SERVICE MANUAL DVD RW/VCR-RECORDER C O N T E N T S Specifications ---------------------------------------- 2 Disassembly ------------------------------------------- 6 Principal Parts Location -------------------------- 7 Troubleshooting ------------------------------------- 8 Electrical Parts List -------------------------------- 11 IC Internal Diagrams ----------------------------- 58 IC and Transistor Voltage Chart ------------- 90 ---------------------------------- 98 VCR Mechanism...
Page 3
SAFETY PRECAUTIONS ANY MEASUREMENTS NOT WITHIN THE LIMITS OUTLINED ABOVE ARE INDICATIVE OF A POTEN- The following check should be performed for the continued TIAL SHOCK HAZARD AND MUST BE CORRECTED protection of the customer and service technician. BEFORE RETURNING THE APPLIANCE TO THE CUS- TOMER.
LASER BEAM SAFETY PRECAUTIONS CLASS 1 LASER PRODUCT DANGER INVISIBLE LASER RADIATION AVOID DIRECT EXPOSURE TO BEAM Do not look directly at the laser beam coming from the pickup or allow it to strike against your skin. This Receiver uses a pickup that emits a laser beam. The laser beam is emitted from the location shown in the figure.
Page 5
HANDLING LASER PICKUP The laser diode in the optical system of this receiver can be damaged by electrostatic discharge from clothes, body, etc. Proper electrostatic grounding for service personnel is required during servicing. BEFORE REPAIRING THE DVD MECHANISM a. Human Body Grounding: Many of the components used in this compact disc player, including the laser pickup, are sensitive to electrostatic dis- charge.
TROUBLESHOOTING Symptom Cause Remedy No power. The power cord is disconnected. Plug the power cord into the wall outlet securely. The power is on, but Insert a disc.(Check that the DVD or audio CD indicator the DVD player No disc is inserted. in the DVD display is lit.) does not work.
Page 9
Symptom Cause Remedy The disc is not writable DVD DISC. Remove the disc and insert a proper writable DVD DISC. Only DVD+R/+RW/-R/-RW DISC can be recorded. Remove The disc is CD-R/RW. the disc and insert a proper writable DVD DISC. Recording does The disc is full.
TEST MODE TEST Mode shows the infomation as follows. I. Back End Version (It is to express each Buyer, each model, and version number.) II. Front End Version (It is to display the Mecha Fimware version number.) III. Back End Build time (It can be used to seperate each B/E firmware version by the day.) IV.
RESISTORS AND CAPACITORS Notes. * Circuit No's first character indicates kinds of part type. C : Capacitors R : Resistors D : Diode J : Jumper L : Coil Q : Transistors S : Switch BK : Bracket JK : Jack IC : Integrated Circuit X : Crystal BD : Bead...
DVD PART SEQ. PART NO. DESCRIPTION SPECIFICATION REMARKS CIP11741B FRONT PCB AUTO ASS'Y QRW-6500 CUP11741Z PCB , FRONT QRW-6500 C501 HCBS1H103ZFT CAP , CERAMIC 0.01UF 50V Z C502 CCEA1CKS470T CAP, ELECT 47UF/16V/5MM HEIGHT 00107-1051 C503 CCEA1CKS101T CAP , ELECT C504 HCBS1H103ZFT CAP , CERAMIC 0.01UF 50V Z...
Page 44
VCR PART SEQ. PART NO. DESCRIPTION SPECIFICATION REMARKS CHG1A243 CUSHION CIP11744B VCR MAIN PCB AUTO ASS'Y (EUR) QRW-6500 CUP11744Z PCB , VCR MAIN QRW-6500 C007 HCBS1H471KBT CAP , CERAMIC C008 CCKT1H152KB CAP , CERAMIC 1500PF 550V KB C009 CCEA1CH100T CAP, ELE 10UF/16V/-40~+86 00107-1027 C010 CCEA1CH100T...
Page 45
SEQ. PART NO. DESCRIPTION SPECIFICATION REMARKS C228 CCEA1HKS1R0T CAP, ELE 1UF/50V/5MM HEIGHT 00107-0029 C229 HCBS1H473ZFT CAP , CERAMIC 0.047UF 50V Z C230 HCBS1H223ZFT CAP , CERAMIC 0.022UF 50V Z C231 HCBS1H104ZFT CAP , CERAMIC 0.1UF 50V Z C232 HCBS1H473ZFT CAP , CERAMIC 0.047UF 50V Z C233 HCBS1H223ZFT...
Page 46
SEQ. PART NO. DESCRIPTION SPECIFICATION REMARKS C320 HCBS1H101KBT CAP , CERAMIC 100PF 50V K C321 CCEA1CKS470T CAP, ELECT 47UF/16V/5MM HEIGHT 00107-1051 C322 HCBS1H103ZFT CAP , CERAMIC 0.01UF 50V Z C323 CCEA1HKS1R0T CAP, ELE 1UF/50V/5MM HEIGHT 00107-0029 C324 HCBS1H180JT CAP , CERAMIC C325 HCBS1H180JT CAP , CERAMIC...
Page 47
SEQ. PART NO. DESCRIPTION SPECIFICATION REMARKS C828 CCEA1CH101T CAP, ELE 100UF/16V/-40~+85 00107-1003 C830 CCEA1EH101T CAP , ELECT 100UF 25V C912 CCEA1CH100T CAP, ELE 10UF/16V/-40~+86 00107-1027 C913 HCQI1H682JZT CAP , MYLAR 6800PF 50V J C914 CCEA1CH470T CAP, ELE 47UF/16V/-40~+85 00107-1007 C915 CCEA1CH470T CAP, ELE 47UF/16V/-40~+85 00107-1007...
IC INTERNAL DIAGRAMS I.C PIN DESCRIPTIONS (FIP DRIVER : LC75725E) : IC52 Function PIN No PIN Name Driver block power supply connection.(Both pins must be conneted) 1,13 Logic block power supply connection. Provide a voltage between 4.5 and5.5V Power supply connection. Connect to the ground OSCI Osillator connection.
Page 59
I.C PIN DESCRIPTIONS (FLASH U-COM : ST92F124V1) : IC14 Function PIN No PIN Name No Connection PWR_ON Relay ON/OFF Control Port No Connection VCR ON/OFF Control Port VCR_ON UPDATE_CLK UPDATE_DATA IN1 Host Update Port UPDATE_DATA IN2 UPDATE_DATA IN3 No Connection No Connection No Connection TC9164 STB_OUT...
Page 60
SW11 Digital Interface (u-COM<-->NJU3715) GND Port Power Supply Port Digital Interface (u-COM<-->NJU3715) REMOTE Input Port REM_IN Chip ENABLE Input Port CE-ENABLE_IN No Connection DVD-MREQ_IN DVD Interface Port No Connection KEY2_IN Front Panel Key Control Port KEY1_IN VFO-CE VFD-DATA FIP DISPLAY Control Port VFD-CLK VFD-BLK STBY-LED_ON Control Port...
Page 63
I.C PIN DESCRIPTIONS (D/A CONVERTER : PCM1754) : IC29 Function PIN No PIN Name Audio-data bit-clock input DATA Audio-data digital input LRCK L-channel and R-channel audio data latch enable input Digital ground DGND No Connection Analog power supply 5V VOUTL Analog output for L-channel Analog output for R-channel VOUTR...
Page 64
PIN ASSIGNMENTS PCM1754 (TOP VIEW) DATA LRCK MUTE DGND DEMP TEST ZEROA AGND BLOCK DIAGRAM Audio LRCK Serial Output Amp DATA Port Low-Pass Filter 4y/8y Oversampling Enhanced Digital Multilevel Filter (FMT) ML Delta-Sigma Modulator Function Serial Control (MUTE) MC Control Output Amp Port (DEMP) MD...
Page 65
I.C PIN DESCRIPTIONS (3CH VIDEO AMPLIFIER : NJM2580) : IC34, 35 Function PIN No PIN Name VIN1 GND1 VIN2 GND2 VIN3 GND3 H : Power Save → OFF L : Power Save → ON Power Save OPEN : Power Save → ON VSAG VOUT VOUT3...
Page 66
I.C PIN DESCRIPTIONS (VIDEO SW : NJM2296) : IC79, 80 Function PIN No PIN Name OUTPUT VIDEO SIGNAL VOUT 1 SW 5 SWITCH FOR SELECT SIGNAL VIN 5 INPUT VIDEO SIGNAL SWITCH FOR SELECT SIGNAL SW 3 INPUT VIDEO SIGNAL VIN 4 SWITCH FOR SELECT SIGNAL SW 4...
Page 67
I.C PIN DESCRIPTIONS (VIDEO SW : NJM2244) : IC81, 82 Function PIN No PIN Name INPUT VIDEO SIGNAL VIN1 SWITCH FOR SELECT SIGNAL VIN2 INPUT VIDEO SIGNAL SWITCH FOR SELECT SIGNAL INPUT VIDEO SIGNAL VIN3 Supply voltage VOUT 1 OUTPUT VIDEO SIGNAL Ground PIN ASSIGNMENTS NJM2244M...
Page 68
I.C PIN DESCRIPTIONS (S-VIDEO COMPOSITE SW : BA7607F) : IC27 Function PIN No PIN Name INPUT VIDEO SIGNAL IN2 a CTL A SWITCH FOR SELECT SIGNAL OUT a OUTPUT VIDEO SIGNAL Ground Port OUTPUT VIDEO SIGNAL OUT b OUTPUT VIDEO SIGNAL OUT c CTL C SWITCH FOR SELECT SIGNAL...
Page 69
I.C PIN DESCRIPTIONS (A/D CONVERTER : AK5381VT ) : IC24 Function PIN No PIN Name Rch Analog Input Pin AINR AINL Lch Analog Input Pin CKS1 Mode Select 1 Pin Common Voltage Output Pin, VA/2 VCOM Analog Ground Pin AGND Analog Power Supply Pin, 4.5 ~ 5.5V Digital Power Supply Pin, 2.7 ~ 5.5V(fs=4k ~ 48kHz), 3.0 ~ 5.5V(fs=48k ~96kHz) Digital Ground Pin...
Page 71
I.C PIN DESCRIPTIONS (AMPLIFIER : NJM2068M) : IC31,53,62,63,64,66,67,70,71,73,75,96,97) Function PIN No PIN Name A OUTPUT A OUTPUT A -INPUT A -INPUT A +INPUT A +INPUT B +INPUT B +INPUT B -INPUT B -INPUT B OUTPUT B OUTPUT PIN ASSIGNMENTS NJM2068M - 71 -...
Page 75
IC INTERNAL DIAGRAMS ( VCR PART ) MICOM (M37762MCA-xxxGP : IC31) PIN DESCRIPTIONS PIN No. Port Pin Name DESCRIPTION ACTIVE P11/AN8 ST SENEOR TAPE START SENSOR DATA INPUT P77/AN7 OPTION P76/AN6 CAP F/R(H) CAPSTAN MOTOR FWD/RVS H/L P75/AN5 POWER FAIL POWER FAIL PORT LOW P74/AN4 PG DELAY...
Page 76
PIN No. Port Pin Name DESCRIPTION ACTIVE VCC +5V X IN OSC 2 IN 32.76816MHz OSC IN X OUT OSC 2 OUT 32.76816MHz OSC OUT P22/OSC IN3 OSC 3 IN 14.318 MHz OSC IN P21/OSC OUT3 OSC 3 OUT 14.318 MHz OSC OUT CLKSEL CLK SEL P20/OSC...
Page 77
PIN No. Port Pin Name DESCRIPTION ACTIVE CAM A CAM DATA INPUT CAM B P106 CAM D CAM A CAM B CAM C CAM D C.FG C.FG IN CAPSTAN FG INPUT PULSE AMP VSS AMP VSS D.FG IN DRUM FG INPUT PULSE PDRPGIN D.PG IN...
Page 82
I.C PIN DESCRIPTIONS (VPS/PDC : SDA5650X) : IC11 PIN No PIN Name Function VSSA Analog ground (0V) VSSD Digital ground (0V) No Connected Serial clock input of I2C Bus Serial clock input of I2C Bus Chip select input determing the I2C Bus addresses: 20H / 21H, when pulled low 22H / 23H, when pulled high Video Composite Sync output from sync slicer used for...
Page 84
Sound IC (MSP3407G : IC01, *MSP3417 : NICAM) PIN DESCRIPTIONS NC = not connected; leave vacant LV = if not used, leave vacant DVSS: if not used, connect to DVSS X = obligatory; connect as described in circuit diagram AHVSS: connect to AHVSS Connection Pin No.
Page 85
Connection Pin No. Pin Name Type Short Description (if not used) DACM_R Loudspeaker out, Right DACM_L Loudspeaker out, Left Not connected VREF1 Reference ground 1 high-voltage part SC1_OUT_R SCART 1 output, Right SC1_OUT_L SCART 1 output, Left Not connected AHVSUB Analog power supply 8.0V CAPL_M Volume capacitor MAIN...
TUNER (PAL : PTMI-5MH02A : TU51) Pin Function Pin No. Pin Name Function NC(BB +5V) AUDIO IN Audio Input CH SW REG(+5V) CONTROL VCR/TV VIDEO IN Video Input RF AGC Clock Input Data Input/Output IF OUT IF Output AUDIO OUT Audio Signal Output SIF OUT Sound IF signal Output...
Page 88
Reset IC (KA75330ZT : IC33, KA75390ZT : IC34) PIN DESCRIPTIONS Pin Number Pin Name Pin Function Description Input Ground Output PIN ASSIGNMENTS 1. V 3. RST 2. GND BLOCK DIAGRAM 1:TO-92 1:TO-92 3:SOT-89 3:SOT-89 3:TO-92 3:TO-92 1:SOT-89 1:SOT-89 2:TO-92 2:TO-92 2:SOT-89 2:SOT-89 - 88 -...
Page 89
EEPROM (24WC08P : IC35) PIN DESCRIPTIONS Pin No. Pin Name Function SDA2 Serial Data/Address SCL2 Serial Clock Write Protect +1.8V to +6V Power Supply BLOCK DIAGRAM PIN ASSIGNMENTS V CC EXTERNAL LOAD SENSE AMPS D OUT SHIFT REGISTERS V SS V CC WORD ADDRESS COLUMN...
Page 93
VIN1 VOUT IC10(2.8V RESET IC) PIN NO. DESCRIPTION VOLTAGE IC80(NJM2296) VOUT PIN NO. DESCRIPTION VOLTAGE VOUT1 VIN5 IC34(NJM2580) VIN4 PIN NO. DESCRIPTION VOLTAGE VIN3 VIN1 GND1 VIN2 VIN2 GND2 VOUT VIN3 GND3 VIN1 POWER SAVE VSAG VOUT VOUT3 VOUT2 IC37(74VHC04MX) VOUT1 PIN NO.
Page 94
IC62(NJM2068M) PIN NO. DESCRIPTION VOLTAGE CKS2 A OUTPUT 11.1 CKS0 A -INPUT 11.1 A +INPUT IC29(PCM1754) 11.7 B +INPUT PIN NO. DESCRIPTION VOLTAGE B -INPUT 11.1 B OUTPUT 11.1 DATA LRCK DGND IC27(BA7607F) PIN NO. DESCRIPTION VOLTAGE VOUTL IN2a VOUTR CTL A AGND OUT a...
T-6 (VCR MECHANISM) ASSEMBLING DIAGRAM A. TOP VIEW 1 MAINBASE ASS’Y 9 IDLER PLATE TOTAL ASS’Y 17 AC HEAD ASS’Y 2 DRUM ASS’Y 10 T BRAKE ASS’Y 18 T SLANT POLE ASS’Y 3 FE HEAD 11 FL RACK 24 CABLE FFC 4 S SLANT POLE ASS’Y 12 RELAY LEVER 5 TENSION BAND ASS’Y...
Page 99
B. BOTTOM VIEW 19 LOADING RACK 20 L LOADING ASS’Y 21 R LOADING ASS’Y 22 CONNECT PLATE 23 REEL BELT 24 CABLE FFC - 99 -...
Page 100
T-6 (VCR MECHANISM) EXPLODED VIEW A. TOP VIEW - 100 -...
ADJUSTMENT OF THE TAPE TRANSPORT SECTION. Generally, tape transporting section has been precisely adjusted in the factory and does not require the ordinary readjustment. But there is the case that tape noise or impact on the deck mechanism, tape transporting section readjustment is required. In adjustment of the tape transmission section refer to the following flow chart.
Page 104
A. Adjustment of the S/T GUIDE ROLLER a. Check the Playing back with a T-120 TAPE. b. Make sure that exessive tape wrinkle does not occure ateatch S,T GUIDE ROLLER c. If tape wrinkle is observed at the S/T GUIDE ROLLER, turn the guide roller screw until there is not tape wrinkle.
Page 105
D. Adjustment of the AUDIO AZIMUTH (Fig. 4) a. Play blck the ALIGNMENT TAPE (DN2 : SP, NTSC, 7KHz) b. Check the AUDIO output with a AUDIO LEVEL METER. c. Turn the AC HEAD AZIMUTH SCREW ② until the maximum AUDIO output (-9dBm ~ -3dBm)is obtained FIg.5.4 Adjustment of AUDIO AZIMUTH, X-POSITION E.