Zipato Z Wave MULTISENSORQUAD User Manual

MULTISENSOR
QUAD
QUICK INSTALLATION GUIDE
v1.3
TRADEMARKS
Zipato and the Zipato logo are registered Trademarks. All
other product names mentioned herein may be trademarks or
registered trademarks of their respective companies.
NOTICE
Although Zipato has attempted to ensure the accuracy of the content
of this manual, it is possible that this document may contain technical
inaccuracies, typographical, or other errors. Zipato assumes no
liability for any error in this publication, and for damages, whether
direct, indirect, incidental, and consequential or otherwise, that may
result from such error, including, but not limited to loss of data or
profits. Zipato provides this publication "as is" without warranty of any
kind, either express or implied, including, but not limited to implied
warranties of merchantability or fitness for a particular purpose. The
published information in the manual is subject to change without
notice. Zipato reserves the right to make changes in the product
design, layout, and driver revisions without notification to its users.
This version of the Installation guide supersedes all previous versions.
ELECTROMAGNETIC COMPATIBILITY
In proper state and when operated properly, the product complies with
all the requirements in respect of interference radiation according
to EN 301 489-17, EN 301 489-1 and EN 300 328. The connections
conducting HF signals must neither be manipulated nor damaged.
TAKE CARE OF YOUR SAFETY
Display extreme caution when using ladders or steps, please
follow manufacturer's instructions. Be careful when using hand
and power tools and follow the manufacturer's guidelines when
using them. Take care that the correct tools are used. Wear
goggles or protective clothing where required.
INTRODUCTION
The 4 in 1 multi-sensor is designed to meet the requirement of
integrate 4 sensors into one housing:
(1) Door/window
(2) PIR
(3) illumination and
(4) temperature
When the detector is cooperated with security appliances, the (1) Door/
window or (2) PIR sensor act as an alarm detector. Alternatively, when
the detector is worked with Z-Wave controller, the detector can be
set to perform the role of home automation device by detecting both
changes in PIR motion detect or door/window open close signal with
percentage of illumination lux levels. One scenario is, once night falls,
the percentage of ambient illumination is lower than preset value. If
a person moves within or across the devices field of vision, a trigger
radio signal will be transmitted so as to turn connected lightings for
better illumination. Another scenario is to combine (1) Door/window (2)
PIR (3) illumination sensors to recognize people is coming in or going
out and turn the light on/off automatically. The temperature sensor
can detect the temperature so as to adjust heater or cooler to achieve
preset temperature or detect the abnormal environment temperature
(like freeze sensor or fire sensor) to send the warning message.
make your home smart
FIGURE 1
Dimensions (unit: mm)
ILLUMINATION 28.00
SENSOR LENS
1
Profile view
2
Top/bottom
view
FEATURES
(1) Door/window (2) PIR (3) illumination and (4) temperature
functions in one sensor
Adopt newest Z-wave 400 series chip, support multichannel
operation and higher data rate (9.6/40/100kbps)
Higher output power (+2.5dBm output power as compared to
-2.5dBm 300 series Z-wave module) to enhance the
communication range
1500mA CR123A lithium battery to guarantee 2 year battery life
Built in light sensor while applied to light control
Adopt Z-Wave protocol to secure the success of wireless two way
communication
With Tamper proof protection
Easy install
Low battery indication
Z-Wave V6.02
Z-Wave Certificated No PSM02-1 ZC08-13050003
Auto report the open/close status and battery status
FCC part15.249 / EN300 220-1/ certification
NCC
APPLICATION
Multisensor Quad is a special device combining both PIR and Door/
window functions. The benefits of combining Door/window with PIR
in one sensor can be observed in the following scenarios:
A
The ambient lighting would be lower than default setting
value after sunset. If the Multisensor Quad was installed on the
inner side of door in the house, Multisensor Quad would detect
www.zipato.com
28.00
10.00
3 4
Front view Back view
coming in people, then the light would be turned on for the better
illumination by radio transmission. Furthermore, Multisensor Quad
can be applied in a bathroom and it may turn on/off light and fan
automatically.
B
Multisensor Quad can be taken as a portal chime at front desk
of hotel or restaurant by sending out signal to IP-Gateway PSC01 as
reminder which can be connected with speaker to turn the volume
up. It can be kept silent when customer leaving.
C For SMEs (Small and medium enterprises), Multisensor Quad
plays an important role in working hours and non-working hours.
When non-working hours, Multisensor Quad plays as security
motion sensor, protects the office from intruders. At working hours,
4 in 1 sensor, can be applied to curtain or heater/cooler controller
for energy saving issue; although some people may use thermostat
to control heater/cooler however, Multisensor Quad sensor can
be smarter choice. Since it can detect the people's, activities, and
shutdown machine when no one exists or no movements.
D In the past, a digital home starter KIT includes many different
sensors with very high price. Right now, Using the 4 in 1 patented
sensor and a 4 in 1 gateway PSC01 (Siren + speaker + light + IP based
controller) carry out home "security" + "safety" + "automation"
in one box and provide customer full experience of digital life and
flexibility in installation with affordable price.
TECHNICAL SUPPORT
Having trouble installing your new product?
Zipato's website contains the latest user documentation and
software updates for Zipato products and services.
www.zipato.com
CONTACT SUPPORT
E-MAIL: support@zipato.com / (Mon-Fri) 9.00am-05.00pm (CET)
make your home smart
SPECIFICATION
POWER
OPERATING VOLTAGE STANDBY CURRENT
3V CR123A 48 uA
OPERATING CURRENT LOW BATTERY VOLTAGE
37mA 2.6V
RF
REGULATION
FCC part15.249 / EN300 220-1
DISTANCE
min. 40m indoor/min. 100m outdoor
MECHANICAL
WEIGHT DIMENSION (W x H x D)
Detector 28 x 96 x 23 mm
52 g
Magnet. 10 x 50 x 12 mm
BATTERY
CR123A BATTERY LIFE
1500mAh > 2 years
ENVIRONMENT
OPERATION TEMPERATURE HUMIDITY
Normal environment
temperature -10~ 40° C to
85%RH max
have better PIR and battery
performance
TEMPERATURE
DETECT RANGE
-10~70°C
ILLUMINATION
RANGE
0~500 LX
PIR DETECTION ANGLE
HORIZONTAL
0° 8~10M
90° 6~8M
HARDWARE
MAGNETIC GAP MAGNETIC GAP
(OPEN→CLOSE) (CLOSE→OPEN)
28 MM 30 MM
www.zipato.com 01