Table of Contents
Advertisement
Quick Links
WA22AE
PNEUMATIC CRIMP TOOL
GENERAL SPECIFICATIONS
* Pneumatic Tools are designed with up to 8
die closures, changeable by a selector knob.
* The tool also has a full cycle ratcheting
control mechanism.
* Either the hand operated valve or the air
foot valve may be used.
pressure of the tool is 80-120 p.s.i.
recommended that each tool be set up with
a Regulator and Filter (WA27RF).
* All Crimp Tools, Positioning Heads, Bench
Mounts, Gages and Foot Valves must be
ordered separately by part number.
CRIMP TOOL
HAND VALVE
GAGING INSTRUCTIONS
A
"GO" GAGING
Operate tool to fully closed position.
gage end as shown.
between indenter tips.
GREEN
INDENTER
DANIELS MANUFACTURING CORP., 526 THORPE ROAD, ORLANDO, FL 32824, USA, PHONE 407 /855-6161, FAX 407 /855-6884
COPYRIGHT C) 2009 DANIELS MANUFACTURING CORP., USA.
REV. C
3/09
SEE PAGE 3 FOR IMPORTANT INFORMATION CONCERNING
Limited Warranty, AND LIMITATION OF LIABILITY.
The working
It is
BM-2 BENCH MOUNT
OPTIONAL)
(
DO NOT CRIMP G A GE!
G822
Insert "GO"
Gage must pass freely
SELECTOR
NO.
1
2
3
4
5
6
7
8
Length: 8"
Width: 2.25"
CRIMPING RANGE
See GAGING INSTRUCTIONS below.
ACCOMMODATIONS
Tool will accommodate all "K" series Positioners relating
to Daniels hand tool part numbers AFM8 and MH800.
FOOT VALVE OPERATION
Attach Foot Valve between air supply and tool air inlet.
Depress hand valve and lock in down position with
set screw (A) using 1 /16 hex Allen
CAUTION!
GAGE
PART NO.
G822
B
"NO-GO" GAGING
Operate tool to fully closed position.
gage end as shown.
the indenter opening, but must not pass c ompletely
through the opening.
±.0001
±.0001
A
B NO-GO DI A
GO DIA
.0070
.0090
.0095
.0115
.0120
.0140
.0170
.0150
.0180
.0200
.0225
.0250
.0260
.0285
.0305
.0330
WWW.DMCTOOLS.COM
E-MAIL: DMCOOMCTOOLS.COM
PAGE 1
..... DANIELS
,,,.
_,1/W'
11r1
DATASHEET
Weight: 2.21bs.
°
wrench.
WA10 FOOT VALVE
OPTIONAL)
(
\_ WA27RF
CUSTOMER
SUPPLIED
GO
NO-GO
B
A
DIA
DIA
.0305
.0330
The "NO GO" may partially enter
RED
INDENTER
ALL RIGHTS RESERVED.
MANUFACTURING
CORPORATION
AIR SUPPLY
OPTIONAL)
(
SELECTOR
NO.
8
Insert "NO GO"
WA22AE-DS
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for DMC WA22AE
Summary of Contents for DMC WA22AE
- Page 1 WA22AE ..DANIELS ,,,. MANUFACTURING _,1/W' 11r1 CORPORATION DATASHEET PNEUMATIC CRIMP TOOL SEE PAGE 3 FOR IMPORTANT INFORMATION CONCERNING LIMITED WARRANTY, AND LIMITATION OF LIABILITY. GENERAL SPECIFICATIONS Length: 8" Width: 2.25" Weight: 2.21bs. * Pneumatic Tools are designed with up to 8 die closures, changeable by a selector knob.
- Page 2 RELEASING A PARTIALLY CRIMPED CONTACT To release a partially crimped contact, proceed as follows: 1. Increase the air pressure to 120 p.s.i. and operate the unit. 2. If release has not been achieved after several attempts, contact DMC Service Department. PAGE 2...
- Page 3 DMC's option, the refund of the purchase price of any such product which proves defective in normal service within ninety (90) days after delivery to the first user, provided that the product is returned to DMC with all transportation charges prepaid and which shall appear to DMC's satisfaction, after DMC's inspection, to have been defective in material or workmanship, it being understood that DMC products are not consumer products.
Need help?
Do you have a question about the WA22AE and is the answer not in the manual?
Questions and answers