Related Manuals for xpr B100PROX-EH-SA v2
Summary of Contents for xpr B100PROX-EH-SA v2
- Page 1 B100PROX-EH-SA v2 B100PROX-MF-SA v2 Standalone Biometric Reader INSTALLER’S MANUAL...
-
Page 2: Table Of Contents
Contents .............. INTRODUCTION ..............MOUNTING ..............SPECIFICATIONS .............. APPLICATION DIAGRAM ........... RECOMMENDED SWIPING TECHNIQUE .............. INDICATION WIRING ..........................ADDING ADMIN FINGER ......PAIRING - BIOMETRIC READER AND REMOTE RELAY UNIT ............Pairing B100PROX-SA v2 with DINRTT ............Pairing B100PROX-SA v2 with RTT ............ -
Page 3: Mounting
(fitted with additional heater if very low temperature) to keep a constant sensor level performance. XPR™ cannot guarantee the functionality of the product if measures and advice before are not followed. -
Page 4: Specifications
SPECIFICATIONS Fingerprint Capacity: 98 templates Prox. cards Capacity: 2000 cards Card Type: EM or HID compatible (125KHz) - B100PROX-EH-SA or Mifare (13,56 Mhz; Classic 1K & 4K, Ultralight, Desfire) - B100PROX-MF-SA Output: 1 x Relay (2A/24V AC/DC) Push Button Input: Door Open Time: Pulse (1 to 30 seconds) or Toggle(ON/OFF) Entry Mode:... - Page 5 GND (PB) Violet Blue Green Orange Gray Yellow White 1N4001 Diode DIPSwitch settings Electric Strike Only in B100PROX-EH-SA v2 reader back view +12V Power Supply Dipswitch A: Card Type Relay (2A) TAMP TAMP ON: HID Push Button RS 485 Switch No. 2 Dipswitch A (sw.
-
Page 6: Recommended Swiping Technique
RECOMMENDED SWIPING TECHNIQUE Follow the below instructions for correct finger swiping. Starting from the first finger joint, place the selected finger on the swipe sensor and move it evenly towards oneself in one steady movement. Result: For a valid swipe: Tricolour Status LED turns green + OK Beep(short + long beep) For an invalid or misread swipe: Tricolour Status LED turns red + Error Beep ( 3 short beeps) INDICATION OK Beep... -
Page 7: Pairing - Biometric Reader And Remote Relay Unit
PAIRING - BIOMETRIC READER AND REMOTE RELAY UNIT If secure installation is needed, the reader can be connected to remote relay unit at secured area, which also can play the role of request-to-exit push button. Follow the instructions bellow to pair(couple) both devices or refer to the Remote Relay’s Manual. Pairing B100PROX-SA v2 with DINRTT 12 VDC DINRTT... -
Page 8: Administrator Programming
ADMINISTRATOR PROGRAMMING Use point fingers as Administrator and Installer. You can use the other fingers as access fingers. Administrator finger is enrolled at the end of the system installation. Initial enrollment of the Admin finger is described in installer manual. RIGHT LEFT ADD Finger Relay 1... -
Page 9: Delete Finger
DELETE Finger Action Finger Backlight Buzzer Sound short beep Swipe Admin Finger 4 times slow blinking short beep Wait 5 seconds (until fast blinking) Swipe User Finger fast blinking short + long beep fast blinking short + long beep Present card/tag 1 time DELETE ALL Fingers and Cards Action Finger... -
Page 10: Administrator Programming Block Diagram
Administrator Programming block diagram Swipe the ADMIN Finger 1 to 6 times depending of the desired menu swipe swipes swipes swipes swipes swipes Change Enroll ADD Finger ADD Finger ADD Finger ADMIN INSTALLER DELETE FINGER Relay 1&2 Relay 1 Relay 2 Finger Finger (on board) -
Page 11: Installer Programming
INSTALLER PROGRAMMING Set Relay 1 Time (on board) Action Finger Buzzer Sound Backlight Swipe Installer Finger 1 time short beep slow blinking short beep Wait 5 seconds (until fast blinking) Swipe the INSTALLER Finger beeps on 1 second fast blinking and start counting seconds Swipe the INSTALLER Finger to stop or wait 30 seconds to... -
Page 12: Installer Programming Block Diagram
Installer Programming block diagram Swipe the Installer Finger 1 to 4 times depending of the desired menu swipes swipe swipes swipes BACKLIGHT BUZZER RELAY 1 RELAY 2 ON/OFF ON/OFF Time Time (on board) (remote) Wait Wait Wait Wait 5 seconds 5 seconds 5 seconds 5 seconds...