Related Manuals for Pulse Secure PSA7000
Summary of Contents for Pulse Secure PSA7000
- Page 1 PSA7000 Hardware Guide Pu u b b lish h e e d Da a t t e September 2017 Document Revision...
- Page 2 Copyright © 2014-2017, Pulse Secure, LLC. All rights reserved. All trademarks are the property of their respective owners. All specifications are subject to change without notice. Pulse Secure, LLC assumes no responsibility for any inaccuracies in this document. Pulse Secure, LLC reserves the right to change, modify, transfer, or otherwise revise this publication without notice.
-
Page 3: Table Of Contents
Licensing the System ..................................22 Installation and Management....................23 Unpacking the System ................................23 Rack Mounting ....................................23 Choosing a Setup Location .............................23 Rack Mounting Instructions ............................24 Installation Procedure ..............................25 Installing and Removing Hard Drives ............................28 © 2017 Pulse Secure, LLC. All rights reserved... - Page 4 Comply with Local and National Electrical Codes .........................46 Product Disposal...................................47 Hot Swap Fan Warning ................................48 Power Cable and AC Adapter ..............................50 Certification Statements ................................52 Japan .....................................52 Israel ......................................52 Saudi Arabia ..................................52 South Korea ..................................52 Taiwan ....................................52 Thailand ....................................53 © 2017 Pulse Secure, LLC. All rights reserved...
-
Page 5: System Overview
System Overview Introduction The PSA7000 offers a 17.7" short-depth 2U foot-print with advanced air flow thermal control and two rear hot- swappable drivebays. Below is the front and rear view of the system. The disk drives (HDD1 and HDD2) and power supplies (PWR1 and PWR2) are accessible from the rear. -
Page 6: Led Control Panel
An overheat condition has occurred. This may be caused by the cable congestion. Blinking red (1Hz) Fan failure; check for an inoperative fan. Blinking red (0.25Hz) Power failure; check for a non-operational power supply. © 2017 Pulse Secure, LLC. All rights reserved... - Page 7 Power: Indicates the power is being supplied to the system power supply. This LED should be illuminated when the system is operating. Power Failure: When this LED flashes, it indicates a power failure in the power supply. © 2017 Pulse Secure, LLC. All rights reserved...
-
Page 8: Management Port Leds
The PSA7000C has four INT/EXT copper LAN ports located on the front. Each Ethernet port has two LEDs: Color Description Activity Green (flashing) LAN active Link 100 Mbps link speed or no connection Amber 1 Gbps link speed Green 10 Gbps link speed © 2017 Pulse Secure, LLC. All rights reserved... -
Page 9: Beeping And Alarms
RED) Continuous beep (Power failure a) Both power supply modules connected but one power cord LED comes on, Front panel) connected b) One of the two power supplies has failed © 2017 Pulse Secure, LLC. All rights reserved... -
Page 10: Sata Drives
The LCD supports a Display mode (default) and Menu mode. The Display mode describes the current state of the system, such as normal state or error conditions (example, fan speed and overheat). Use the directional buttons to access the Menu mode and find the device information. © 2017 Pulse Secure, LLC. All rights reserved... -
Page 11: Lcd Modes
LCD remains in Display mode. If the LCD is in Menu mode and the user does not press any button for more than two minutes, then the LCD changes back to Display mode. © 2017 Pulse Secure, LLC. All rights reserved... -
Page 12: Display Mode
If all systems are functioning normally, then the LCD shows NORMAL. The second line in the NORMAL state is used to show whether the appliance is configured as part of a cluster. The valid states are Clustering OFF and Clustering ON. © 2017 Pulse Secure, LLC. All rights reserved... - Page 13 If more than one error condition is detected, all error conditions will be displayed in sequence with a two seconds’ pause before switching to the next one. All error conditions are cleared prior to return to the NORMAL state. Error conditions include: • Overheat • Fan Failure • RAID Errors © 2017 Pulse Secure, LLC. All rights reserved...
-
Page 14: Menu Mode
Internal IP and going clockwise. Pressing Cancel at any point exits to the Display mode. If Internal IP and External IP are not used, they will show Disabled instead of showing the IP address. © 2017 Pulse Secure, LLC. All rights reserved... -
Page 15: Hardware Specifications
700W Input frequency range 50 - 60Hz In the unlikely event that your power supply fails, replacement is simple and can be done without tools. The power supplies are redundant and hot-swappable. © 2017 Pulse Secure, LLC. All rights reserved... -
Page 16: Environmental Requirements
Listed below are the supported detached 10Gb/s SFP+ fiber transceivers: Avago AFBR-709DMZ • Cisco SFP-10G-SR-S Module (S-Class) • Cisco SFP-10G-SR Module • Juniper EX-SFP-10GE-SR • HP X132 10G SFP+ LC SR • © 2017 Pulse Secure, LLC. All rights reserved... -
Page 17: Mounting Rails
PSA7000 Hardware Guide Mounting Rails The PSA7000 can be placed in a rack for secure storage and use. To set up your rack, follow the step-by-step instructions included in this manual. Where to Get Replacement Components Although not frequently, you may need replacement parts for your system. To ensure the highest level of professional service and technical support, go to https://www.pulsesecure.net/support/. -
Page 18: Console And Initial Configuration
9600 speed, 8 data bits, 1 stop bit, no flow control. To find your COM port in Windows, go to Start > Search > Device Manger > Ports (COM & LPT) > USB Serial Port (COM#). © 2017 Pulse Secure, LLC. All rights reserved... -
Page 19: Power On The System
After entering these settings, you can continue configuring the PSA7000 through the administrator Web console. During this basic setup process, you define the “personality” of the PSA7000. For example, you can set up the PSA7000 to act as a Pulse Connect Secure device, Pulse Policy Secure device, or Pulse One Service. - Page 20 Enter random text (used for authentication certificate) After you perform the basic setup, you are ready to license the software, verify accessibility, and complete the configuration process through the PSA7000 administrator Web console. © 2017 Pulse Secure, LLC. All rights reserved...
-
Page 21: Change The Personality
Changing a personality deletes all configuration files and system and user data. You must perform the basic setup again to reestablish network connectivity. The installation process may take up to 20 minutes. Note: If PSA7000 is set up as Pulse Connect Secure or Pulse Policy Secure device, it can be switched to any other personality anytime. -
Page 22: Access The Web Admin Interface
Licensing the System After you install the device and perform basic setup, you are ready to license it. To license your device, follow instructions received in an email from Pulse Secure. For more information, see https://www.pulsesecure.net/support. The device uses the common machine and organization names to create a self-signed digital certificate for use during product evaluation and initial setup. -
Page 23: Installation And Management
Always make sure the rack is stable before extending a component from the rack. • You should extend only one component at a time - extending two or more simultaneously may cause the rack to become unstable. © 2017 Pulse Secure, LLC. All rights reserved... -
Page 24: Rack Mounting Instructions
Reliable Ground — A reliable ground must be maintained always. To ensure this, the rack itself should be grounded. Attention should be given to power supply connections other than the direct connections to the branch circuit (i.e. the use of power strips, etc.). © 2017 Pulse Secure, LLC. All rights reserved... -
Page 25: Installation Procedure
Step 1 - Identify the Parts There is a left and right rail assembly for the PSA7000, as marked by the (L) and (R) stickers on the inner rails: Each assembly has 3 parts: inner rail, middle rail, and outer rail. - Page 26 PSA7000 Hardware Guide Step 3 - Attach the Inner Rails Attach the inner rails to the sides of the PSA7000: The tabs on the side of the chassis slide into the rails. Press down hard on the area shown in the picture, then slide the inner rail forward, pushing firmly until it clicks into the locked position.
- Page 27 Step 5 - Mount the Chassis Extend the middle rails. Then, lift the PSA7000 and slide the ends of the outer rails into the middle rails: As you’re sliding it, press the locking tabs down on both sides of the chassis. The rails will lock into place: Note: You may require two people to safely mount the chassis.
-
Page 28: Installing And Removing Hard Drives
Close the drive tray handle until it clicks into place. Note: Replacing a failed hard drive requires manual configuration steps to be taken in the admin console. See the Administration Guide for more information at https://www.pulsesecure.net/techpubs. © 2017 Pulse Secure, LLC. All rights reserved... -
Page 29: Replacing Power Supplies
Replacing Power Supplies The PSA7000 chassis has a 700 Watt power supply. This power supply is auto-switching capable. This enables it to automatically sense and operate at a 100v to 240v input voltage. An amber light will be illuminated on the power supply when the power is off. -
Page 30: Network Cables
This appliance offer dual and redundant 10G network interface ports (4 ports total) in the SFP+ form factor. Pulse Secure has qualified SFP+/Cable combinations (Short Range, 850 nm) and offers them for sale as an optional accessory. Check the Price book for the SKUs. -
Page 31: Psa7000C
The Network interface card in the PSA7000f is designed for 10G networks, but it can support 1G networks when used with 1G transceivers at both ends of the network. No manual set up is required. Pulse Secure does not offer any optional 1G transceiver / cable as an option for sale. Any supplier’s short range 1G transceiver should work. -
Page 32: Standard Warnings And Compliance
The following statements are industry standard warnings, provided to warn the user of situations that have the potential for bodily injury. Should you have questions or have trouble, contact Pulse Secure's Technical Support department for assistance. Only certified technicians should attempt to install or configure components. -
Page 33: General Safety
警告の定義 この警告サインは危険を意味します。 人身事故につながる可能性がありますので、 いずれの機器でも動作させる前に、 電気回路に含まれる危険性に注意して、 標準的な事故防止策に精通して下さい。 此警告符号代表危 。 您正处于可能受到 重 害的工作环境中。在您使用 始工作之前，必 充分意 到触 的危 ，并熟 掌握防止事故 生的 准工作程序。 根据 每 警告 尾的声明号 找到此 的安全性警告 明的翻 文本。 此警告符號代表危險。 您正處於可能身體可能會受損傷的工作環境中。在您使用任何設備之前，請注意觸電的危險，並且要熟悉預防事故發生的標準工作程序。請 依照每一注意事項後的號碼找到相關的翻譯說明內容。 © 2017 Pulse Secure, LLC. All rights reserved... - Page 34 פיזית אפשרית. במידה ויש שאלות או היתקלות בבעיה כלשהי, יש ליצור קשר עם מחלקת תמיכה .טכנית של סופרמיקרו. טכנאים מוסמכים בלבד רשאים להתקין או להגדיר את הרכיבים .יש לקרוא את הנספח במלואו לפני התקנת או הגדרת הרכיבים במארזי סופרמיקרו © 2017 Pulse Secure, LLC. All rights reserved...
- Page 35 Gebruik de nummers aan het eind van elke waarschuwing om deze te herleiden naar de desbetreffende locatie. BEWAAR DEZE INSTRUCTIES © 2017 Pulse Secure, LLC. All rights reserved...
-
Page 36: Installation Instructions
.יש לקרוא את הוראות התקנה לפני חיבור המערכת למקור מתח اقر إرشادات التركيب قبل توصيل النظام إلى مصدر للطاقة 시스템을 전원에 연결하기 전에 설치 안내를 읽어주십시오. Waarschuwing Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron aansluit. © 2017 Pulse Secure, LLC. All rights reserved... -
Page 37: Circuit Breaker
המכשיר המגן מפני הקצר החשמלי הוא לא יותר מ 20 V, 250 هذا المنتج يعتمد على معداث الحمايت مه الدوائرالقصيرة التي تم تثبيتها في المبنى :تأكد من أن تقييم الجهاز الوقائي ليس أكثر من V 20A, © 2017 Pulse Secure, LLC. All rights reserved... -
Page 38: Power Disconnection Warning
Warnung Das System muss von allen Quellen der Energie und vom Netzanschlusskabel getrennt sein, das von den Spg.Versorgungsteilmodulen entfernt wird, bevor es auf den Chassisinnenraum zurückgreift, um Systemsbestandteile anzubringen oder zu entfernen. © 2017 Pulse Secure, LLC. All rights reserved... - Page 39 Voordat u toegang neemt tot het binnenwerk van de behuizing voor het installeren of verwijderen van systeem onderdelen, dient u alle spanningsbronnen en alle stroomkabels aangesloten op de voeding(en) van de behuizing te verwijderen © 2017 Pulse Secure, LLC. All rights reserved...
-
Page 40: Equipment Installation
.צוות מוסמך בלבד רשאי להתקין, להחליף את הציוד או לתת שירות עבור הציוד لتزكيب واستبدال أو خدمة هذا الجهاس يجب أن يسمح فقط للمىظفيه المؤهليه والمدربيه 경고! 훈련을 받고 공인된 기술자만이 이 장비의 설치, 교체 또는 서비스를 수행할 수 있습니다. © 2017 Pulse Secure, LLC. All rights reserved... -
Page 41: Restricted Area
(This warning does not apply to workstations). アクセス制限区域 このユニッ トは、 アクセス制限区域に設置されるこ とを想定しています。 アクセス制限区域は、 特別なツール、 鍵と錠前、 その他のセキュ リティの手段を用いてのみ出入りが可能です。 警告 此部件 安 在限制 出的 所，限制 出的 所指只能通过使用特殊工具、 和 匙或其它安全手段 出的 所。 警告 此裝置僅限安裝於進出管制區域，進出管制區域係指僅能以特殊工具、鎖頭及鑰匙或其他安全方式才能進入的區域。 © 2017 Pulse Secure, LLC. All rights reserved... - Page 42 Dit apparaat is bedoeld voor installatie in gebieden met een beperkte toegang. Toegang tot dergelijke gebieden kunnen alleen verkregen worden door gebruik te maken van speciaal gereedschap, slot en sleutel of andere veiligheidsmaatregelen. © 2017 Pulse Secure, LLC. All rights reserved...
-
Page 43: Redundant Power Supplies
électrique de l'unité, toutes les connexions d'alimentation doivent être débranchées. אם קיים יותר מספק אחד !אזהרה ליחדה יש יותר מחיבור אחד של ספק. יש להסיר את כל החיבורים על מנת לרוקן .את היחידה © 2017 Pulse Secure, LLC. All rights reserved... -
Page 44: Backplane Voltage
Cuando el sistema está en funcionamiento, el voltaje del plano trasero es peligroso. Tenga cuidado cuando lo revise. Attention Lorsque le système est en fonctionnement, des tensions électriques circulent sur le fond de panier. Prendre des précautions lors de la maintenance. © 2017 Pulse Secure, LLC. All rights reserved... -
Page 45: Comply With Local And National Electrical Codes
機器の取り付けはその地方および国の電気規格に準拠する必要があり ます。 警告 安 必 符合本地与本国 气法 。 警告 Warnung Die Installation der Geräte muss den Sicherheitsstandards entsprechen. ¡Advertencia! La instalacion del equipo debe cumplir con las normas de electricidad locales y nacionales. © 2017 Pulse Secure, LLC. All rights reserved... -
Page 46: Product Disposal
Ultimate disposal of this product should be handled according to all national laws and regulations. 製品の廃棄 この製品を廃棄処分する場合、 国の関係する全ての法律 ・ 条例に従い処理する必要があります。 警告 本 品的 弃处理 根据所有国家的法律和 章 行。 警告 本產品的廢棄處理應根據所有國家的法律和規章進行。 Warnung Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen des Landes erfolgen. © 2017 Pulse Secure, LLC. All rights reserved... -
Page 47: Hot Swap Fan Warning
ファン ・ ホッ トスワップの警告 シャーシから冷却ファン装置を取り外した際、 ファンがまだ回転している可能性があります。 ファンの開口部に、 指、 ドライバー、 およびその他のも のを近づけないで下さい。 警告 当您从机架移除 扇 置， 扇可能仍在 动。小心不要将手指、螺 起子和其他物品太靠近 扇 警告 © 2017 Pulse Secure, LLC. All rights reserved... - Page 48 Het is mogelijk dat de ventilator nog draait tijdens het verwijderen van het ventilatorsamenstel uit het chassis. Houd uw vingers, schroevendraaiers en eventuele andere voorwerpen uit de buurt van de openingen in de ventilatorbehuizing. © 2017 Pulse Secure, LLC. All rights reserved...
-
Page 49: Power Cable And Ac Adapter
Netzteile. Verwendung anderer Kabel und Adapter kann zu einer Fehlfunktion oder ein Brand entstehen. Elektrische Geräte und Material Safety Law verbietet die Verwendung von UL-oder CSA-zertifizierte Kabel, UL oder CSA auf der Code für alle anderen elektrischen Geräte als Produkte von Pulse Secure nur bezeichnet gezeigt haben. - Page 50 Appareils électroménagers et de loi sur la sécurité Matériel interdit l'utilisation de UL ou CSA câbles certifiés qui ont UL ou CSA indiqué sur le code pour tous les autres appareils électriques que les produits désignés par Pulse Secure seulement. חשמליים ומתאמי...
-
Page 51: Certification Statements
South Korea 이 기기는 업무용(A급) 전자파 적합기기로서 판매자 또는 사용자는 이 점을 주의하시기 바라며, 가정외의 지역에서 사용하는 것을 목적으로 합니다. Taiwan 警告使用者 ： 這是甲類的資訊產品 ， 在居住的環境中使用時 ， 可能會造成射頻干擾 ， 在這種情況下 ， 使用者會被要求採取某 些適當的對策 © 2017 Pulse Secure, LLC. All rights reserved... -
Page 52: Thailand
PSA7000 Hardware Guide Thailand เครื ่ อ งโทรคมนาคม และอุ ป กรณ์ น ี ้ มี ค วามสอดคล้ อ งตามข้ อ ก าหนดของ กทช. © 2017 Pulse Secure, LLC. All rights reserved...
Need help?
Do you have a question about the PSA7000 and is the answer not in the manual?
Questions and answers