Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Progress Lighting AirPro P2542
Summary of Contents for Progress Lighting AirPro P2542
- Page 1 ® P2542...
- Page 2 Limited Lifetime Warranty Date Purchased Progress Lighting fan motors are warranted to the original purchaser to be free of electrical and/or mechanical defects for so long as the original purchaser owns the fan. Store Purchased Pull chain switches, reverse switches, capacitors and metal finishes are warranted for a period of 1 year.
-
Page 3: Table Of Contents
Safety Rules Unpacking Your Fan Installing Your Fan Making the Electrical Connections Operating Your Fan Care of Your Fan Troubleshooting Specifications Table of Contents... -
Page 4: Safety Rules
READ AND SAVE THESE INSTRUCTIONS Avoid placing objects in path of the blades. To reduce the risk of electric shock, insure electricity has been turned off at the circuit breaker or fuse box To avoid personal injury or damage to the fan and other before beginning. -
Page 5: Unpacking Your Fan
Unpack your fan and check the contents. You should have the following items: Blade attachment hardware 1. Mounting Bracket (inside canopy) 5. Fan Motor Assembly (13 Screws) 2. 6” Ball/Downrod Assembly (hanger pin 6. Blades (4) Electrical hardware and Balancing kit and locking pin pre-attached) 7. -
Page 6: Installing Your Fan
Tools Required Figures 1, 2, and 3 are examples of different ways to mount the electrical box. Phillips screw driver or straight slotted screw driver, adjustable wrench, step ladder, and wire cutters. Figure 3 Mounting Options Note: You may need a longer downrod to maintain proper blade clearance when installing If there isn’t an existing electrical box, then on a steep, sloped ceiling. -
Page 7: Hanging The Fan
Hanging the Fan 7. Re-tighten the set screws on the collar on Turn Canopy bottom cover to Remove top of the motor housing. REMEMBER to turn off the power. Follow Canopy 8. Make sure the grommet is properly installed the steps below to hang your fan properly. in the collar cover, then slide the collar cover on the downrod until it rests on the motor NOTE: This fan is recommended for... - Page 8 Installing Fan to the Electrical Box UL Listed Electrical Ceiling WHEN MOUNTING THE FAN ON A SLOPED Mounting CEILING, THE STANDARD BALL/DOWNROD Bracket MOUNTING METHOD MUST BE USED. THE Washers MOUNTING PLATE MUST BE MOUNTED SO Hook Mounting THAT THE SLOT OPENINGS ARE ON THE screws 120V Wires LOWER SIDE BY SLIDING THE MOUNTING...
-
Page 9: Making The Electrical Connections
Making the Electrical 5. Connect the receiver black wire to the SUPPLY CIRCUIT supply black (hot) wire using a wire nut Connections (Figure 10). 6. Connect the receiver white wire to the REMEMBER to disconnect the power. If supply white (neutral) wire using a wire nut you feel you do not have enough electrical Remote (Figure 10). - Page 10 Finishing the Fan 3. Make sure that canopy is tightened securely the wood screw and then tighten the screw firmly, Installation to ceiling mounting bracket and that the or connect the safety cable directly to the outer joist. ceiling mounting bracket is tightened Attaching the Fan securely to the electrical box.
-
Page 11: Installing The Light Kit
Installing the Light Kit 4. Push the light kit fitter assembly up so that the two loosened screw heads fit into Pan/Light Kit Fitter the keyhole slots. Turn the light kit fitter Assembly/ Shatter- assembly clockwise, tighten the screws. Re- install the screw that was removed in step 3 Resistant Bowl and tighten frmly. -
Page 12: Operating Your Fan
Speed settings for warm or cool weather depend on factors such as room size, ceiling height, number of fans, and so on. The fan shipped from the factory with the reversing switch positioned to circulate air Warm weather - (Forward) A downward air downward. -
Page 13: Care Of Your Fan
Troubleshooting Care of Your Fan Here are some suggestions to help you Problem Solution maintain your fan. Check main and branch circuit fuses or breakers Fan will not start 1. Because of the fan’s natural movement, Check line wire connections to the fan and switch wire connections in some connections may become loose. -
Page 14: Specifications
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. ©2017 Progress Lighting, Inc. 701 Millennium Blvd.,...