Page 1
5512098 Junior Loft With Storage Steps White / Pink DO NOT RETURN PRODUCT TO THE STORE STOP Individual stores do not stock parts. If a part is missing or damaged, call our toll-free customer service line. We will gladly ship your replacement parts FREE of charge.
Warranty Information DHP warrants this product to be free from defects in material and workmanship and agrees to remedy any such defect. This warranty covers one year from the date of original purchase. This is solely limited to the repair or replacement of defective parts and no assembly labor is included.
HARDWARE PACK T5512098-00-1/2 ST4.2 X 10mm 1/4" X 5/8" 1/4" X 3/4" 5/16" X 3/4" X 38 1/4" X 7/8" 1/4" X 1 1/4" X 10 1/4" X 2 3/16" 1/4" X 2 3/4" T5512098-00-2/2 ST4.2 X 12mm X 12 X 28 1/4"...
Page 8
Attach (I) & (T) to (C) & (D) with finger tighten BOLTS (5); Set (M) to (C & D) with screw holes at the same side. 8 / 36...
Page 9
Attach (U) to (A) & (S), then set (L) to (A) & (S); Fix them in place with BOLTS (5) X 5. Attach (H) to (A),(B) & (S) using (P) X 3 with BOLTS (1); Attach (F) to (A) & (B) with BOLTS (5). 9 / 36...
Page 10
Please Note: Wide side of the Attach (G) to (A, B, C & D) with BOLTS (6). slot should be facing up ! Attach (E) & (J) to (A, B, C & D) with BOLTS (5); Then fix (E) to (G) with BOLTS (2). X 11 10 / 36...
Page 11
Slide (O) into the slots on (G), then lock (O) into place with (Y). 11 / 36...
Page 12
Press (W) onto (O), then press (Q) into (W) alternating left and right. 12 / 36...
Page 13
Attach (W1) to (B) & (D1) with BOLTS (5) X 2; Attach (V) to (B & D1) with BOLTS (2). Set (X) into (B & D1); Then fix with BOLTS (5) X 3. 13 / 36...
Page 14
Set (Z) to (K) with SCREW (8); Attach (Z) & (P) to (X) with BOLT (1); Attach (D2) to (D1 & K) with BOLTS (5) then attach (E2) to (D1 & K) with BOLTS (5). 14 / 36...
Page 15
For the following steps you may need a SCREWDRIVER! Screw (11) onto (A1) & (F1); Attach (A1) & (F1) to (I1) then fasten by turning CAM (13) clockwise as far as possible. 15 / 36...
Page 16
Screw (11) onto (B2); Attach the subassembly from previous step to (B2) then fasten by turning CAM (13) clockwise as far as possible. 16 / 36...
Page 17
Attach (N) to (I2) with SREWS (7) then attach (N) to (F1) with SCREWS (7). 10.1 10.2 NOTE: Please ensure a clearance between (I2) and (B2) to avoid scratching between the two parts. X 12 17 / 36...
Page 18
Attach (C1) to (B2) with BOLTS (4); Then place the subassembly to the bed frame as shown. 11.2 11.1 18 / 36...
Page 19
12.1 Disassemble the BOLT (1) for the (S) as shown in the zoom view. 12.2 Attach (R) to (H & F) with BOLT (1); Fasten (B2) to (F & D2) with BOLTS (3); Attach (B1) to (Z) with BOLT (14) then to (D2) with BOLT (1). 12.1 12.2 19 / 36...
Page 20
Attach (C1) to (A2) with BOLTS (4); Attach (K1) to (C1) with BOLTS (3). Place the subassembly into place as shown then fasten it to (B & D1) with BOLTS (2) and to (B1 & R) with BOLTS (3). 13.1 13.2 13.4 13.3...
Page 21
Screw (11) into (F2) & (C2); Insert (12) on both side of (F3). Attach (F3) & (K2) to (F2) & (C2); Fasten by turning CAM (13) clockwise as far as possible. 14.2 14.1 14.3 21 / 36...
Page 22
Screw (11) into (J1); Attach the subassembly from previous step to (J1); Fasten by turing CAM (13) clockwise as far as possible. 15.1 15.2 15.3 22 / 36...
Page 23
Screw (11) into (E1) then stick PAD (9) on (E1) as shown below. Attach (E1) to the subassembly from previous step; Fasten by turning CAMS (13) clockwise as far as possible. 16.1 16.3 16.4 16.2 23 / 36...
Page 24
Attach (X1) to (J1) with BOLTS (4); Turn the drawer over then place it to place as shown below. Once assembly is complete, please make sure all hardware is tightened. 17.1 17.2 24 / 36...
Page 25
T919380 T921500 T921490 NOTE: (Y1), (V1) & (Z1) have been pre-assembled on (A/B/C/D/D1/K), (E2) & (X1). They are available for replacement. 25 / 36...
Page 26
PERIODICALLY CHECK AND ENSURE THAT THE GUARDRAIL, LADDER AND OTHER COMPONENTS ARE IN THEIR PROPER POSITION, FREE FROM DAMAGE, AND THAT ALL CONNECTORS ARE TIGHT. REPLACEMENT PARTS, INCLUDING ADDITIONAL GUARDRAILS, MAY BE OBTAINED FROM ANY OF OUR (DHP) DEALERS. DO NOT ALLOW HORSEPLAY ON OR UNDER THE BED AND PROHIBIT JUMPING ON THE BED.
Page 28
Una la parte (I) & (T) en (D) & (C) apretando con los dedos los TORNILLOS (5); Coloque parte (M) en (C) y (D). Una la parte (U) en (A) & (S), y luego (L) en (A) & (S); Coloque en su lugar utilizando TORNILLOS (5)x 5. Una la parte (H) en (A, B & S) utilizando (P) x 3 con TORNILLOS (1);...
Page 29
TORNILLOS (2) y en (B1 & R) con TORNILLOS (3). Atornille (11) en (F2) & (C2); Introduzca las piezas (12) en ambos lados de (F3). Una (F3) & (K2) a la parte (F2) & (C2); Apriete girando los CAM(13) hacia la derecha lo Atornille (11) en (E1) y despues pegue la ESPONJA (9) en (E1) como se muestra abajo.
Page 30
CAMA SE DEBE COLOCAR CONTRA LA PARED PARA PREVENIR QUEDAR ATRAPADO ENTRE LA CAMA Y LA PARED. A, GANCHOS, CORREAS Y CUERDAS DE SALTAR.