Advertisement
Quick Links
Advertisement
Related Manuals for Aeon Labs Aeotec MULTISENSOR 6
Summary of Contents for Aeon Labs Aeotec MULTISENSOR 6
- Page 1 MULTISENSOR 6 View the expanded manual: http://aeotec.com/support...
- Page 3 Ultraviolet sensor. Vibration sensor. The corner of your room just got smarter. Aeotec by Aeon Labs’ MultiSensor looks like a motion sensor and it acts like one too. But it’s also so much more. Installing this 1 piece of Z-Wave® technology is the same as installing 6 pieces of Z-Wave technology.
- Page 4 Certifications (regional): Z-Wave and Z-Wave Plus are registered trademarks of Sigma Designs and its subsidiaries in the United States and other countries FCC ID: XBAFT100 Version: 501010000001-AB www.aeotec.com Screw hole Action Button Light Sensor Motion Sensor and UV Sensor RGB LED Battery cover Unlock Lock...
- Page 5 generates, uses and can radiate radio frequency energy and, if Quick start. not installed and used in accordance with the instructions, may Setup your power. cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular Your MultiSensor can be powered by battery or by USB with installation.
- Page 6 DEEMED WAIVED UNLESS MADE IN WRITING WITHIN THIRTY (30) DAYS 2. Insert CR123A batteries oriented according to the picture below. FROM AEON LABS'S DELIVERY, OR THE DATE FIXED FOR DELIVERY IN Your MultiSensor is now powered on. THE EVENT OF NONDELIVERY.
- Page 7 Aeon Labs' manufacturing processes. IN NO EVENT SHALL AEON LABS BE LIABLE FOR ANY INDIRECT, INCIDENTAL, PUNITIVE, SPECIAL OR CONSEQUENTIAL DAMAGES, OR DAMAGES FOR LOSS OF PROFITS, REVENUE, OR USE INCURRED...
- Page 8 Aeon Labs does not authorize any person or party to assume or Light can impact on the quality of motion readings, it’s also...
-
Page 9: Warranty
Customer. Warranty claims must be made by Customer in writing within thirty (30) days of the manifestation of a problem. Aeon Labs' sole obligation under the foregoing warranty is, at Aeon Labs' option,... - Page 10 For optimal performance, your MultiSensor should NOT be The MultiSensor contains a smart Vibration sensor in. When mounted directly on or near metal framing or other large metallic someone attempts to disassemble your MultiSensor, it can detect objects. Large metal objects may weaken the Z-Wave wireless the vibration and send an alarm notification to the main controller signal.
- Page 11 Parameter 111-113 [4 byte decimal] can be configured through your gateway in case the default settings of your MultiSensor are not what you desire. Parameter 111 will set the interval for Group 1 (parameter 101), parameter 112 will set the interval for Group 2 (parameter 102), and USB port parameter 113 will set the interval for Group 3 (parameter 103).
- Page 12 Setting automatic report flags. Parameter 101-103 [4 byte dec] can be configured through your gateway in case the default settings of your MultiSensor are not Lock what you desire. Decimal Flag Light Sensor Humidity Sensor Temperature Sensor Unlock Ultraviolet Sensor Screw hole Battery Sensor The Back-Mount Arm may be locked at various angles by turning...
- Page 13 The specific Z-Wave commands Aeotec by Aeon Labs’ Z-Stick and Minimote controllers. If you are for the support of monitoring is the Multilevel Sensor Command using other products as your main Z-Wave controller, please refer Class.
- Page 14 If you’re using a Z-Stick: Take your Minimote to your MultiSensor. Press the Remove Button on your Minimote. Press the Action Button on your MultiSensor. If your MultiSensor has been successfully removed from your network, the RGB LED will be active with a colourful gradient for 3 seconds.
Need help?
Do you have a question about the Aeotec MULTISENSOR 6 and is the answer not in the manual?
Questions and answers