Page 2
General notes With respect to any damages arising in operation with the described product or this document, S&T shall be liable according to the General Conditions on which the delivery of the described product and this document are based. This product is not intended for use in life support appliances, devices or systems where a malfunction of the product can reasonably be expected to result in personal injury.
IntelliTrac A1-lite Series User Guide Thank you for your purchasing IntelliTrac A1-lite GPS Vehicle Tracking device. The benefits are: Improve Safety Ensure Security Good efficiency on Fleet management and Dispatch solution Asset and resource management Economic operation and improving productivity...
IntelliTrac A1-lite Series User Guide About IntelliTrac A1-lite The IntelliTrac A1-lite GPS Unit wirelessly transmits location, peripheral, and vehicle control data to a control center. Location data, including speed, direction, mileage, and altitude, is provided by an onboard GPS receiver. Wireless transmission is achieved using an onboard GSM/GPRS module. A microcontroller is used to poll location and command data at regular intervals, derive actions based on location, peripheral, and control data, and execute those actions.
IntelliTrac A1-lite Series User Guide Hardware Architecture The IntelliTrac A1-lite hardware includes Micro-controller, GPS receiver, GSM/GPRS modem, G-Force sensor, I/Os interfac. User can use PC HyperTerminal connect to the Diagnostic / setting port to configure the AVL. The G-Sensor is used for car accident. Car tow-away warning and power management.
IntelliTrac A1-lite Series User Guide Related Documents [1] IntelliTrac A Series Protocol Document Basic Operations Hardware Installation (1) SIM Card Installation Press yellow button to eject the SIM card holder. Put the SIM card on the SIM card holder. Insert the SIM card holder to the device correctly.
Page 8
IntelliTrac A1-lite Series User Guide (2) GPS Antenna Installation Connect the GPS antenna to the right-down corner SMA connector. Recommended mating torque for the SMA connector is 7-10 inch pounds (80-110 N.cm). (3) Power,RS-232 and I/O Cable Installation Connect 4-wires power cable to the device, The D-SUB can be connected to the COM port of PC.
IntelliTrac A1-lite Series User Guide Connectors Pins Assignment PWR / IO Connector Pin# Signal Name Description Electrical Characteristic DC IN = DC8 to 30V, Inormal = 70mA @12V - Black Ignition Brown min = 30V, V max = 6.8V(High Active)
IntelliTrac A1-lite Series User Guide Device Configurations For the first installation, some basic parameters should be set before installation. The device parameters can be set through RS-232 port by using HyperTerminal program. Please see below for the HyperTerminal settings: (1) Open HyperTerminal...
Page 13
IntelliTrac A1-lite Series User Guide (5) Type ATI command and press [Enter] key, the hardware and firmware version will be shown on the HyperTerminal. If the HyperTerminal is shown like below, that means connection between the device and PC is working properly. It is ready to send all configuration commands from now on.
IntelliTrac A1-lite Series User Guide Communication Settings There are two communication modes for the IntelliTrac A series device to communicate to the control center. One is SMS, and the other is GPRS (TCP/UDP). The device should be set communication parameters before install the device to vehicle.
Page 15
IntelliTrac A1-lite Series User Guide (2) GPRS Configuration Setting GPRS server using the following commands: AT$APN=internet,username,password (APN=internet, Username=username, Password=password) AT$HOSTS=1,60.148.19.10 (Server IP address = 60.148.19.10) AT$RETRY=5,10 (Message retry settings) AT$IPTYPE=1 (Using TCP/IP mode) AT$PORT=6000 (Host application port) AT$GPRSEN=1 (GPRS enable)
IntelliTrac A1-lite Series User Guide GPS Tracking Configurations After the device communication settings are done. The remote GPS tracking function can be performed. The GPS tracking function can be set by using AT$PDSR command. For example, AT$PDSR=1,30,0,2,0,0,1,1 (Tracking through GPRS by time interval 30 seconds) For the simply testing GPRS, open the TCP Server A-Series software which is provided by S&T.
IntelliTrac A1-lite Series User Guide Firmware Upgrade The IntelliTrac A Series device firmware is updated through the serial interface. The firmware update of the device can be performed with the IntelliTrac A series firmware loader tool provided by S&T. It runs on Windows based PCs.
IntelliTrac A1-lite Series User Guide CHARACTERISTICS Dimensions ( L x W x H) 135 x 70 x 35mm (With Connector) Weight 170gm Radio Performance Frequency (MHz) Quad-Band 850/900/1800/1900MHz Transmit Power 1W/1800MHz,1900Mhz 2W/850MHz, 900MHz GSM Functionality / GPRS GPRS Mode MultiSlot Class 10/B , Mobile Station Class B...
IntelliTrac A1-lite Series User Guide & & IntelliTrac A-Series AVL device is produced by Systems & Technology Corporation. The company is a key developer and supplier of advanced systems in the Automatic Vehicle Location (AVL), Digital Map and Car Navigation Systems.