Advertisement
TRIAD INSTALLATION GUIDE - 8×8 and 24×24 AUDIO MATRIX SWITCH
ADDING A 10×10 HDMI SWITCH TO A 24 SOURCE, 24 ZONE
SYSTEM
You can add audio from your HDMI sources to your 24-zone distributed
audio system using a Control 10×10 HDMI Matrix Switch (C4-LU1082D).
Repeat steps 1-3 in the 24 source, 24 zone system setup.
4 Connect eight stereo RCA cables from the RCA OUTPUTS of the HDMI
switch to the ANALOG AUDIO INPUTS on the audio matrix switch.
10x10 HDMI SWITCH
RCA connections to
audio matrix switch
EA-5
1
2
3
4
ETHERNET IN
SERIAL 1
OUT
ID
AC POWER:
WIFI 1
WIFI 2
100-240 V~
SERIAL 2
FACTORY
GIGABIT SWITCH
USB
E-SATA
60/50 Hz, 0.5 A
RESET
RCA connections
from HDMI matrix
External audio sources
switch
24x24 AMS
RCA connections to amplifier 2 RCA connections to amplifier 3
to amp 2
to amp 3
RCA connections to amplifier 1
8-ZONE AMP
(connect the rest of the 24 zone system as in the previous diagram)
Zones 1-8
8 pairs Triad
In-Ceiling
speakers
Connections from matrix switch to amplifier 2
8-ZONE AMP
12V
GLOBAL OUT
GLOBAL IN
AC POWER 100V-240V ~50-60Hz 105W
TRIGGER
1
2
3
4
5
6
7
IN
L
BRIDGE
BRIDGE
BRIDGE
BRIDGE
BRIDGE
BRIDGE
BRIDGE
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
OUT
R
FUSE RATING T6.3A_H 250V
CLIP
CLIP
CLIP
CLIP
CLIP
CLIP
CLIP
www.control4.com | 1-888-400-4072 | DOC-00287-A 2017-08-28 DH
Zones 9-16
TROUBLESHOOTING
RESETTING THE MATRIX SWITCH
• Network reset—Remove the power cord to power cycle the device.
Hold the ID button while you replace the power cord to power on the
matrix switch. Hold the ID button until you see Status LED show solid
orange.
• Factory restore—Press and hold the FACTORY RESTORE button for
five seconds to restore the device to its previous firmware image and
restore the defaults. The Status LED will blink white rapidly when the
factore restore begins.
Caution! The factory restore process will restore the matrix switch
to a factory state and replace the firmware image with the factory
default firmware.
LED TROUBLESHOOTING GUIDE
Status LED
1/ 3
3
5
7
IN 1
OUT 1
2/ 4
4
6
8
IN 2
OUT 2
IN 1
IN 2
OUT 1
OUT 2
ZIGBEE
IR / SERIAL
DIGITAL AUDIO
ANALOG AUDIO
External audio sources
REGULATORY/SAFETY INFORMATION
Amplifier 1
To review regulatory information for your particular Triad products, see the
information located on the Triad website at triadspkrs.co/reg.
WARRANTY
Speaker wires
Limited 2-year Warranty. Go to
Copyright ©2017, Control4 Corporation. All rights reserved. Control4, the Control4 logo, the 4-ball logo, 4Sight, Control My
Amplifier 2
Home, and Mockupancy are registered trademarks or trademarks of Control4 Corporation in the United States and/or other
countries. All other names and brands may be claimed as the property of their respective owners. All specifications subject
8
to change without notice.
L
BRIDGE
POWER MODE
1
2 3 4 5 6 7 8
ON
L
1
R
L
2
R
L
3
R
L
4
R
12V
GAIN
L
5
R
L
6
R
L
7
R
L
8
R
AUDIO
LINK TO GLOBAL INPUT
R
CLIP
ALL
2 3 4 5 6 7 8
Speaker wires
= solid
= flashing
Matrix switch is booting
Matrix switch finished booting and has IP address
Matrix switch is connected to Director
An audio output is active (white LED)
Matrix switch does not have an IP address
Firmware update in progress
Firmware update error
Factore restore in progress (flashing white LED)
triadspkrs.co/warranty
for details.
SPECIFICATIONS
AUDIO SPECIFICATIONS
THD
<0.005 %, 20 Hz – 20 kHz
Dynamic range
100 dB, A-weighted—input to output
SNR
>105 dB, A-weighted—input to output
Frequency response
20 Hz – 20 kHz +/- 0.2 dB
Input impedance
Minimum 12 K Ohms
Input voltage
2V RMS
Volume control per channel
0.5 dB steps, +0 to -80 dB range
Mute
Available on all outputs
Source input gain
0.5 dB steps, 0dB to +12dB on every input
Mono summing
Configurable per stereo output pair, each output combines the L/R
input signal.
5-band parametric EQ
Adjustable per stereo output. +/- 12 dB, 0.5 dB steps
Supported sample rates
44.1 kHz, 48 kHz, 96 kHz, 192 kHz—at 16- or 24-bit resolution
Tone control (bass/treble)
+/- 12 dB, 0.5 dB steps
Balance
Adjustable on each output—left 12 dB to right 12 dB
Loudness
Available on each output
Analog output voltage
2V RMS / 5V max
CONNECTIONS
8
8 AMS
×
Source inputs
8 × stereo analog (RCA)
(Digital inputs are either coax or
4 × digital coax
optical and are stereo PCM only)
4 × digital optical
Inputs 5-8 are either analog or
digital
Zone outputs
8 × stereo analog (RCA)
12V trigger outputs
2 × mono 3.5 mm outputs
Dimensions With Feet
2.14" x 17.33" x 9.84"
POWER
AC mains power
Universal 100 - 240VAC, 50 - 60 Hz, 10W (8 × 8), 20W (24 × 24)
Power connection
IEC 320 C13 power connector with 3-pole detachable power cord
THERMAL
Operating temperature
32 °F ~ 113 °F (0 °C ~ 45 °C)
Humidity
5% to 95% non-condensing
Storage
-4 °F ~ 158 °F (-20 °C ~ 70 °C)
Cooling method
Passively cooled-no fans
Thermal dissipation
1.32W / 4.5 BTU/hour (standby)
(heat losses)
7.09W / 24.2 BTU/hour
MISCELLANEOUS
8×8 AMS
Front power LED
1 × RGB status LED
System status LED
1 × RGB LED
Ethernet
1 × RJ-45
ID button
Yes
Factory restore button
Yes
Dimensions without feet
1.75 × 17.5 × 10.38"
(H × W × D)
(4.4 × 44.5 × 26.4 cm)
Dimensions with feet
2.13 × 17.5 × 10.38"
(H × W × D)
(5.4 × 44.5 × 26.4 cm)
PRODUCT NUMBER
8×8 AMS
TS-AMS8
24
24 AMS
×
16 × stereo analog (RCA)
8 × digital coax
8 × digital optical
24 × stereo analog (RCA)
4 × mono 3.5 mm outputs
3.89" x 17.33" x 9.84"
1.79W / 6.1 BTU/hour (standby)
15.22W / 52 BTU/hour
24×24 AMS
1 × RGB status LED
1 × RGB LED
1 × RJ-45
Yes
Yes
3.5 × 17.5 × 10.38"
(8.9 × 44.5 × 26.4 cm)
3.88 × 17.5 × 10.38"
(9.8 × 44.5 × 26.4 cm)
24×24 AMS
TS-AMS24
Advertisement
