Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Westinghouse TR18361
Summary of Contents for Westinghouse TR18361
-
Page 1: Instruction Manual
INSTRUCTION MANUAL GASOLINE CHAIN SAW TR18361 3,000 0.325 INCHES GUIDE BAR GUIDE BAR ENGINE ENGINE CHAIN CHAIN FUEL TANK FUEL TANK Note: Before using our chain saws. please read this manual carefully to understand the proper use of your unit. Keep this manual handy. -
Page 2: Table Of Contents
SAFETY FIRST Instructions contained in warning swith in this manual marked with a symbol concern critical point swhich must be taken into consideration to prevent possible serious bodily injury, and fort his reason you are requested to read all such instructions carefully and follow them without fail. -
Page 3: Parts Location
1. PARTS LOCATION 1. Front guard 2. Starter knob 3. Air cleaner 4. Choke knob 5. Throttle interlock 6. Rear handle 7. Throttle trigger 8. Engine switch 9. Fuel tank 10. Oil tank 11. Front handle 12. Saw chain 13. Guide Bar 2. -
Page 4: Symbols On The Machine
WARNING Never remodel the product. We won’t warrant the machine, if you use the remodeled product or you don’t observe the proper usage written in the manual. 3. SYMBOLS ON THE MACHINE For safe operation and maintenance, symbols are carved in relief on the machine. According to these indicafions, please be careful not to make a mistake. - Page 5 exists that your judgment might be impaired or that you might not be able to operate the machine properly and in a safe manner. c. Avoid running the engine indoors. The exhaust gases contain harmful carbon monoxide. d. Never use the product under circumstances like those described below: 1.When the ground is slippery or when other conditions exist which might make it not possible to maintain a steady posture...
- Page 6 3.Things to notify your working area (Rope, warning signs) 4.Whistle (for collaboration or emergency) 5.Hatchet or saw (for removal of obstacles) c. Never use the product when wearing pants with loose cuffs, when wearing sandals, or when barefoot. WORKING CONSIDERING HANDLING OF FUEL a.
- Page 7 Before starting the engine, make sure the saw chain is not contacting anything. OPERATION Keep the handles dry, clean and free of oil or fuel mixture. Never touch the muffler, spark plug or other metallic parts of the engine while the engine is in operation or immediately after stopping the engine.
-
Page 8: Installing Guide Bar And Saw Chain
Do not overreach or cut above shoulder height. Follow manufactures sharpening and maintenance instructions for saw chain. Only use replacement bars and chains specified by the manufacturer or the equivalent. MAINTENANCE In order to maintain your product in proper working order, perform the maintenance and checking operations described in the manual at regular intervals. - Page 9 WARNING Th e s aw c h ai n h as v er y s h ar p e d g es . Us e t h i c k p r o t ec t i v e g l o v es f o r s af et y. Pull the guard towards the front handle to check that the chain brake is not on.
-
Page 10: Fuel And Chain Oil
NOTE A new chain will expand its length is the beginning of use. Check and readjust the tension frequently as a loose chain can easily derail or cause rapid wear of itself and the guide bar. 6. FUEL AND CHAIN OIL FUEL Mix a regular gasoline (leaded or unleaded, alcohol-free) and a quality-proven motor oil for air cooled 2 cycle... -
Page 11: Operating Engine
7. OPERATING ENGINE STARTING ENGINE Fill fuel and chain oil tanks respectively, and tighten the caps securely.(F7) Put the switch to “l” position.(F8) While holding the throttle lever together with the throttle interlock, push in the side throttle lock button and release the throttle lever to hold it at the starting position.(F9) Chain oil... - Page 12 in the figure.(F12) (1)Chain oil The chain oil flow can be changed by inserting a screwdriver in the hole on bottom of the clutch side. Adjust according to your work conditions. (F13) (1) Adjuster NOTE The oil tank should become nearly empty by the time fuel is used up.
- Page 13 5. Make a test cut and adjust the H needle for best cutting power, not for maximum speed. L needle H needle Idle adjusting screw CARBURETOR ANTI-FREEZE MECHANISM Operating the chain saw in temperatures of 0-5°C at times of high humidity may result in ice forming within the carburetor, and this in turn may cause the output power of the engine to be reduced or for the engine to fail to operate smoothly.
- Page 14 WARNING Continuing to use the product in anti-freeze mode even when temperatures have risen and returned to normal may result in the engine failing to start properly or in the engine failing to operate at its normal speed, and for this reason you should always be sure to return the unit to normal operating mode if there is no danger of icing occurring.
-
Page 15: Sawing
for a few minutes. 2.Put the switch to the “O” (STOP) position.(F18) (1) Switch 8.SAWING WARNING Before proceeding to your job, read “For Safe Operation” section. It is recommended to first practice sawing easy logs. This also helps you get accustomed to your unit. Always follow the safety regulations. - Page 16 It is extremely important that the chain brake be checked for proper operation before each use and that the chain be sharp in order to maintain the kickback safety level of this saw. Removal of the safety devices. Inadequate maintenance, or incorrect replacement of the bar or chain may increase the risk or serious personal injury due to kickback.
-
Page 17: Maintenance
the guide bar from being caught in the cut. A L o g l y i n g o n t h e g r o u n d (F21) Saw down halfway, then roll the log over and cut from the opposite side. A L o g h an g i n g o f f t h e g r o u n d (F22) In area A, saw up from the bottom one-third and finish by sawing down from the top. - Page 18 oiling pot for clogging.(F26) 3. Gu i d e b ar When the guide bar is dismounted, remove Saw dust in the bar groove and the oiling port.(F27) Grease the nose sprocket from the feeding port on the tip of the bar.(F28) (1) O i l i n g p o r t (2) G r eas e p o r t (3) S p r o c k et...
-
Page 19: Maintenance Of Saw Chain And Guide Bar
(1) S p r o c k et (2) N eed l e b ear i n g (3) C l u t c h d r u m (4) S p ac er (5) C l u t c h s h o e 4. - Page 20 Place your file on the cutter and push straight forward. Keep the file position as illustrated.(F32) After every cutter has been set, check the depth gauge and file it to the proper level as illustrated.(F33) WARNING Be sure to round off the front edge to reduce the chance of kickback or tie-strap breakage.
-
Page 21: Specifications
11. SPECIFICATIONS Chain saw Model 4600 Mass (without guide bar and chain) 7.5(kg) Dimensions (without guide bar and chain) 410 X 235 X 265(mm) Fuel Mixture (Gasoline 25: Two-cycleoil 1) Fuel tank capacity 550(ml) Chain oil Motor oil SAE#10W-30 Oil tank capacity 260(ml)3 Engine displacement 46(cm3) - Page 22 EXPLORE VIEW spark plug cylinder gasket blinker pistion ring upper cover screw pistion upper cover screw pistion pin snap ring cylinder plastic cover pistion pin switch plug carburator gasket muffler nut chain catcher muffler cover plate chain catcher screw screw turriform spring seat muffler assy turriform spring...
- Page 23 intake tube bracket oil pump screw intake tube bracket gasket oil pump assy intake flange oil pump dustproof filter cotton retaining ring small seal oil carburator assy breath nipple snap spring intake angle pipe filter cotton intake angle pipe stud breath nipple intake angle pipe shock absorption small plug pad...
- Page 24 stop switch wire clamp handle inner ring stop switch wire pressplate recoil spring idling speed regulating sleeve starter handle circlip for hole starter handle gasket HL sleeve rope left crank case handle left rubber cushioning pad handle screw screw ignition screw screw ignition assy big oil seal...
- Page 25 fuel oil filter assy spacer pin fuel oil pipe snap ring split washer fuel oil pipe spacer plate oil inlet tube rubber gasket fuel pipe split washer oil return pipe gasket oil pump support brake torsional spring rear handle chain brake lever lever trigger chain brake lever pin decorative cover...