ElproSys DiagProg4 Instruction Manual
Tester
Hide thumbs
Also See for DiagProg4:
- Instruction manual (29 pages) ,
- Instruction manual (17 pages) ,
- Instruction manual (18 pages)
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ElproSys DiagProg4
Summary of Contents for ElproSys DiagProg4
- Page 1 Instruction manual DIAGNOSTIC TESTER Diagnostic tester Instruction Manual ENGLISH Prepared by: Sylwester Czupryna Approved by: Sebastian Żur ElproSys Sp. z o.o. ul. Tarnogórska 140 44-102 Gliwice © ElproSys April, 2017 − Rev. 3.0...
-
Page 2: Table Of Contents
Tools - description of functions ..................... 13 Power supply......................... 15 Memory card......................... 16 WiFi connection ........................17 Light sensor ........................... 17 DiagProg4 connection with PC (USB) ..................17 DISPLAY FIRMWARE UPDATE ....................18 RESTART DIAGPROG4 ......................18 DIAGPROG4 MANAGER ......................19 DIAGPROG4 TEST ........................20 TECHNICAL DATA........................ -
Page 3: Safety Principles And Rules
This manual does not take into account local regulations. The user is solely responsible for the compliance with the local regulations. ATTENTION Any repair work must be carried out by ElproSys company or its authorized dealer. Failure to comply with it may result in loss of warranty. ATTENTION Please store this instruction manual in a safe place. -
Page 4: Preliminaries
ElproSys company or its authorized representative. Switching on and off the device DiagProg4 device does not have a switch. In order to switch on / off the device power cable should be connected / disconnected. -
Page 5: The First Use
Instruction manual DIAGNOSTIC TESTER THE FIRST USE DiagProg4 delivered to the client remains inactive and is a demo version. In order for the device to be fully active please complete the following steps. 1. Activation AUTOMATIC ACTIVATION In order to activate DiagProg4 connect the device to WIFI network a select from DP4 menu: SETUP →... -
Page 6: Diagprog4 - Description
Instruction manual DIAGNOSTIC TESTER DIAGPROG4 - DESCRIPTION Please find below some information about DiagProg4 that will help familiarise with the product. Table 1 - Display - technical parameters TECHNICAL PARAMETERS Dimensions 7’ (165 mm x 104.44 mm x 6.76 mm) -
Page 7: Text And Value Entry
Instruction manual DIAGNOSTIC TESTER TEXT AND VALUE ENTRY DiagProg4 allows to enter text and numeric values according to the nature of the activities. 1. Text input is done using alphanumeric keypad. Delete entered text Start of a new line Distance between characters 2. - Page 8 Instruction manual DIAGNOSTIC TESTER *Above screenshots and colours of the device may differ from the actual product. © ElproSys April, 2017 − Rev. 3.0...
-
Page 9: Signaling Leds
NETWORK Indicates WiFi network connection. BUTTONS Most buttons in DiagProg4 are virtual buttons on the display. Actual buttons „Top”, „Bottom”, „Accept” and „Cancel” are located on the cover of the device. Table 2 - Navigation buttons (on the cover) BUTTON FUNCTION „Top/Front”... - Page 10 Allows to clear accident data in Airbag modules Read/Write EEPROM Allows to read and write full EEPROM content Read/Write FLASH Enables to read and write full FLASH content Advanced diagnostic Programing modules at the advanced level functions © ElproSys April, 2017 − Rev. 3.0...
-
Page 11: Setup - Description Of Functions
DEFAULT SETTINGS initially used DOWNLOAD UPDATE/ ACTIVATION Allows user to check for new updates/ activations INFORMATION Information about DiagProg4 Menu language selection: Polish, English, German, LANGUAGE French, Italian, Spanish, Portuguese, Brazilian File synchronisation between device and files on the MAINTENANCE... - Page 12 DATE/TIME Automatic information about date, time ATTENTION DiagProg4 shows Central European Time (UTC+1). Time and date may be incorrect while staying in different time zones. DEVICE LIMITS Information about DiagProg4 time lock AGREEMENT OF USE Information about DiagProg4 agreement of use...
-
Page 13: Tools - Description Of Functions
K-L ANALYZER (Internal use only) Programs For Internal Use Only MICROCONTROLLER PROGRAMMER Write FLASH + EEPROM Immediate restart in order to reload operating RESTART DIAGPROG4 system RESTORE THE BACKUP MODULE Restore backup file saved on SD card © ElproSys April, 2017 − Rev. 3.0... - Page 14 Instruction manual DIAGNOSTIC TESTER SENDING LOG FILE Send *.LOG file to ElproSys server for technical support SUPPORT SCRIPT Runs support script prepared for user by technical support team UDS COMMUNICATION CONTROL Enables/ disables UDS communication UNIT CALCULATOR Enables metric conversion ©...
-
Page 15: Power Supply
(+) inside For more detailed information on power supply please go to “Technical data” section on page 21 Picture below shows correct power supply connection to DiagProg4 together with programming module / odometer while working on a workbench. Pictures show INCORRECT power supply connection to DiagProg4 while programming module / odometer when working on a workbench. -
Page 16: Memory Card
4GB and up to 32GB. It is recommended to use only memory card provided by ElproSys or its authorized dealer. The use of different memory card may result in loss or damage of stored data. -
Page 17: Wifi Connection
DIAGPROG4 CONNECTION WITH PC (USB) In order to connect DiagProg4 to a PC ( configuration) cable with mini USB plug and maximum length of 1.5 m should be used. Once connected to a PC DiagProg4 is automatically detected by PC operating system. -
Page 18: Display Firmware Update
If the device screen does not respond to touch, it is possible to restart it to restore its efficiency. Press and hold buttons - up and - cancel for at least 3 seconds to restart DiagProg4 device. © ElproSys April, 2017 − Rev. 3.0... -
Page 19: Diagprog4 Manager
Software used to manage device using PC. DiagProg4 connection with PC: It is required to use mini USB cable supplied by manufacturer in order to connect DiagProg4 with PC. DiagProg4 should be connected to an additional power source. Software update Use this option to download latest update and activations from Elprosys server. -
Page 20: Diagprog4 Test
DIAGPROG4 TEST EXTERNAL INTERFACE TEST Diagprog4 user can use professional tester in order to test I/O lines. It can easily check its proper functioning. In order to do that please connect tester to system connector and also connect power supply. -
Page 21: Technical Data
3-axis accelerometer, light sensor EXTERNAL CONNECTORS: Mini-USB socket For configuration MicroSD card socket MicroSDHC™ 8GB card (up to 32GB) D-SUB25 connector used for connecting external devices. Maximum cable length is 1m. System connector © ElproSys April, 2017 − Rev. 3.0... -
Page 22: System Connector Features
SYSTEM CONNECTOR FEATURES Multifunctional system connector allows to connect with devices supported by the following interfaces. Only cables provided by ElproSys company or its official distributor should be used. ATTENTION The maximum length of the cable connected to the system connector is 1m. -
Page 23: Compliance With Standards
WiFi manufacturer certificate confirming compliance with electromagnetic compatibility standards. Certyfikat Producenta modułu WiFi potwierdzający spełnianie standardów kompatybilności STATEMENT CONCERNING PROHIBITED SUBSTANCES ElproSys would like to declare, that DiagProg4 device complies with the RoHS Directive recommendations. © ElproSys April, 2017 − Rev. 3.0... -
Page 24: Technical Support
Instruction manual DIAGNOSTIC TESTER TECHNICAL SUPPORT In case of any technical problems with DiagProg4 it is recommended to contact an authorised ElproSys representative or company directly. In order to solve any problems with the device, technical support can be accessed via www.diagprog4.com. -
Page 25: Warranty
User manual has been published by ElproSys company or its authorized dealer/representative. ElproSys reserves the right to make changes and amendments at any time to this instruction manual related to the improvement of the equipment. These changes will be included in subsequent editions of the instruction manual. -
Page 26: Certificates
Instruction manual DIAGNOSTIC TESTER CERTIFICATES DECLARATION OF CONFORMITY CE © ElproSys April, 2017 − Rev. 3.0... - Page 27 Instruction manual DIAGNOSTIC TESTER CERTIFICATE – SAFETY REGULAR PRODUCTION SURVEILLANCE © ElproSys April, 2017 − Rev. 3.0...
- Page 28 ..................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................© ElproSys April, 2017 − Rev. 3.0...
- Page 29 Czupryna Sylwester SENDING LOG FILE RESTART DIAGPROG4 Editing – Basic power supply parameters, implementation of 07.03.2016 Czupryna Sylwester the correct DiagProg4 power supply connection manual 08.03.2016 Czupryna Sylwester Change – Declaration of conformity CE 17.01.2017 Czupryna Sylwester Change – Declaration of conformity CE Change in TOOLS MENU –...
Need help?
Do you have a question about the DiagProg4 and is the answer not in the manual?
Questions and answers