Advertisement
Quick Links
Advertisement
Related Manuals for Quest Engineering Q40
Summary of Contents for Quest Engineering Q40
- Page 1 QUEST m e t a l d e t e c t o r s...
- Page 2 IN THE BOX QUICK START...
- Page 3 ASSEMBLE QUICK START For the first time using. You need a philip screw driver to assemble the unit. Follow the steps illustrated and set a comfortable distance of the handle and tight the screws.
-
Page 4: Power On/Off
POWER ON/OFF QUICK START 1Sec... - Page 5 HEADPHONES/CHARGE QUICK START WIRE HEADPHONES WIRELESS HEADPHONES 1Sec On/Off After Powering on the Q40 and wireless headphones.Press the wireless function button on the right side of the control b ox once to activate them. The headphones have been pre- paired.If the headphones become unpai red anytime place them around 5” from t h e c o n t r o l b o x a n d...
-
Page 6: Speaker Volume
SPEAKER VOLUME QUICK START VOLUME + - 1 4Sec MUTE／MAX VOLUME... - Page 7 SENSITIVITY QUICK START Many things such as Power lines, Electric fences even buildings can cause Electrical Interference & Falsing when your detector is in use and there is no metal under the coil. Users can reduce the sensitivity by +／- ONE LEVEL pressing on the downward triangle button directly.Users can increase sensitivity when searching in low...
- Page 8 PROGRAM Level-up After powering on the detector to scroll through the various Programs, press and hold the Ground Balance button while at the same time scrolling with the Triangle buttons to arrive at the Programs you want. 1 and 2 are left for customize users own program.
- Page 9 PINPOINTING Level-up By pressing on the PINPOINT button(the round button with cross sign), the detector will enter a non- motion mode and alarm to target without moving the coil. Users can use this function to pinpoint target with cross action as illustrated. We strongly recommend to select the Xpointer for further assistance during digging to save the time.
-
Page 10: Ground Balancing
GROUND BALANCING Level-up The Q40 comes with Ground Balancing (GB) function. We recommend GB every time you change the detecting area. Make sure you have no metal targets under the coil while GB. Press and hold the square button while pumping the coil 6” (15cm) height to 1”... - Page 11 DISCRIMINATION Level-up Metal Detectors calculate the metal I.D. through the conductivity of the metal.Higher conductive metals such as silver show higher digit on the screen. Lower conductive such as Iron show lower on the scale usually under 25. Users can select or deselect some metal I.D.s to discriminate out undesired metal objects.
- Page 12 OTHERS Level-up FESEN. In Trashy areas some good signals may be muted together by an Iron FESEN signal.Users can turn the FESEN function on to have more chance to hear the good signals.It may cause more noise when FESEN has been activated. Ground Canceling Level.
-
Page 13: Troubleshooting
TROUBLE SHOOTING ？ NOT POWER ON No power, please recharge. Or contact with your dealer NO ALARM Coil not connect to the control box VERY NOISY Please find another place with less interference NO SOUND Make sure the Volume is not ZERO level FALSING WHEN Please confirm the coil cable is not broken SEARCHING IN GRASS... - Page 14 PRODUCTS CARE NOTICE! Do not twist the coil tail and connector to avoid wire damage. NOTICE! Do not store the device where prolonged exposure to extreme temperatures can occur to avoid device damage. NOTICE! Never use a hard or sharp object to operate the touch pad, or damage may result. NOTICE! Avoid chemical cleaners, solvents, and insect repellents that can damage plastic components and finishes.
- Page 15 YOUR VOICE REGISTER YOUR QUEST PLEASE TAKE A FEW MOMENTS TO ANSWER OUR QUESTIONS. THEY WILL HELP US DEVELOP NEW PRODUCTS FOR To register the Quest, please go to our website : THE FUTURE. www.QuestMetalDetectors.com click support, and register products to active your two year warranty. If you have 1 Why did you decide to buy a Deteknix difficulty to register online please contact with your dealer to detector?
- Page 16 Date Of Purchase Serial Number WARRANTY Title The Quest metal detectors is warranted against defects in Surname materials and workmanship under normal use for TWO years from the date of purchase to the original owner. First Name This warranty does not cover: •...
Need help?
Do you have a question about the Q40 and is the answer not in the manual?
Questions and answers