Table of Contents General Introduction ........................1 Overview ........................1 Features ......................... 1 Framework and Dimensions ..................... 2 Installation............................ 5 Menu ............................. 8 HDCVI Series DVR Settings ..................8 Menu Operation ......................8 Appendix Ⅰ Maintenance ......................... 11 Appendix Ⅱ Toxic or Hazardous Materials or Elements ............12...
Page 3
Welcome Thank you for purchasing our HDCVI camera! This user’s manual is designed to be a reference tool for your system. Please read the following safeguard and warnings carefully before you use this series product! Please keep this user’s manual well for future reference!
Important Safeguards and Warnings 1.Electrical safety All installation and operation here should conform to your local electrical safety codes. We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation. 2.Transportation security Heavy stress, violent vibration or water splash are not allowed during transportation, storage and installation.
Page 5
Applicable Models This manual can be applied to the models of HAC-HFWXXXXB, HAC-HFWXXXXD and HAC- HFWXXXXE. Note: “XXXX” are the 4 numbers in the model, such as 2120.
1 General Introduction 1.1 Overview This series HDCVI camera conforms to the HDCVI standard. It supports video signal high-speed long distance transmission without any delay. It can be controlled by the DVR conforming to the HDCVI. 1.2 Features High-performance CMOS image sensor, megapixel definition. ...
2 Framework and Dimensions Please refer to the following figure for dimension information of HAC-HFWXXXXB. The unit is mm. See Figure 2-1. Figure 2-1 Please refer to the following figure for dimension information of HAC-HFWXXXXD. The unit is mm. See Figure 2-2. Figure 2-2 Please refer to the following for dimension information of HAC-HFWXXXXE.
Page 8
Figure 2-3 Please refer to the following figure for structure information. See Figure 2-4. Figure 2-4 Please refer to the following sheet for detailed information. Name Function Lens It is to receive the optical signal from the environments. Sunshield Cover Bracket Support camera body and rotate to adjust monitor angle.
Page 9
Note: When SD/HD switch control cable is in short circuit, it can realize the switch from HD video output to SD video output. On the contrary, the control cable will be switched back to HD video output in the open circuit. ...
3 Installation Important Please make sure the installation surface can min support the 3X weight of the camera and the bracket. Step 1 Install camera bracket Please install the expansion bolt if you want to install in the cement wall (Please make sure the installation holes of the expansion bolts are the same with the bracket.) Then you can install the bracket.
Page 11
Please refer to the steps listed below for installation information of HAC-HFWXXXXE. Figure 3-2 Step 1 Install the camera bracket according to your installation mode. Before you install the bracket, please pull the cable through the cable exit of the installation surface or pull the cable through the cable exit of the bracket.
Page 12
Step 4 Use the L wrench (provided) to loosen the adjusting screw to make the camera can monitor the corresponding surveillance zone. Use the L wrench to adjust the adjusting screw to fix the camera firmly. Please refer to (B) and (C) in Figure 3-2. Step 5 Connect the video output port of the device cable to the rear-end encode device such as DVR or NVS.
4 Menu 4.1 HDCVI Series DVR Settings This HDCVI camera series can adjust OSD menu via coaxial control. After connected the camera to the HDCVI series DVR, from Main Menu->Setting->System->PTZ, you need to select the channel number for access and set control mode as HDCVI and the protocol as DH-SD1. Click “Save”...
Page 14
Figure 4-3 See Sheet 4-1 for the details of button functions. Button Function Open menu or confirm Open menu Select menu item 、 Select menu value 、 Sheet 4-1 The main menu interface is shown in Figure 4-4.
Page 15
Figure 4-4 If there is “ ”, click iris “+” or the “Confirm” button in “Menu Operation” interface to go to the 2nd menu. Click “Return” button to go back to the previous menu interface. Note: The operation interface above is the example of HCVRHG-AF series, different rear-end devices have different operation interfaces;...
Appendix Ⅰ Maintenance Attention: Please maintain the device according to the following instructions in order to ensure the image effect and long-term stable operation of the device. Maintenance for lens and mirror surface The lens and mirror surface are covered with antireflection coating, so it may produce hazardous substance and lead to performance reduction or scratch, dimness etc when it is stained with dust, grease, fingerprint and so on, please refer to the following methods to deal with once dirt is found: Stained with dirt...
Appendix Ⅱ Toxic or Hazardous Materials or Elements Toxic or Hazardous Materials or Elements Component Name Cr VI PBDE Circuit Board ○ ○ ○ ○ ○ ○ Component Device ○ ○ ○ ○ ○ ○ Construction Material Wire and ○ ○...