Advertisement
Quick Links
Advertisement
Related Manuals for John Lewis SBSKITC
Summary of Contents for John Lewis SBSKITC
- Page 1 SBSKITC Side by Side Instruction manual...
- Page 2 Important information • Do not install the unit on your own or have unqualified personnel install it. • Improper installation may result in damage, malfunctioning or risk of electric shock. • This Side by Side unit must have the cooler section on the right side, the beverage storage section in the middle and the freezer section on the left side;...
-
Page 3: Tools Required For Installation
Tools required for installation (not supplied) - Page 7 • Carefully place the unit on the floor, following the instructions on the packaging to make sure the unit is facing upwards. • Open the bottom part of packaging and remove the corner protection. • Screw the M8 nuts (4) (bag 4) on the respective front feet , see Fig. (A). •...
- Page 8 • Glue two spacer spongers on the right side of the freezer. • Glue two spacer spongers on both sides of the wine cooler. • Glue two spacer spongers on the left side of the cooler. Use the distances indicated in the fig. under neath.
- Page 9 • Bring the wine cooler unit near to cooler unit. • If necessary adjust the front feet so that the units are both the same height, see Fig. (A). • Insert joining bracket (5), see Fig. (B). • Fix the joining bracket with four M5x18 screws (bag (2)), see Fig. (C).
- Page 10 • Repeat the operation between freezer unit and wine cooler unit. • If necessary adjust the front feet so that the units are both the same height, see Fig. (A). • Insert joining bracket (17), see Fig. (B). • Fix the joining bracket with four M5x18 screws (bag (2)), see Fig. (C).
- Page 11 • Fix the joining bracket (6) with four 4.2x13 self-tapping screws (3) (bag (3) using the holes in the top of the sides, see Fig. (A). • The bracket must be positioned so that the side of the bracket with the hole in the centre part protrudes as shown in fig.
- Page 12 • If it is necessary to amend the level of the doors (only cooler and freezer units), partially unscrew the hinge screws, related to the door to be adjusted, and move the hinge as indicated in the illustration below. • Repeat the operations for the cooler and freezer doors until a correct alignment is obtained.
- Page 13 • Before proceeding with the assembly of the top remove the protective film from the panel (7). • Position the top with the doors open so that the bottom front part fits under the top hinges., see Fig. (A) • Push the top so that its rear welt is touching the back of the units, see Fig. (B).
- Page 14 • Fix the top frontaly with three M5X12 screws (1) (bag (1), see Fig. (A). • Fix the back of the top with four 4.2x13 self-tapping screws (3) (bag (3), see Fig. (B).
- Page 15 • Fit the trims "11" between the units (freezer/wine cooler - wine cooler/cooler) by pressing along the entire profiles, see figure below.
- Page 16 • Before proceeding with the fixing of (9,10) side strips remove the protective film. • Insert the side strip, see fig. (A) • Align the outside of the side strip with the side of the unit and fix it with a 4.2x13 self-tapping screw (3) (bag (3)).
- Page 17 • Fit the handles of the three appliances, as shown in figures A, B and C. • The pivots and grub screws are included in the handle-kit. • Screw the two hexagonal head pivots (21), see Fig. (A). • Insert the handle holes in the pivots fixed on the door, see Fig. (B). •...
- Page 18 You should also ensure that air can circulate freely around the back and the top of the cabinet. Position the assembled Side by Side: • At least 150 mm from any overhanging kitchen furniture. • Install the appliance. • Inside the applaince you find two spacers (20) which must be fitted. Slacken the screws and insert the spacer under the screw head, then re-tighten the screws.
- Page 19 • After the positioning of the appliance, verify the right position with a level. • If necessary regulate the front feet to level the appliances. See Fig. (A) • Lock the M8 (4) nuts, see Fig. (B).
- Page 20 • Before proceeding with the fixing of the plinth (8) remove the protective film. • Fit the plinth (8) so that the inner hook couples with the joining bracket as shown in the illustration (see Fig. B).The plinth must be introduced under the wine cooler door stopper (see Fig.A). •...
- Page 24 John Lewis Partnership 171 Victoria Street London SW1E 5NN www.johnlewis.com 06/08 2221 055-70...