLE FUSES WARNING! • When replacing a blown fuse, always use an appropriate replacement fuse with the same amp rating as the original fuse. Never replace a fuse with another fuse of higher amp rating. Never replace a blown fuse with metal wires or any other material.
Page 198 MAINTAINING YOUR VEHICLE Cavity Maxi Fuse Cartage Fuse Mini Fuse Description 60 Amp Blue – – Module Body Computer, Rear Distribution Units – 20 Amp Blue – Controller Power Supply Body Computer – 30 Amp Pink – Brake Control Electronics Mod- 70 Amp Tan –...
Page 199 MAINTAINING YOUR VEHICLE Cavity Maxi Fuse Cartage Fuse Mini Fuse Description – – 20 Amp Yellow Power Outlet (Customer In- (Battery Pow- stalled) ered) – – 15 Amp Blue Electronic Unit Supply Automatic Transmission – – 30 Amp Green Heated Wind- shield –...
Page 200 MAINTAINING YOUR VEHICLE Cavity Mini Fuse Description 7.5 Amp BSM - Brake Control Module, EPS - Electric Power-Assisted Brown Steering 20 Amp Yellow Bi-directional Pump Washer 20 Amp Yellow Power Rear Window (Driver Side) 20 Amp Yellow Power Rear Window (Passenger Side) 7.5 Amp Supply ParkSense, Spot Lights Front Dome, Internal Electo- Brown...
Page 201: Adding Fuel
MAINTAINING YOUR VEHICLE ADDING FUEL The Capless Fuel System uses a flapper placed at the filler pipe of the fuel tank; it opens and closes automatically upon insertion/extraction of the fuel nozzle. The Capless Fuel System is designed so that it prevents the filling of an incorrect type of fuel.
Page 202 MAINTAINING YOUR VEHICLE Emergency Refueling Procedure If the vehicle is out of fuel, proceed as follows: 1. Open the liftgate and remove the emergency fuel fill funnel located in the cargo area. 2. Open the fuel door. 3. Insert the emergency fuel fill funnel in the filler pipe and proceed to fill the fuel tank. 4.
Page 203: Tire Safety Information
MAINTAINING YOUR VEHICLE Indiscriminate use of fuel system cleaning agents should be avoided. Many of these mate- rials intended for gum and varnish removal may contain active solvents or similar ingredi- ents. These can harm fuel system gasket and diaphragm materials. TIRE SAFETY INFORMATION Tire Markings NOTE:...
Page 204 MAINTAINING YOUR VEHICLE Tire Sizing Chart EXAMPLE: Example Size Designation: P215/65R15XL 95H, 215/65R15 96H, LT235/85R16C, T145/ 80D18 103M, 31x10.5 R15 LT P = Passenger car tire size based on U.S. design standards, or "..blank.." = Passenger car tire based on European design standards, or LT = Light truck tire based on U.S.
Page 205 MAINTAINING YOUR VEHICLE Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire; however, the date code may only be on one side. Tires with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire.
Page 206 MAINTAINING YOUR VEHICLE Tire Loading And Tire Pressure Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’ s side B-Pillar or the rear edge of the driver's side door. Check the inflation pressure of each tire, including the spare tire (if equipped), at least monthly and inflate to the recommended pressure for your vehicle.
Page 207 MAINTAINING YOUR VEHICLE WARNING! • Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recom- mended load capacity for your vehicle. Never overload them. • Improperly inflated tires are dangerous and can cause collisions. Under-inflation increases tire flexing and can result in over-heating and tire failure.
Page 208 MAINTAINING YOUR VEHICLE To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs” on the Tire and Loading Information placard. The combined weight of occupants, cargo/ luggage and trailer tongue weight (if applicable) should never exceed the weight refer- enced here.
Page 209 MAINTAINING YOUR VEHICLE WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load ca- pacity for your vehicle. Never overload them.
Page 210: Tires - General Information
MAINTAINING YOUR VEHICLE TIRES — GENERAL INFORMATION Spare Tires — If Equipped NOTE: For vehicles equipped with Tire Service Kit instead of a spare tire, please refer to the “Tire Service Kit” section located in your Owner’ s Information kit for further information. CAUTION! Because of the reduced ground clearance, do not take your vehicle through an auto- matic car wash with a compact or limited use temporary spare installed.
Page 211 MAINTAINING YOUR VEHICLE WARNING! Compact and Collapsible spares are for temporary emergency use only. With these spares, do not drive more than 50 mph (80 km/h). Temporary use spares have limited tread life. When the tread is worn to the tread wear indicators, the temporary use spare tire needs to be replaced.
Page 212 MAINTAINING YOUR VEHICLE Your wheels are susceptible to deterioration caused by salt, sodium chloride, magnesium chloride, calcium chloride, etc., and other road chemicals used to melt ice or control dust on dirt roads. Use a soft cloth or sponge and mild soap to wipe away promptly. Do not use harsh chemicals or a stiff brush.
Page 213: Department Of Transportation Uniform Tire Quality Grades
MAINTAINING YOUR VEHICLE Dark Vapor Or Black Satin Chrome Wheels CAUTION! If your vehicle is equipped with Dark Vapor or Black Satin Chrome wheels DO NOT USE wheel cleaners, abrasives or polishing compounds. They will permanently damage this finish and such damage is not covered by the New Vehicle Limited Warranty. USE ONLY MILD SOAP AND WATER WITH A SOFT CLOTH.
Page 214: Bulb Replacement
MAINTAINING YOUR VEHICLE Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat, when tested under controlled con- ditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
Page 215: Consumer Assistance
Booklet. United States customers may visit the Fiat Contact Us page at www.fiat.com scroll to the bottom of the page and select the “Contact Us” link, then select the “Owner’ s Manual and Glove Compartment Material” from the left menu.
Page 216: Reporting Safety Defects In The United States
CONSUMER ASSISTANCE • The Owner's Manual and User Guide electronic files are also available on the FIAT® website. • Click on the “For Owners” tab, select “Owner/Service Manuals”, then select your de- sired model year and vehicle from the drop down lists.
Page 217: Mopar® Accessories
MOPAR® ACCESSORIES AUTHENTIC ACCESSORIES BY MOPAR • The following highlights just some of the many Authentic FIAT Accessories by Mopar featuring a fit, finish, and functionality specifically for your FIAT 500X. • In choosing Authentic Accessories you gain far more than expressive style, pre-...
Page 218: Faq
How do I improve the Bluetooth performance of my Uconnect System? pg. 138 UTILITY How do I know how much I can tow with my FIAT 500X? pg. 145 How do I tow my FIAT 500X behind another vehicle? pg. 146 WHAT TO DO IN EMERGENCIES What do I do if my TPMS warning light is blinking? pg.
Page 219: Index
INDEX Adding Engine Coolant (Antifreeze) ..189 Brake System ....189 Adding Fuel....199 Fluid Check .
Page 220 INDEX Electronic Speed Control SET Jacking ....161 Indicator ....155 Jump Starting .
Page 221 INDEX Glass Cleaning ....189 Remote Control ... . .11 Hands-Free Phone (Uconnect) ..129 Lane Change And Turn Signals .
Page 222 INDEX Checking ....189 Restraint, Head ....49 Disposal ....189 Restraints, Child .
Page 223 INDEX Starting Trailer Towing ....145 Remote ....9 Trailer Towing Guide ... .145 Steering Trailer Weight .
Page 224 NOTES...
Page 225 NOTES...
Page 226 NOTES...
Page 227 This guide has been prepared to help you get quickly acquainted with your new FIAT vehicle and to provide a convenient reference ® source for common questions. However, it is not a substitute for your Owner’s Manual. For complete operational instructions, maintenance procedures and important safety messages, please consult your Owner’s Manual,...
Page 228 To get this app, go directly to the App Store or Google Play and enter the search keyword “MY FIAT” (U.S. market only). fiatusa.com/en/owners provides special offers tailored to your needs, customized vehicle galleries, personalized service records and more.

Fiat 500x User Manual

Introduction/Welcome

Controls at a Glance

Operating Your Vehicle

Electronics

Utility

What to Do in Emergencies

Maintaining Your Vehicle

Consumer Assistance

Mopar® Accessories

Faq

Index

Quick Links

Related Manuals for Fiat 500x

Summary of Contents for Fiat 500x

Table of Contents