Page 2
General notes With respect to any damages arising in operation with the described product or this document, S&T shall be liable according to the General Conditions on which the delivery of the described product and this document are based. This product is not intended for use in life support appliances, devices or systems where a malfunction of the product can reasonably be expected to result in personal injury.
Sales/technical force management Scope The purpose of this document is to describe how to getting started with the IntelliTrac P1 Personal Tracker devices. The document contains basic device configuration. For advanced users, please refer to the IntelliTrac P1 personal tracker Protocol Document for detailed information.
FCC Regulations: This mobile device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This mobile device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
IntelliTrac P1 Personal Tracker User Guide Hardware Installation (1) SIM Card Installation Unscrew the battery access to open the battery cover (a), Pull out the battery(b), Insert the SIM Card. Insert the Battery pack into battery bay.
Page 7
IntelliTrac P1 Personal Tracker User Guide image1 (2) Charging IntelliTrac P1 To Start Charge IntelliTrac P1 by, Power recharge by connecting the USB Sync cable to PC’s USB connector. Power recharge by connecting the AC Power adaptor Power LED status during charging: Charging –...
Page 9
Computer” as shown below, or from “Control Panel System Hardware Device Manager” Once power on IntelliTrac P1, and connect P1 to PC via USB cable; there will be a pop-up windows appearing as Please simply click which window, “Found new Hardware”, to start Hardware Wizard; and ...
Page 10
IntelliTrac P1 Personal Tracker User Guide Please find a correct location to load drivers for installation. Once you find a correct drivers, Windows system will start to load related data to OS. and present a “Completing The Found New Hardware Wizard” windows.
IntelliTrac P1 Personal Tracker User Guide Device Configurations For the first installation, some basic parameters should be set before installation. The device parameters can be set through RS-232 port by using HyperTerminal program. Please see below for the HyperTerminal settings: (1) Open HyperTerminal Systems &...
Page 15
IntelliTrac P1 Personal Tracker User Guide (5) Type AT$VERSION command and press [Enter] key, the hardware and firmware version will be shown on the HyperTerminal. If the HyperTerminal is shown like below, that means connection between the device and PC is working properly. It is ready to send all configuration commands from now on.
IntelliTrac P1 Personal Tracker User Guide Communication Settings There are two communication modes for the IntelliTrac P1 Personal Tracker device to communicate to the control center. One is SMS, and the other is GPRS (TCP/UDP). The device should be set communication parameters before install the device to vehicle.
Page 17
IntelliTrac P1 Personal Tracker User Guide (2) GPRS Configuration Setting GPRS server using the following commands: AT$APN=internet,username,password (APN=internet, Username=username, Password=password) AT$HOSTS=1,60.148.19.10,6000 (Server IP address = 60.148.19.10 and Port number =6000) AT$RETRY=5,10 (Message retry settings) AT$IPTYPE=1 (Using TCP/IP mode) AT$GPRSEN=1 (GPRS enable) Please refer to IntelliTrac A Series Protocol Document for detailed command descriptions.
IntelliTrac P1 Personal Tracker User Guide GPS Tracking Configurations After the device communication settings are done. The remote GPS tracking function can be performed. The GPS tracking function can be set by using AT$PDSR command. For example, AT$PDSR=1,30,0,0,2,0,0,1,1 (Tracking through GPRS by time interval 30 seconds) For the simply testing GPRS, open the TCP Server A-Series software which is provided by S&T.
Page 19
IntelliTrac P1 Personal Tracker User Guide For advanced testing, please use the IntelliTrac Tracer Plus software; you can download free trial version from S&T’s FTP server site as: ftp://ftp.systech.com.tw/AVL/AVLS_TracerPlus/ Username : st1234 Password : st1234 You also can apply a testing account from S&T’s Fleetweb solution from your contact sales.
IntelliTrac P1 Personal Tracker User Guide Firmware Upgrade The IntelliTrac P1 firmware is updated through the serial interface. The firmware update of the device can be performed with the IntelliTrac A series firmware loader tool provided by S&T. It runs on Windows based PCs.
IntelliTrac P1 Personal Tracker User Guide CHARACTERISTICS Dimensions ( L x W x H) 110.0 x 95.0 x 30.0mm Weight 110gm Radio Performance Frequency (MHz) Quad-Band 850/900/1800/1900MHz Transmit Power 1W/1800MHz,1900Mhz 2W/850MHz, 900MHz GSM Functionality / GPRS GPRS Mode MultiSlot Class 10 , Mobile Station Class B...
IntelliTrac P1 Personal Tracker User Guide & & IntelliTrac P1 Personal Tracer is produced by Systems & Technology Corporation. The company is a key developer and supplier of advanced systems in the Automatic Vehicle Location (AVL), Digital Map and Car Navigation Systems.