Table of Contents
Related Manuals for Neilsen CT0878
Summary of Contents for Neilsen CT0878
- Page 1 AIR IMPACT WRENCH - 1" DR CT0878 ORIGINAL INSTRUCTIONS Cannon Tools Limited Address: 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K. SAVE THESE INSTRUCTIONS AND PRECAUTIONS. READ ALL PRECAUTONS AND INSTRUCTIONS BEFORE USE.
-
Page 2: Ec Declaration Of Conformity
In case of alteration of the machine, not agreed upon by us, this declaration will lose its validity. Product description: AIR IMPACT WRENCH - 1” DR Model: CT0878 Applicable EC Directives: EC Machinery Directive 2006/42/EC Harmonized standards EN ISO 12100, EN ISO 11148-6 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K. -
Page 3: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS SYMBOLS In this manual and/or on the machine the following symbols are used: Denotes risk of personal injury, loss of life or damage to the tool in case of non-observance of the instructions in this manual. Wear hearing protection. Wear safety goggles. -
Page 4: Air Source
3. Avoid unintentional starting. Be sure the switch is off before connecting to the air supply. Do not carry the tool with your finger on the switch or connect the tool to the air supply with the switch on. 4. Remove adjusting keys and wrenches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool increases the risk of personal injury. -
Page 5: Specific Safety Instructions
to play tools capacity, higher pressure will rapidly reduce tools life. Always verify prior to using the tool that the air source has been adjusted to the rated air pressure or within the rated air-pressure range. 2. Never use oxygen, carbon dioxide, combustible gases or any bottled gas as an air source for the tool. -
Page 6: Specifications
stop immediately. SPECIFICATIONS Square drive: 1” Free speed: 3900rpm Max. torque:2400N.m Bolt capacity: 38mm Air inlet: 1/2” Min. hose size: 13mm Air pressure: 8-10 kg/cm COMPONENTS AND CONTROLS INITIAL TOOL SET UP/ASSEMBLY Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. -
Page 7: Tool Set Up
more efficient, but are not required. WARNING! TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Do not install a female quick coupler on the tool. Such a coupler contains an air valve that will allow the air tool to retain pressure and operate accidentally after the air supply is disconnected. -
Page 8: Workpiece And Work Area Set Up
inspection, maintenance, or cleaning procedures. TO PREVENT SERIOUS INJURY: Do not adjust or tamper with any control or component in a way not specifically explained within this manual. Improper adjustment can result in tool failure or other serious hazards. Connect an appropriate, impact rated 1” square drive socket onto the anvil. CAUTION! Only use impact rated accessories with this tool. -
Page 9: User Maintenance Instructions
USER-MAINTENANCE INSTRUCTIONS procedures not specifically explained in this manual must be performed only by a qualified technician. WARNING! TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn off the tool, detach the air supply, safely discharge any residual air pressure in the tool, and release the throttle and/or turn the switch to its off position before performing any inspection, maintenance, or cleaning procedures. -
Page 10: Troubleshooting
TROUBLESHOOTING Problem Possible Causes Likely Solutions 1. Check for loose connections and make sure that air supply is providing enough air flow 1. Not enough air (CFM) at required pressure (PSI) to the tool's pressure and/ or air air inlet. flow. -
Page 11: Assembly Diagram And Parts List
ASSEMBLY DIAGRAM AND PARTS LIST... - Page 12 CANNON TOOLS LTD Add: 20 station road, Rowley Regis, west midlands,B65 0JU.U.K. Made in China...