Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Repair Manual
TRIUMPH 440
SELF-CONTAINED CARPET EXTRACTOR
INTRODUCTION
This operator's book has important information for the use
and safe operation of this machine. Read this book care-
fully before starting the machine. Keep this book and tell
all operators to read the book. If you do not follow the
instructions, you can cause an injury or damage equipment,
furniture or buildings.
For new books write to:
Pacific Steamex, Inc.
2259 S. Sheridan
Muskegon, MI 49442-6252
Carefully inspect all components to ensure that there is no
concealed freight damage. If such damage is discovered,
file a "CONCEALED DAMAGE REPORT" immediately
with the delivering carrier.
DYNAMO
&
READ THIS BOOK
OPERATING & MAINTENANCE
INSTRUCTIONS
The contents of this manual are based on the latest product
information available at the time of publication. Pacific
Steamex reserves the right to make changes or improve-
ments to its machines without notice.
FOR YOUR CONVENIENCE, RECORD THE
FOLLOWING IMPORTANT INFORMATION:
MODEL_______________________________
SERIAL NUMBER_______________________
PART NUMBER ________________________
DATE PURCHASED _____________________
Advertisement
Table of Contents
Related Manuals for Pacific Steamex DYNAMO
Summary of Contents for Pacific Steamex DYNAMO
- Page 1 FOR YOUR CONVENIENCE, RECORD THE For new books write to: FOLLOWING IMPORTANT INFORMATION: Pacific Steamex, Inc. 2259 S. Sheridan MODEL_______________________________ Muskegon, MI 49442-6252 SERIAL NUMBER_______________________ Carefully inspect all components to ensure that there is no concealed freight damage.
-
Page 2: Grounding Instructions
INTRODUCTION This carpet extractor is a fully self-contained, portable system. This machine has a 60 psi solution pump and a one (1) jet spraying system to apply solution to the carpet. A 10 inch rotating brush is driven by a cogged belt system at approximately 1000 RPM’s. This brush provides a very aggressive agitation of the solution into the carpet fibers to loosen ground-in dirt. -
Page 3: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE WARNING : To reduce the risk of fire, electric shock, or injury: 1. You must have training in the operation of this machine before using it. 2. -
Page 4: Operating Procedures
OPERATING PROCEDURES WARNING! For the safe operation of this machine OPERATION follow the instructions given in this booklet and the train- The following procedures are intended to describe and de- ing given by your supervisor. Failure to do so can result tail proper operation of your machine. -
Page 5: After Each Use
9. Tilt the machine back on the rear wheels and walk After Each Use: forward to position the machine along side the previ- Clean the dome top, gasket and recovery tank with ous pass (slightly overlapping). fresh,clean water. Do not reinstall the dome until the next use, this will allow the recovery tank to dry out. - Page 6 Machine Vacuum Motor 73-75 Mounting Sets (3): PUMP: Access from bottom of machine by removing brush housing, then remove 4 plate screws located under recovery tank. 63, 64 Inline Strainer Assembly 03/01...
-
Page 7: Machine Parts List
Machine Parts List ITEM PART NO. DESCRIPTION QTY. ITEM PART NO. DESCRIPTION QTY. 962007 Screw 980002 Washer, 1/4 Lock 980004 Washer, 1/4 Flat 962151 Screw, 1/4-20 x 4 HHCS SS 248201 Spacer, Tank Handle W189D Screw, 1/4-20 x 3/4 HH SS 243902 Handle, Recovery Tank 243403... - Page 8 Brush Housing Assembly 03/01...
- Page 9 Brush Housing Assembly Parts List ITEM PART NUMBER DESCRIPTION QTY. 903009 Belt 246901 Pulley, Drive 240804 Bracket, Motor Mting 245202 Motor, Brush Drive W329D Nut, 10-32 Hex 980015 Washer, #10 Ext. Tooth 920017 Nut, 10-24 ESNA S/S 240812 Bracket, Top Single Jet S296P Brass Barb 1/4 to 1/8 MPT 243306...
- Page 11 WIRING DIAGRAM WIRING DIAGRAM MACHINE WITH OPTIONAL HOUR METER...
-
Page 12: Warranty Policy
The inoperative machine or warranted parts must be delivered to the authorized dealer with shipping and delivery charges prepaid. If unable to locate the Dealer, you may contact Pacific Steamex Inc. at the address listed herein for the location of the nearest Pacific Steamex Inc. repair center or agent or for other instructions pertaining to your warranty difficulty.