Advertisement
Configuration and installation processor guide
ELECTRONICS
Ch6 Ch5 Ch4 Ch3 Ch2 Ch1 ESC
PX- 2
Ch6
Ch5
Ch4
Ch3
Ch2
The power supply wires (GND and +12v) and the remote wire (IN and OUT) may use
0,5mm² gauge (24awg) or bigger.
The REMOTE IN comes from player and the REMOTE OUT wired to the signal from
the amplifiers. This connection is necessary for correct operation of the system.
Input voltage: +10v to 15v.
Current Consumption: 0,35A.
The installation must be done in a local covered and ventilated place and without
vibration.
The processor has 8 buttons to configure as the owner wish.
Encoder: Correspond to 28 bands for equalization.
CH: Allow accessing the 6 channels.
ESC: Return to initial display.
EXPERT
Initial display:
ELECTRONICS
1. HOW TO CONFIGURE THE EQUALIZER:
Press the ESC button to go initial display, turn the encoder until EQ IN.
In the display the user can see:
1º Step:
2º Step:
Freq: 31Hz
EQ IN
=>
G: 0dB
Press the Encoder.
Turn the Encoder:
The gain level has
steps of 1dB and
limited between -12dB
and 12dB.
1
3
EXPERT
FUNC
6 CH
46 - EQ
LIMITER
OUT
Ch1
IN L
IN R
L
R
3º Step:
4º Step:
Freq: 63Hz
Freq: 40Hz
=>G: 0dB
=>G: 0dB
Press the Encoder:
Repeat the 2º and 3º
steps to configure
other 27 frequencies.
Press the Encoder to
change the equalizer's
frequency.
Configuration and installation processor guide
2. HOW TO CONFIGURE THE PRESETS (CUSTOM1, CUSTOM2, CUSTOM3):
Press ESC to go initial display and then turn or press the encoder until
CROSS/EQ/LIM/ALL CUSTOM, the user can see:
1º Step:
2º Step:
CROSS/EQ/LIM/ALL
EQUALIZER
CUSTOM
CUSTOM 1
Press or turn the
See the display
encoder.
changed to next user's
definition (CUSTOM2),
now the user can
configure a new preset
that will be saved in
memory selected.
3. HOW TO EQUALIZER CHANNELS (CH1, CH2 , CH3, CH4, CH5 CH6):
Press the ESC button to go initial display.
Turn the Encoder until the EQ CH function.
1º Step: Channels
2º Step: Choose the freq
EQ CH
F1: 500 Hz
Turn the Encoder:
Press the CH to be
equalized.
Press the Encoder to
choose the Q (quality)
factor.
4. HOW TO CONFIGURE THE CHANNELS:
Press the ESC button to go initial display.
Turn the Encoder until the Routing Channel function:
1º Step: Channels
2º Step: Choose the Input
Routing
OUT
Channel
CH1: R
Press to choose the
Turn the Encoder:
channel to be routing.
Choose L, R or L+R
(mono). Press ESC to
go back, choose the
next channel and
repeat the 1 and 2
steps or choose the
function.
3º Step:
EQUALIZER
OBS: the user's
CUSTOM 2
definitions save
others
For accessing the next
configurations
memory, repeat the
changed on
first and second steps.
processor, and
not just the
equalizer.
3º Step: Choose the Q
4º Step: Choose the Gain
Q1: 2.0
G1: 0 dB
Turn the Encoder:
Turn the Encoder:
Press the Encoder to
Turn up or down the
choose the level gain.
gain level. Repeat the
steps 2, 3 and 4 to
configure the others
ones.
:
4
Advertisement
