Adjustment After Replacing Drum Assembly (Video Heads); Check The Tape Travel After Reassembling Deck Assembly; Checking Audio And Rf Locking Time During Playback And After Cue Or Rev; Check For Tape Curling Or Jamming - Aiwa Microplate Reader Service Manual

QQ
3 7 63 1515 0
DECK MECHANISM ADJUSTMENT

7. Adjustment after Replacing Drum Assembly (Video Heads)

Purpose: To correct for shift in the Roller Guide and X value after replacing the Drum.
Test Equipment/ Fixture
• Oscilloscope
• Alignment tapes
• Blank Tape
• Post Height Adjusting Driver
• Screw Driver(+) Type 5mm
Checking/Adjustment Procedure
Play a blank tape and check for tape curling or creasing around
the roller guide. If there is a problem then follow the procedure
4. "Guide Roller Height" and 5. "Audio Control(A/C) Head
Adjustment".

8. Check the Tape Travel after Reassembling Deck Assembly.

TE
L 13942296513
8-1.Check Audio and RF Locking Time during playback and after CUE or REV (FF/REW)
Test Equipment/ Fixture
• Oscilloscope
• Alignment tapes(with 6H
3kHz Color Bar Signal)
• Stop Watch
Checking Procedure
Play an alignment tape then change the operating mode to
CUE or REV and confirm if the unit meets the above listed
specifications.

8-2.Check for tape curling or jamming

Test Equipment/ Fixture
• T-160 Tape
• T-120 Tape
Checking Procedure
1) Confirm that the tape runs smoothly around the roller
guides, drum and A/C head assemblies while abruptly
changing operating modes from Play to CUE or REV.
www
This is to be checked at the begining, middle and end
sections of the cassette.
.
http://www.xiaoyu163.com
Connection Point
• CH-1: PB RF Envelope
• CH-2: NTSC: SW 30Hz
PAL: SW 25Hz
• Head Swithching Output
Test Point
• RF Envelope Output Test Point
Specification
• RF Locking Time: Less than 5 sec.
• Audio Locking Time:Less than
10sec
• Be sure there is no tape jamming or curling
at the begining, middle or end of the tape.
x ao u163
y
i
http://www.xiaoyu163.com
2 9
8
Test Conditions
(Mechanism Condition)
• Play the blank tape
• Play an alignment tape
Connection Diagram
RF ENVELOPE OUTPUT TEST POINT
HEAD SWITCHING OUTPUT TEST
POINT
Waveform
V1/V MAX ≤ 0.7
V2/V MAX ≤ 0.8
RF ENVELOPE OUTPUT
Q Q
3 6 7 1 3 1 5
Test Equipment
Connection Points
Connection Points
• CH-1: PB RF Envelope
• CH-2: Audio Output
• RF Envelope Output Point
• Audio Ouptut Jack
NOTES:
1) CUE is fast forward mode (FF)
2) REV is the rewind mode (REW)
Specification
2) Confirm that the tape passes over the A/C head assem-
bly as indicated by proper audio reproduction and prop-
er tape counter performance.
co
.
72
9 4 2 8
Adjustment Points
• Guide Roller Precise
Adjustment
• Switching Point
• Tracking Preset
• X-Value
OSCILLOSCOPE
CH1 CH2
V1 V V2
Fig. C-7
0 5 8 2 9 9 4 2 8
Test Conditions
(Mecanism Condition)
• Play an alignment tape
(with 6H 3kHz Color Bar
Signal)
Test Conditions (Mecanism Condition) VCR(VCP) State
• Run the CUE, REV play mode at the
beginning and the end of the tape.
m
9 9
9 9