Page 1
Operation anual Digital mplifier M -110N...
Page 2
Welcome personal welcome to you from the management and employees of Inter-M ll of the co-workers here at Inter-M are dedicated to providing excellent products with inherently good value, and we are delighted you have purchased one of our products.
DIGIT L MPLIFIER Unpacking Unpacking lthough your M -110N is neither complicated nor difficult to operate, we recommend you take a few minutes to read this brief manual and familiarize yourself with the important information regarding product features, setup and operation. s with most electronic devices, we strongly recommend you retain the original packaging.
DIGIT L MPLIFIER Features Features Features - COMP CT DESIGN Easy to install and operate with compact design of 1U size and functions. - DIGIT L MPLIFIER CIRCUIT Take up the Digital mplifier Circuit with High efficiency of the rated power 100W, High reliability, Low weight and Low temperature.
DIGIT L MPLIFIER Front Panel Front Panel 1. MIC INPUT J CK FOR INPUT 1 (6.3ø Phone Jack, Balanced) This is a 6.3ø jack on the front channel that is very useful for connecting dynamic microphone. When microphone plugged to the jack, it overrides all the input signals. 2.
DIGIT L MPLIFIER Rear Panel Rear Panel 1.. INPUT 1 TERMIN L This terminal is for microphone. When connecting to balanced signal, be sure to use balanced cable and please refer to the following picture when using unbalanced cable. INPUT 1 (BAL) PHANTOM (Balanced Cable)
Page 8
DIGIT L MPLIFIER 2. SELECT SWITCH OF INPUT 1 PH NTOM MIC This is the switch to select types of microphones. Be able to use either DYN MIC MIC or CONDENSER MIC, and the phantom power of +15V is supplied when using the condenser microphone. MIC: For general dynamic microphones PH NTOM MIC: For condenser microphones 3.
Page 9
DIGIT L MPLIFIER ‘Y’ cable is needed when connecting to computers. (Unbalanced Cable) Use stereo audio pin Y. 3.5ø - EURO Terminal INPUT 3 (UNBAL) (Unbalanced Cable) Use 3.3mm 3P Euro Terminal cable. 7. TEL IN TERMIN L This is the audio input terminal of PBX that can be controlled with master volume control. 8.
DIGIT L MPLIFIER ※ Connecting Speakers Before connecting speakers to M -110N unit, be sure to disconnect the C power cable. - FOR 70V TERMIN L - FOR 25V TERMIN L 6.9Ω 49Ω 6.9Ω 49Ω 49Ω 6.9Ω ※ Make sure that 4 ※...
Page 11
DIGIT L MPLIFIER 10. EXTERN L MUTE CONTROL TERMIN L Connect +, - terminals externally to mute the output signal. 11. C POWER CORD This is the C cord for connecting power. Do not bend, pull, twist, heat and cut by force. It may cause electric shock.
DIGIT L MPLIFIER pplications pplications USING LOW IMPED NCE SPE KER CD PLAYER INPUT 3 INPUT 2 INPUT 1 SPEAKER MODEL NO. MA-110N MIC / AUX DIGITAL AMPLIFIER MUTE (UNBAL) (BAL) (BAL) 4Ω 6.9Ω 49Ω MSIP-REM-IMK-MA-110 PHANTOM TEL IN PRIORITY...
Page 13
DIGIT L MPLIFIER USING HIGH IMPED NCE SPE KER CD PLAYER INPUT 3 INPUT 2 INPUT 1 SPEAKER MODEL NO. MA-110N MIC / AUX DIGITAL AMPLIFIER MUTE (UNBAL) (BAL) (BAL) 4Ω 6.9Ω 49Ω MSIP-REM-IMK-MA-110 PHANTOM TEL IN PRIORITY 110N MUTE...
To obtain specific warranty information and available service locations contact Inter-M directly or the authorized Inter-M Distributor for your specific country or region.
Page 20
Inter-M, Ltd. (Korea) began operations in 1983. Since then, Inter-M has grown to become one of the largest manufacturers of professional audio and commercial sound electronics equipment in the world. Inter-M has gained worldwide recognition for its own branded products, as well as private label manufacturing of electronics sold under other names (OEM).
Need help?
Do you have a question about the MA-110N and is the answer not in the manual?
Questions and answers