Table of Contents
Advertisement
Programming your Remote Control
Introduction
Your remote lets you control four devices with one easy-to-use, compact unit. After installing batteries, you can program the remote to
control your Universal TV, VCR or DVD, Cable or Satellite Receivers, Amplifier or Tuner, and Auxiliary devices. To do so, follow the
instructions in "Programming a Device". For best results, please read and follow all the remaining instructions. Keep this guide for future
reference.
A Quick Look at Programming a Device
To control VCR or DVD, Cable or Satellite Receivers, Amplifier or Tuner, and Auxiliary devices, follow these steps. Before proceeding, find
the codes for the devices you want to program in "Manufacturer's Codes" in pages 35-47 and write them down or highlight them.
NOTE:
To program a DVD Player, TV/DVD Combo, TV/VCR/DVD Combo, portable DVD player, or mobile DVD player, use the
1.
Turn on the device (for example, DVD player) and, if needed, load media (for example, a DVD).
2.
Press a device key (
VCR/DVD, CBL/ SAT,
3.
Press and hold
SET
until the red LED blinks twice; then release.
4.
Enter the first five-digit code for your device. The LED blinks once as each digit is entered. If the code is correct, the LED blinks
twice.
?
NOTE:
If the LED does not blink twice, repeat steps 2 to 4 and try entering the code again.
5.
Aim the remote at the device and press
your brand until you find one that works. If you cannot find a code that works, see "Searching for Your Code".
6.
Repeat steps 15 for the other devices you want to control. For future reference, write down each working device code below:
AUX
Code:
CBL
Code:
CD
Code:
DVD
Code:
SAT
Code:
TNR
Code:
VCR
Code:
7.
Press set to save and exit
Searching for your Code
If your device does not respond to the remote after trying all codes listed for your brand, or if your brand is not listed, try searching for your
code:
1.
Press a device key once.
2.
Press and hold
SET
until the red LED blinks twice; then release.
3.
Enter
9-9-1
, then the device group number (0= Cable, 1= TV, 2= VCR, 3= Audio). The LED blinks twice.
4.
Aim the remote at the device and press
the most popular code first. If the device responds, go to step 7.
5.
If the device does not respond, press
?
NOTE:
Press
CH-
to try the previous code.
6.
To search for other device codes, repeat steps 1 to 5.
7.
Press
SET
to save and exit.
Checking the Codes
If you have set up the remote using the procedure in "Searching for Your Code", you may need to find out which four-digit code is operating
your equipment.
For example, to find out which code is assigned to your TV:
1.
Press
TV
once.
2.
Press and hold
SET
until the red LED blinks twice; then release.
3.
Enter
9-9-0
. The LED blinks twice.
4.
To view the code for the first digit, press . Count the LED blinks (for example, three blinks = 3), and write down the number in the
appropriate code listing in step 8 under "Programming a Device".
?
NOTE:
If a code digit is , the LED does not blink.
5.
Repeat step 4 for the four remaining digits, using
digit.
6.
To check for other device codes, repeat steps 15, substituting the device key for
or
AUX
).
Power
. The device should turn off. If it does not, repeat steps 35, trying each code for
Power
. The remote sends IR codes from its library to the selected device, starting with
CH+
. The remote will try the next code. Continue until the device responds.
1
0
2
for the second digit,
3
for the third digit,
TV
.
32
DVD
4
for the fourth digit, and
5
for the fifth
key.
Advertisement
Table of Contents
