Advertisement
Quick Links
INTRODUCTION
Zipato PIR Motion Sensor is a passive infrared detector or physical sensor, the
sensor doesn't emit any energy, but only passively receive and detect infrared
radiation. Sensor sends messages via Z-Wave network to the Z-Wave main
PIR MOTION SENSOR
controller. In the communication between the PIR and Z-Wave main controller, PIR
sensor can only send messages and not receive them. When sensor is triggered, it
will send message to the main controller and associate devices to work through the
Z-Wave main controller. Sensor isbattery powered, small and can be installed
QUICK INSTALLATION GUIDE
easily.
v1.0
SPECIFICATION
Motion detection
Measure the light sensitivity
Compatible with 300 and 500 series
Range: up to 50m outdoor; 30m indoor
Power supply: CR123A x 1
Standby current: 16uA
Battery life: 1 year
Protocol: Z-Wave Plus
Detection range: 7 meters
Viewing angle: 110 degree
Operation temperature: 0 - 40 °C
Storage temperature: 0 - 60 °C
Size: 45 x 45 x 48 mm
www.zipato.com
TECHMICAL INFORMATION
• Use passive IR sensor to detect what is mocing
• When the sensor is triggered, LED light will flash in the detection area
• When there are people or animals moving in detection area, PIR sensor will send
alarm messages to the Z-Wave main controller
• Compatible with any Z-Wave main controller
PRODUCT CONFIGURATION
Inductive area
LED light
Holder
Sticker
PACKAGE CONTENT
PIR Motion Sensor - 1pc
Probe - 1pc
Holder - 1pc
User manual - 1pc
Battery - 1pc
Screw - 2pcs
Screw stopper - 2pcs
1.
INSTALLATION STEPS
• Holder installation
• Battery installation
• Fix PIR on the holder
HOLDER INSTALLATION
• OPTION 1
Fix the holder with screws
Battery
and screw stopper
Code button
BATTERY INSTALLATION
Screw stopper
Screw
DETECTION RANGE AND WORKING CONDITIONS
PIR Sensor has to be installed in a corner of the room or perpendicularly to the
2.
3.
doors. Actual detection range of the sensor can be influenced by environment
conditions. If there are false alarms, check for any moving objects withing the
sensor's detection area, such as trees blowing in the wind, cars passing by, etc.
False motion alarms may be caused by moving masses of air and heat as well. If
sensor keeps on reporting the false alarms, install the sensor in another place.
Work schematic diagram of PIR:
• OPTION 2
Fix the holder with double-sides
sticker
WORKING CONDITIONS
FIX PIR ON THE HOLDER
If there is someone moving withing the detection area, alarm will be triggered and
LED lights will flash in the inductive area at the same time.
4.
Advertisement
Summary of Contents for Zipato ne-nas-pd01z
- Page 1 Zipato PIR Motion Sensor is a passive infrared detector or physical sensor, the • When the sensor is triggered, LED light will flash in the detection area •...
- Page 2 LED STATUS controller, or Z-Wave gateway. supports: NOTIFICATION_REPORT_V4 2. ON / OFF DURATION 4. PIR DETECTION FUNCTION ENABLED / DISABLED 1. Remove the sensor cover This parameter can enable or disable the PIR sensor detecting function. 1. When sensor is triggered, LED flashes red once. 2.
- Page 3 Parameter number: 9 Event present: 0xFF command to the Z-Wave controller to inform that the motion sensor is in dead ZIPATO. THEY DO NOT, HOWEVER, AFFECT OR RESTRICT THE RIGHTS YOU HAVE Available settings: 0~1000 (Lux) Command class: COMMAND_CLASS_SENSOR_BINARY battery status, otherwise BATTERY_LEEL value range is 0% to 100%.
- Page 4 EN 300 220-1 V2.4.1:2012 “Countries in which this ZIPATO Limited Product Warranty applies”. The Limited LIMITED PRODUCT WARRANTY PERIOD product need not be new or of an identical make, model or part; ZIPATO may in its EN 300 220-2 V2.4.1:2012 COPYRIGHT Product Warranty will be honored in any country where ZIPATO or its authorized The Limited Product Warranty Period starts on the date of purchase from ZIPATO.