Do you have a question about the WMTS-15R and is the answer not in the manual?
Questions and answers
Summary of Contents for Primal Vantage WMTS-15R
Page 1
MODEL: WMTS-15R Tools Required Adjustable Wrench 15’ TRIPOD • Weight Limit 300 lbs. • Do Not Over Tighten Fasteners Instruction and Safety Manual Warning Every year serious injury and even death occurs from hunting related falls. To ensure your safety, please COMPLETELY read and follow this safety manual and ALL warning labels BEFORE assembling, installing or utilizing this product.
TRIPOD SAFETY WARNINGS Please read the following instruction manual and warnings labels completely before utilizing this product. Failure to understand and execute the instructions and warnings may result in serious injury or death. In the event of an accident, have a plan for rescue, including the use of devices that may be easily reached while suspended.
Page 3
TRIPOD SAFETY WARNINGS NEVER use this tripod for any use other than hunting. NEVER use this tripod for trimming trees. NEVER fall asleep in your stand as you may fall out resulting in serious injury or death. ALWAYS be sure to retighten all bolts BEFORE each new use of tripod. ALWAYS have a minimum of three people present when installing or removing this tripod.
Page 4
• We recommend replacing all hardware/cables/nuts/bolts/clips on your tree stand every two (2) years or sooner if inspection finds it necessary. Use only Primal Vantage approved replacement straps and parts. Use of any other straps or parts, will be viewed as a modification to the product. Any modification will void the warranties and relieve Primal Vantage from all liabilities.
MODEL: WMTS-15R ASSEMBLY INSTRUCTIONS PAGE 1 15FT. TRIPOD ALL PHOTOS TAKEN FROM FRONT VIEW UNLESS OTHERWISE NOTED 2. Attach Seat Back to Seat Platform using 1-M12x55mm Bolt on each side. Attach Armrest to Seat Back and Seat Platform using . Use 1-M12x40mm 1.
MODEL: WMTS-15R ASSEMBLY INSTRUCTIONS PAGE 2 15FT. TRIPOD BOTTOM VIEW BOTTOM VIEW 6. With the platform still upside down, Attach Rear Leg Brace to the rear of the platform using 5. Turn the assembled platform over so that the top of 2-M12x75mm Bolts for each Rear Leg Brace.
MODEL: WMTS-15R ASSEMBLY INSTRUCTIONS PAGE 3 15FT. TRIPOD FRONT VIEW CLOSEUP REAR VIEW CLOSEUP 9. Attach Shooting Rail Support the assembled platform using 1-M12x55mm Bolt for each piece. (See Close-Up Photo for correct placement). to the assembled platform and to the INSIDE of the Shooting Rail Supports using 1-M12x40mm Bolt for Attach Support Brace each connection point.
MODEL: WMTS-15R ASSEMBLY INSTRUCTIONS PAGE 4 15FT. TRIPOD 11. Attach each Shooting Rail Cover to Shooting Rail Attach Each Armrest Cover to each Armrest 12. Tie Skirt around the top of Shooting Rail and the Platform. Attach Seat Back Cushion...
MODEL: WMTS-15R ASSEMBLY INSTRUCTIONS PAGE 5 15FT. TRIPOD BOTTOM VIEW . (The Lower Leg has 1 hole on 14. Insert Lower Leg into Upper Leg the Bottom). The brackets on the legs MUST be facing towards the inside of the stand. Secure with 2-M12x55mm Bolts on each leg.
Page 11
MODEL: WMTS-15R ASSEMBLY INSTRUCTIONS PAGE 6 15FT. TRIPOD WITH THE HELP AT AT LEAST TWO OTHER PEOPLE, TURN THE TRIPOD SO THAT THE HANDLE RAILS ARE FACING UP AND THE REAR LEG BRACES ARE ON THE GROUND. 16. Insert Top Ladder Section into Handle Rails 17.
Page 12
MODEL: WMTS-15R ASSEMBLY INSTRUCTIONS PAGE 7 15FT. TRIPOD W ITH THE HELP AT AT LEAST TWO OTHER PEOPLE , STAND THE TRIPOD UPRIGHT LEFT SIDE VIEW RIGHT SIDE VIEW 18. Attach another Cross Brace to Top Ladder Section 19. Attach the last Cross Brace...
Need help?
Do you have a question about the WMTS-15R and is the answer not in the manual?
Questions and answers