Summary of Contents for Hanin HT100
- Page 1 Label Printer User Manual HT100 Xiamen Hanin Electronic Technology Co.,Ltd ADD: 5F, 8#, Aide Airport Industrial Park, Huli District, Xiamen ,China 361009 Tel.: +86-(0)592-5885993 Fax: +86-(0)592-5885992 Web: www.hprt.com...
-
Page 2: Table Of Contents
HT100 User Manual Contents Manual Information ............................... 2 Important Safety Instructions ..........................2 Chapter 1 Introduction ............................5 1.1 Packing List ................................. 5 1.2 Appearance and Components ..........................6 1.3 Dimension................................7 Chapter 2 Specifications ............................8 Chapter 3 Installation & Usage ..........................10 3.1 Media Loading .............................. - Page 3 Copyright This manual is printed in 2016, the copyright belongs to Xiamen Hanin Electronic Technology Co. Ltd. Printed in China 1.0 Version...
-
Page 4: Manual Information
HT100 User Manual Manual Information This User Manual contains basic information for product usage as well as for emergency measures that may be required. Provides information on utility usage for function selection, operating condition modification etc. Provides information on Seagull Windows Driver installation. -
Page 5: Important Safety Instructions
HT100 User Manual Important Safety Instructions Before using the appliance, please carefully read the following safety regulations in order to prevent any hazard or material damage. 1. Safety warning Warnings: The print head will become very hot during printing; avoid contact with the print head after printing has finished. - Page 6 HT100 User Manual Caution: Violating following instructions can cause slight wound or damage the appliance. 1) If you observe a strange smoke, odour or noise from the printer, unplug it before taking following measures. • Switch off the printer and unplug the set from the mains.
- Page 7 HT100 User Manual 4.WEEE (Waste Electrical and Electric Equipment) This mark shown on the product or its literature indicates that the corresponding item should not be discarded at the end of its working life with other household waste. To prevent possible harm to the environment or human health from...
-
Page 8: Chapter 1 Introduction
HT100 User Manual Chapter 1 Introduction 1.1 Packing List Notes: 1. Unpack the printer and keep the packing material in case you need to ship the printer in the future. 2. Make sure you own all parts as follows, if not, do contact the local dealer. -
Page 9: Appearance And Components
HT100 User Manual 1.2 Appearance and Components ￭ Front ￭ Rear ￭ Inside Rev. 1.0... -
Page 10: Dimension
HT100 User Manual 1.3 Dimension Rev. 1.0... -
Page 11: Chapter 2 Specifications
HT100 User Manual Chapter 2 Specifications (2/1) Items Parameter Printing Method Thermal Transfer/Direct Thermal Printing Resolution 203dpi(8dots/mm) Printing Speed Printing 127mm/s Max. Printing Width 108mm Max. Printing Length 15mm - 1200mm 32 bit RISC CPU Processor 32MB Memory 16MB Flash... - Page 12 HT100 User Manual (2/2) Items Parameter AC/DC switching power adapter Power I/P: AC100-240V, 50/60Hz, O/P: DC 24V/2A, peak 5A Operation 41℉(5℃)-104℉(40℃)，30%-85%(non-condensing) Environment Storage -4℉(-20℃)-122℉(50℃)，10%-90%(non-condensing) Dimension(L*H *W) 240*172.5*198mm Physical Characteristics Weight 2.26kg(excluding consumables) Options & Accessories External label roll holder for 8’’ (203mm) OD label rolls...
-
Page 13: Chapter 3 Installation & Usage
HT100 User Manual Chapter 3 Installation & Usage 3.1 Media Loading 3.1.1 Paper Roll Loading 1. Pull forward the left and right cover open lever with both hands simultaneously and lift up the printer cover. 2. Slide the paper holders to adjust the distance between them, place paper roll into the holders, adjust paper roll holders according to paper roll’s width.(Make sure the locking tab is un-lock, so... - Page 14 HT100 User Manual 3. Make sure the holders are snug against the sides of the media roll, and then press the locking tab down to lock the media holders in place. 4. Pull some paper out and pass it through paper guides, adjust paper guides according to the...
- Page 15 HT100 User Manual 5. Hold the printer cover while press the kick-stand cover lock in the direction of arrow. 6. Lower the printer cover, press down until the cover snap close, and tear the extra paper in the direction of printer.
- Page 16 HT100 User Manual 3.1.2 External Paper Roll Loading If the paper roll is extremely large, users can load the paper roll outside(See the graph at right). Pass the paper through the external feed slot and then through paper guides. Adjust...
- Page 17 HT100 User Manual 2. Put the new ribbon into the supply spindles, and the bare core into the take-up spindles. 3. Pull some ribbon out, pass it through the printing head. Stick the ribbon to the bare core. Use the adhesive strip on the new rolls, otherwise, use tape.
- Page 18 HT100 User Manual 5. Close the printer cover and printing head module will automatically fold up, until you hear a sound. Rev. 1.0...
-
Page 19: Power Connection
HT100 User Manual 3.2 Power Connection 1. Make sure the printer is “OFF” 2. Connect the AC adapter with power interface. 3. Connect the AC adapter with power cord. 4. Plug the other side of power cord into the socket outlet. -
Page 20: Peripherals Connection
Detailed pairing methods, please refer to primary devices Bluetooth Names. After pairing, primary devices with virtual Bluetooth interface (smart phone , pocket PC, palm, notebook) can drive mobile thermal printer HT100 to printer through such virtual Bluetooth interface. Rev. 1.0... -
Page 21: Detection
HT100 User Manual 3.4 Detection Rev. 1.0... -
Page 22: Control Panel
HT100 User Manual 3.5 Control Panel FEED Button When the printer is on, press this button, printer will automatically feed a label under “Label Mode”; the printer will feed a fixed distance under “Continuous Mode”; When the printer is printing, press this button, current printing job pauses, and the LED indicator is white(tri-color blue, green, red);... - Page 23 HT100 User Manual 3.6.3 Quick Calibration Note : Users must carry out the calibration under those conditions below: The first time to use the printer since installation; The first time to use the printer since sensor cleaning; ...
- Page 24 HT100 User Manual 3.6.4 Print Self-test Page The self-test checks the printer’s current settings, status and whether the printer has any problem. 1. Print Self-test Page Manually 1.Make sure paper is loading properly. 2.Make sure the printer is off and top cover closes properly. .
-
Page 25: Chapter 4 Interface
HT100 User Manual Chapter 4 Interface 4.1 USB Interface Figure 4-1 SIGNAL NAME VBUS 4.2 Other Optional Interface Serial Port Figure 4-2 SIGNAL NAME Rev. 1.0... - Page 26 HT100 User Manual Ethernet Port SIGNAL NAME Rev. 1.0...
-
Page 27: Chapter 5 Maintenance & Adjustment
HT100 User Manual Chapter 5 Maintenance & Adjustment Adhesives and coatings of the media can transfer onto the printer parts over time along the media path including the thermal print head and media sensor. This build-up can accumulate dust and debris. Failure to clean the print head, media path, and media sensor could result in print quality, worst more of inadvertent loss off labels, label jams and possible damage to the printer. -
Page 28: Chapter 6 Label Printer Utility Instructions
HT100 User Manual Chapter 6 Label Printer Utility Instructions 6.1 Installation Preparation Download HPRTUtilityLabel application program. 6.2 Usage (1).Install “HPRTUtilityLabel V2.0.0.0.exe” and then open the “HPRTUtility”. Here is the windows(The screen may vary slightly by different operating systems and models). - Page 29 HT100 User Manual ●Click “Add Printer” choose the printer and port, click “OK” add successful, check in “Printer List”. ●Click “Modify Printer” choose the printer and port, click “OK” modify successful. Rev. 1.0...
- Page 30 HT100 User Manual ●Click “Delete Printer”, click “OK” delete the printer you chosen, click “Cancel” cancel delete printer. ●Choose the printer you currently use, connect it with computer; Click “Connect Test” to test whether the connection is ok or not.
- Page 31 HT100 User Manual (3).Function. ●Click “Printer Information”, shows printer information.(Differ from your printer) ●Click “Print Test Text”, type the text you need to print→ Set up the printing range(printable width & height)→Click “Print” printer start to print printer test text.
- Page 32 HT100 User Manual ●Click “Parameter Setting”. 1) COM Port Setting: Baud Rate: Parity: Stop BitS: 2)Language: Rev. 1.0...
- Page 33 HT100 User Manual International character: Codepage: 3)Label paper automatic position when power on: 4) Select small label (Label length less than 20mm): 5)Print type: 6)Print when error: 7)Display “Reprint” when reprint: 8) After stopping X mins, enable the anti-adhesive paper function: choose range:0~255 Rev.
- Page 34 HT100 User Manual 9) Print density (1:Washiest): choose range:0~15 10) Ethernet Setting: 11) Other: Judge Paper Mode(Label, Receipt, BlackMark): Max Mark Length(choose range:0~500mm): Min label length(choose range:0~500mm): Max label length(choose range:0~500mm): Heat Adjust: Rev. 1.0...
- Page 35 HT100 User Manual Print Speed(choose range:2,3,4,5): 9)Click “Set” save all the above settings, click “ok” back to the main menu. Click “Close” back to the main menu and all the settings canceled. ●Click “Restore Factory Settings”, click “OK” printer restore factory settings, click “Cancel” cancel restore factory settings.
-
Page 36: Chapter 7 Seagull Windows Driver Installation
HT100 User Manual Chapter 7 Seagull Windows Driver Installation 7.1 Introduction This chapter provides information on installation according to PC operating system (OS). This driver support for these following operating systems: Microsoft Windows 10 (32 bit/64 bit) Microsoft Windows 8 (32 bit/64 bit) -
Page 37: Installation
7.3 Installation Warning: Under different operating system, the screen has slight difference. Please operate it according to the tips. Take HPRT HT100 (Windows XP)as example. Recommend to close security software before installation in case of preventing installation. 1.Select one interface to connect your printer to computer. - Page 38 HT100 User Manual 5.Select a directory on the computer to unpack the driver or accept the default location then click “Next”. 6.Click"Finish". Rev. 1.0...
- Page 39 HT100 User Manual 7.Select "Install printer drivers" then click "Next". Note: Connect your printer to computer, can automatically detect and install.(Take USB for example) 8.Select "Install a driver for a Plug and Play printer, click "Next". Rev. 1.0...
- Page 40 HT100 User Manual 9.Enter a name for this printer, click "Next". 10.Click"Finish". Rev. 1.0...
- Page 41 HT100 User Manual 11.Click "Close", the HPRT HT100 Label printer driver installed successfully. 12.After installation, the icon will be found in ”Start”→“Printers and Faxes”. Note: 1.If you already installed the driver (No matter what kind of port), when you connect the printer with computer, it will create a USB port automatically.
-
Page 42: Chapter 8 Bartender® Ultralite Installation
HT100 User Manual Chapter 8 BarTender® Ultralite Installation 8.1 Introduction This chapter provides information on BarTender® installation according to PC operating systems(OS). This label design software is available in two versions:32-bit and 64-bit. 8.2 Installation Preparation Download BarTender® application program. -
Page 43: Installation
HT100 User Manual 8.3 Installation Note：Under different operating system, the screen has slight difference. Please operate it according to the tips. Take Windows 7 as example.(Recommend to close security software before installation in case of preventing installation) 。 1.Double click application program 2.Select language, then click "OK"。... - Page 44 HT100 User Manual 4.Read and accept the license agreement, then click "Next"。 5.Select "Features" and "Installation Location" then click "Next". Rev. 1.0...
- Page 45 HT100 User Manual 6.Click "Installation"。 7.If occurs following windows, please choose "Allow this operation", or you may close security software before installation in case of preventing installation. Rev. 1.0...
- Page 46 HT100 User Manual 8.Click "Finish"。 9. Select the edition you need（can be changed according to your need while using）,then click "OK". Rev. 1.0...
- Page 47 HT100 User Manual 10.Click "Close", BarTender® installed successfully。 11.Back to desktop, you may see BarTender® icon,dobule click it get down to use. Rev. 1.0...