Tyco R/C Racing Batman Brave & Bold Electric Racing Set Instruction Manual

INSTRUCTION MANUAL

Keep these instructions for future reference,
as they contain important information.
WARNING:
CAUTION: This product contains a
!
CHOKING HAZARD – sharp edge(s). For adult assembly only.
Small parts.
Not for children under 3 years.
Take extra care during unpacking and
assembly.
START HERE!
ADULT ASSEMBLY REQUIRED.
Follow the step-by-step instructions to set up your race set.
Please separate the "Assembly Map" page, and keep it handy during assembly.
This page contains the contents list and large-scale Layout Drawings of the
fully-assembled track. You'll need to refer to it as you go.
The Assembly Map looks like this:
6
1
1 1
F
S
6" STRAIGHT
15" SQUEEZE
9" TERMINAL TRACK
9" RADIUS CURVE
12
8 1 1
CLIPS
GUARDRAILS
VEHICLE
VEHICLE
MAIN LAYOUT DRAWING of the assembled layouts.
Use either a diorama or a guardrail on the outside of the curves.
F
F
C
F
F S
1
A
1
F
F
1 = Beginner
2 = Average player
3 = Skilled player
Look for this symbol throughout this manual. It indicates important
information.
Be sure to check out the Troubleshooting Guide on the back of the
Assembly Map.
I. BASIC TRACK ASSEMBLY
Start out on a clean, hard, flat racing surface – not carpeting. Take out all
the track pieces (and other parts) and check them carefully against the
contents list on the Assembly Map.
This page shows the contents list and large-scale Layout
Drawings of the fully-assembled track (tracks are not drawn to scale).
You'll need to refer to it as you assemble your race set.
Refer to the Instruction Sheet for detailed step-by-step instructions
for setting up and using your race set.
1
2
BATTERY PACK
CONTROLLERS
1
2 1
1
SANDPAPER
CARD BOARD
Refer to the package
#2 SUPPORTS
for color photographs
ALTERNATE LA YOUT DRAWING
1
= TRACK SUPPORTS
= GUARDRAILS
R6940-0921
© 2009 Mattel, Inc. All Rights Reserved.
1. There are letters molded into each
track piece. These letters are used in
these instructions to indicate which
track piece goes where. Following the
layout drawings on the Assembly Map,
you may want to lay out your track –
without connecting any track pieces.
That way you'll be able to see how the
track layout goes together.
2. To connect track pieces: working on the flat surface, push the ends of the track
pieces together. Make sure they snap together securely – you'll hear a click when
they're properly connected.
Remember: if the track connections aren't right, electric power won't flow from
one track section to the next.
3. To disconnect track pieces, simply reach
underneath where the track pieces meet
and press the locking tabs together with
thumb and forefinger as shown.
Occasionally the metal track rails will stick up too far from the surface of a track
piece, as shown. This may interfere with vehicle movement. To correct, simply
press the rail back down with your finger. If the problem persists, please contact
Customer Service toll-free at 1-888-557-8926 (see hours of operation in the
Warranty section).
Sometimes brand-new track may need a quick cleaning for best performance.
Check the Maintenance section of this manual for more information.
II. DETAILED TRACK ASSEMBLY
a. Your race set makes two different layouts. Refer to the Assembly Map for detailed
track assembly. Start with the Terminal Track
continue adding track pieces until your layout is
complete.
b. Once your layout is assembled, you'll need to
add guardrails. Refer to the Assembly Map for
placement. To attach a guardrail: gently flex the
guardrail before attaching it. Carefully attach the
bottom of the guardrail first. Then pull up and snap
into place. Don't force guardrails into place.
5+
®
ASST. R6942
R6940-0920
and