Page 1
http://www.xiaoyu163.com HV-FX9000 3 7 63 1515 0 REW/ /F FWD DA 4 HEAD/AUTO HEAD CLEANING/DIGITAL AUTO TRACKING PLAY REC/ITR PAUSE/ STILL STOP ONE TOUCH PLAYBACK SERVICE MANUAL L 13942296513 STEREO VIDEO BASIC VIDEO MECHANISM CASSETTE RECORDER : D33K-4HF/NT(6721R-0240A) This Service Manual is the "Revision Publishing" and replaces "Simple Manual" (S/M Code No.
http://www.xiaoyu163.com TABLE OF CONTENTS SPECIFICATIONS ............3 14. Reel S & Reel T ............59 3 7 63 1515 0 ACCESSORIES LIST ............3 15. Support CST ............60 DISASSEMBLY INSTRUCTIONS ........4 16. Base Assembly P4 ........... 60 SERVICE POSITION ............5 17.
http://www.xiaoyu163.com SPECIFICATIONS 3 7 63 1515 0 Video recording system Rotary 2 head herical scanning system Video S/N 43 dB (at SP) Video head Double azimuth 4 head Audio track 3 tracks (Hi-Fi sound 2 tracks, Normal Tuner system Frequency synthesized tuner sound 1 track) TV system Audio input...
http://www.xiaoyu163.com DISASSEMBLY INSTRUCTIONS 1. Top Case Removal 4. Mechanism Removal (see Fig. 3) 3 7 63 1515 0 1) Remove 4 screws holding the top case. 1) Disconnect the drum FF cable from the connector (PMD01) on the Main C.B. 2.
http://www.xiaoyu163.com SERVICE POSITION To set the mechanism to the service position in active status: 3 7 63 1515 0 Insert a spacer as shown below: The service position can be set in the stable status without any defective contact. MAIN C.B MECHA SPARSER 60mm...
http://www.xiaoyu163.com VCR TEST TAPE INTERCHANGEABILITY TABLE There are two types of the new allgnment tape CH-1B (for NTSC) and CH-2 (for PAL). On each tape four signals (1)-(4) 3 7 63 1515 0 are recorded for the times and in the order shown below. (1) : 8min.
http://www.xiaoyu163.com TRANSISTOR ILLUSTRATION 3 7 63 1515 0 E C B E C B E C B E C B 2SC5343 KTC4419 KTC3198 2SA928 2SC5344 KTC3199 KSC2328 KSR1003 KSR2003 KTA1266 KTC3203 L 13942296513 u163 http://www.xiaoyu163.com...
Page 12
http://www.xiaoyu163.com BLOCK DIAGRAM-2 (TUNER SECTION) 3 7 63 1515 0 AERIAL VHF/UHF RF OUT TU701 SW701 FROM POWER 5.2VA FROM POWER L 13942296513 JK301 LINE 1 VIDEO :VIDEO PB SIGNAL :VIDEO REC SIGNAL :AUDIO PB SIGNAL :AUDIO PB SIGNAL u163 http://www.xiaoyu163.com...
Page 28
http://www.xiaoyu163.com IC DESCRIPTION IC, GMS3977RAA98F 3 7 6 3 1 5 1 5 0 Pin No. Pin Name Description Pin No. Pin Name Description End sensor to detect the tape’s terminal (Lead taps section). TAKE UP KEY NAME A/D RANGE If “H”...
Page 29
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Description Output for the audio head switching 30Hz to the Hi-Fi circuits is made by inputting A.H.S/W 30 DPG, DFG signal through pin 38, 39 for switching Hi-Fi head. Refer to pin 24. Pulses output for switching video head A and B.
Page 30
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Description Vref (OSD) – GND. CV OUT The video signal is output to the RF modulator and line output jack. CHAR BIAS – GND. AFC LPF Horizontal sync is used to lock the OSD. (Reduce Jitter) AFC OSC Vss (OSD)
Page 31
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Description µ-COM main ground. Vss (SYS) – 1. 10MHz oscillator is used to generate the standard clock used to operate the µ-COM. OSC 1 2. When Vcc is applied, Oscillation occurs. (But, when “L” is applied to pin 89 in power failure, Oscillation stops.) OSC 2 1.
Page 32
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Description DRUM ADJ Pulse output to control drum motor in slow mode. 1. This pin receives remocon data through RC5F1, which amplifies and detects the R/C signal. 2. After input signal is decoded in µ-COM (IC501), and performs related key operation.
http://www.xiaoyu163.com IC BLOCK DIAGRAM IC, GMS3977RAA98F 3 7 63 1515 0 <OSD Section> COLOR BURST 4 fsc in 4/2 fsc BLUE VIDEO GENERATOR BLUE SIGNAL/ SIGNAL COLOR PHASE 4 fsc out LUMINANCE GEN. SYNC.SIGNAL GENERATOR BLUE BACK SUPERIMPOSE C.Vin SYNC.TIP Vref CLAMP Vchar...
http://www.xiaoyu163.com ADJUSTMENT Test Equipment 3 7 63 1515 0 • Oscilloscope • Test Tape • AC Millivolt Meter TTV-P1 Adjustment Location MAIN C.B (TOP VIEW) IC502 TU701 P3D01 P3D02 IC801 T101 IC301 W361 W362 H/SW PMC01 L 13942296513 IC501 MS501 VR501 PG ADJ.
Page 35
http://www.xiaoyu163.com 1. Servo Adjustment 3 7 63 1515 0 1) PG Adjustment MODE MEASUREMENT POINT ADJUSTMENT POINT SPECIFICATION PLAY VIDEO OUT 6.5 ± 0.5H VR501 (TTV-P1) H/SW (W361, W362) • Adjustment Procedure 1. Insert the PAL SP Test Tape (TTV-P1) and play. Note - Adjust the distance of X, pressing the Tracking(+) or Tracking(-) when the “ATR”...
http://www.xiaoyu163.com MECHANICAL MAIN PARTS LIST 1/1 3 7 63 1515 0 REF. NO PART NO. KANRI DESCRIPTION 1 S7-21R-F09-7D0 PANEL ASSY FRONT ————— PANEL FRONT 3 S4-426-81A-000 SPR,DOOR 4 S5-80R-003-2B0 DOOR CST ————— DECK ASSY VIDEO D33K ————— COVER BOTTOM —————...
http://www.xiaoyu163.com 3 7 63 1515 0 DECK MECHANISM DISASSEMBLY 2. Plate Assembly Top (Fig. A-2-1) 1) Unhook the (H1) and separate the Left Side. 2) Unhook the (H2) and lift up the Plate Assembly Top. NOTE (1) When reassembling, confirm (A),(B) Part of the Plate (H4) Assembly Top is inserted to the (L),(R) Grooves of the (H3)
http://www.xiaoyu163.com 3 7 63 1515 0 DECK MECHANISM DISASSEMBLY Spring S Brake Brake Assembly S (Fig. A-4-1) Arm Assembly Tension Reel T Spring Tension (Fig. A-4-5) Band Assembly (Fig. A-4-3) Spring T Brake Tension Reel S Brake Assembly T (Fig. A-4-2) (Fig.
http://www.xiaoyu163.com 3 7 63 1515 0 DECK MECHANISM ADJUSTMENT (FOR NORMAL MODELS) 1.Mechanism Alignment Position Check Purpose:To determine if the Mechanism is in the correct position, when a Tape is ejected. Test Conditions (Mechanism Test Equipment/ Fixture Check Point Condition) •...
http://www.xiaoyu163.com 3 7 63 1515 0 DECK MECHANISM ADJUSTMENT 2. Preparation for Adjustment (To set the Cassette without Tape. Cover the Holes of the End Sensors at the both sides of the Deck Mechanism to the Loading state Bracket Side(L) and Bracket Assembly Door to prevent a without inserting a Cassette Tape).
http://www.xiaoyu163.com 3 7 63 1515 0 DECK MECHANISM ADJUSTMENT 4.Guide Roller Height Adjustment Purpose: To regulate the Height of the Tape so that the Bottom of the Tape runs along the Tape Guide Line on the Lower Drum. 4-1. Preliminary Adjustment Test Equipment/ Fixture Test Conditions (Mechanism Condition) Adjustment Point...
http://www.xiaoyu163.com 3 7 63 1515 0 DECK MECHANISM ADJUSTMENT 5. Audio/Control (A/C) Head Adjustment Purpose: To insure that the Tape passes accurately over the Audio and Control Tracks in exact Alignment in both the Record and Playback Modes. 5-1. Preliminary Adjustment (Height and Tilt Adjustment) Perform the Preliminary Adjustment, when there is no Audio Output Signal with the Alignment Tape.
http://www.xiaoyu163.com 3 7 63 1515 0 DECK MECHANISM ADJUSTMENT 5-2. Confirm that the Tape passes smoothly slowly turn the Tilt Adjustment Screw(C) in the Counterclockwise direction. between the Take-up Guide and Pinch Roller(using a Mirror or the naked eye). Afetr completing Step 5-1.(Preliminary Adjustment), NOTE: check that the Tape passes around the Take-up Guide and Pinch Roller without Folding or Curling at the Top or...
http://www.xiaoyu163.com 3 7 63 1515 0 DECK MECHANISM ADJUSTMENT 7. Adjustment after Replacing Drum Assembly (Video Heads) Purpose: To correct for shift in the Roller Guide and X value after replacing the Drum. Test Conditions Test Equipment/ Fixture Connection Point Adjustment Points (Mechanism Condition) •...
http://www.xiaoyu163.com 3 7 63 1515 0 MAINTENANCE/INSPECTION PROCEDURE (FOR NORMAL MODELS) 1 Check before starting repairs The following faults can be remedied by cleaning and oiling. Check the needed lubrication and the conditions of cleanli- ness in the unit. Check with the customer to find out how often the unit is used, and then determine that the unit is ready for inspection and maintenance.
http://www.xiaoyu163.com 3 7 63 1515 0 MAINTENANCE/INSPECTION PROCEDURE 4. Supplies Required for Inspection and 2. Required Maintenance Maintence The recording density of a VCR(VCP) is much higher than that of an audio tape recorder. VCR(VCP) components must (1) Grease : Kanto G-311G (Blue) or equivalent be very precise, at tolerances of 1/1000mm, to ensure com- (2) Isopropyl Alcohol or equivalent patiblity with other VCRs.
http://www.xiaoyu163.com 3 7 63 1515 0 MAINTENANCE/INSPECTION PROCEDURE (2) Periodic greasing 5-2) Greasing Grease specified locations every 5,000 hours. (1) Greasing guidelines Apply grease, with a cleaning patch. Do not use excess 1) Loading Path Inside & Top side 5) Lever Tension Groove grease.
http://www.xiaoyu163.com 3 7 63 1515 0 MECHANISM TROUBLESHOOTING GUIDE 1.Deck Mechanism Auto REW doesn't work. Is the output of END sensor of supply side "H"? “H”: more than 3.5V “L”: less than 0.7V~1V Is the Vcc. voltage of End Check the syscon power. sensor 5V? Replace End sensor.
Page 67
http://www.xiaoyu163.com 3 7 63 1515 0 MECHANISM TROUBLESHOOTING GUIDE AUTO STOP. (PLAY/CUE/REV) Check aligment positions (page 67) Check spring Pinch. In Play/Cue/Rev is the pinch roller in contact with the capstan Is the output of DFG, DPG OK? Replace Drum Motor. shaft.
Page 68
http://www.xiaoyu163.com 3 7 63 1515 0 MECHANISM TROUBLESHOOTING GUIDE In PB mode Tape Presence not sensed. Is the Pinch Roller attached Check Alignment positions to the Capstan Motor Shaft? (page 67) Does the T/Up Is the Belt ok? Replace the Belt. Reel turn? Check the clutch and the Idler Does the Capstan Motor turn?
http://www.xiaoyu163.com 3 7 63 1515 0 MECHANISM TROUBLESHOOTING GUIDE 2. Front Loading Mechanism Cassette cannot be inserted. Is the Lever Switch Spring Replace or add the Does the Lever Switch work? damaged or omitted? Lever Switch Spring. Does the F/L switch work Replace F/L Switch.
Page 70
http://www.xiaoyu163.com 3 7 63 1515 0 MECHANISM TROUBLESHOOTING GUIDE Cassette will not load. Does the CST insert? Does the opener Lid work? Replace the Opener Lid. Does the Gear Rack F/L work? Replace the Rear Rack F/L. Does the Opener Door work? L 13942296513 Does the Arm Assembly F/L work? Is the opener Door assembled correctly?
Page 71
http://www.xiaoyu163.com 3 7 63 1515 0 L 13942296513 u163 2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110-8710, JAPAN TEL:03 (3827) 3111 931196 Printed in Singapore http://www.xiaoyu163.com...