Page 1 Durango SRT 2 0 1 8 O W N E R ’ S M A N U A L...
Page 2 VEHICLES SOLD IN CANADA This manual illustrates and describes the operation of With respect to any Vehicles Sold in Canada, the name features and equipment that are either standard or op- FCA US LLC shall be deemed to be deleted and the name tional on this vehicle.
Page 3 TABLE OF CONTENTS SECTION PAGE INTRODUCTION ..............3 GRAPHICAL TABLE OF CONTENTS .
Page 5: Table Of Contents
INTRODUCTION CONTENTS ▫ Symbols .......7 INTRODUCTION ......4 ROLLOVER WARNING .
Page 6: Introduction
4 INTRODUCTION INTRODUCTION This Owner’s Manual has been prepared with the assis- tance of service and engineering specialists to acquaint you Dear Customer, congratulations on selecting your new with the operation and maintenance of your vehicle. It is vehicle. Be assured that it represents precision workman- supplemented by Warranty Information, and customer ship, distinctive styling, and high quality.
Page 7: Rollover Warning
INTRODUCTION described for technical and/or commercial reasons. For Do not attempt sharp turns, abrupt maneuvers, or other further information, contact an authorized dealer. unsafe driving actions that can cause loss of vehicle con- trol. Failure to operate this vehicle safely may result in a If applicable, refer to the owners manual supplement for collision, rollover of the vehicle, and severe or fatal injury.
Page 8: How To Use This Manual
6 INTRODUCTION million annually. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Always buckle up. HOW TO USE THIS MANUAL Essential Information Consult the Table of Contents to determine which section contains the information you desire.
Page 9: Symbols
INTRODUCTION Symbols Consult the following table for a description of the symbols that may be used on your vehicle or throughout this Owner’s Manual:...
Page 10: Warnings And Cautions
8 INTRODUCTION WARNINGS AND CAUTIONS VEHICLE MODIFICATIONS/ALTERATIONS This Owner’s Manual contains WARNINGS against oper- WARNING! ating procedures that could result in a collision, bodily injury and/or death. It also contains CAUTIONS against Any modifications or alterations to this vehicle could procedures that could result in damage to your vehicle.
Page 11 GRAPHICAL TABLE OF CONTENTS CONTENTS FRONT VIEW ......10 INSTRUMENT PANEL .....12 REAR VIEW.
Page 12: Front View
10 GRAPHICAL TABLE OF CONTENTS FRONT VIEW Front View 1 — Doors 4 — Headlights 2 — Exterior Mirrors 5 — Windshield 3 — Wheels/Tires 6 — Hood/Engine Compartment...
Page 13: Rear View
GRAPHICAL TABLE OF CONTENTS 11 REAR VIEW Rear View 1 — Rear Lights 2 — Rear Windshield Wiper 3 — Liftgate...
Page 14: Instrument Panel
12 GRAPHICAL TABLE OF CONTENTS INSTRUMENT PANEL Instrument Panel 1 — Air Vents 4 — Instrument Cluster 2 — Paddle Shifter (–) 5 — Paddle Shifter (+) 3 — Steering Wheel 6 — Radio...
Page 15: Interior
GRAPHICAL TABLE OF CONTENTS 13 INTERIOR Interior 1 — Door Locks/Window Switches 4 — Climate Controls 2 — Seats 5 — Switch Panel 3 — Gear Selector 6 — Glove Compartment...
Page 17 GETTING TO KNOW YOUR VEHICLE CONTENTS ▫ General Information .....29 KEYS ....... . .19 ▫...
Page 18 16 GETTING TO KNOW YOUR VEHICLE ▫ Automatic Unlock On Exit Feature — ▫ Head Restraints — Rear Seats ....62 If Equipped ......40 ▫...
Page 19 GETTING TO KNOW YOUR VEHICLE 17 ▫ Daytime Running Lights — If Equipped ..72 ▫ Windshield Wiper Operation....80 ▫ Multifunction Lever ..... .72 ▫...
Page 20 18 GETTING TO KNOW YOUR VEHICLE ▫ Pinch Protect Feature ....107 ▫ Canadian/Gate Operator Programming ..117 ▫...
Page 21: Keys
GETTING TO KNOW YOUR VEHICLE 19 KEYS To remove the emergency key, slide the mechanical latch at the top of the key fob sideways with your thumb and then Key Fob pull the key out with your other hand. Your vehicle uses a keyless ignition system. The ignition system consists of a key fob with Remote Keyless Entry (RKE) and a START/STOP push button ignition system.
Page 22 20 GETTING TO KNOW YOUR VEHICLE To Unlock The Doors And Liftgate Push the interior door unlock button on the door panel. Push and release the unlock button on the key fob once to unlock the driver’s door or twice within five seconds to unlock all doors and the liftgate.
Page 23 GETTING TO KNOW YOUR VEHICLE 21 To Lock The Doors And Liftgate Replacing The Battery In The Key With Remote Control Push and release the lock button on the key fob to lock all doors and liftgate. The recommended replacement battery is one CR2032 battery.
Page 24: Getting To Know Your Vehicle 15
22 GETTING TO KNOW YOUR VEHICLE 1. Remove the emergency key by sliding the mechanical 2. Separate the key fob halves using the tip of the emer- latch on the back of the key fob sideways with your gency key, a #2 flat blade screwdriver, or a coin and thumb and pull the emergency key out with your other gently pry the two halves of the key fob apart.
Page 25 GETTING TO KNOW YOUR VEHICLE 23 Separating Case With A Coin Key Fob Battery Replacement 3. Remove the battery by turning the back cover over (battery facing downward) and tapping it lightly on a solid surface such as a table or similar and replace the battery.
Page 26: Ignition Switch
24 GETTING TO KNOW YOUR VEHICLE Programming Additional Key Fobs General Information Programming the key fob may be performed by an autho- The following regulatory statement applies to all radio rized dealer. frequency (RF) devices equipped in this vehicle: Request For Additional Remote Controls This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s).
Page 27: Ignition Or Accessory On Message
GETTING TO KNOW YOUR VEHICLE 25 Ignition Or Accessory On Message Upon opening the driver’s door when the ignition is in ACC or ON (engine not running), a chime will sound to remind you to place the ignition in the OFF mode. In addition to the chime, the ignition or accessory on message will display in the cluster.
Page 28: Dead Key Fob Battery
26 GETTING TO KNOW YOUR VEHICLE Dead Key Fob Battery WARNING! (Continued) Key Not Detected Feature • Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others If the ignition position does not change with a push of the could be seriously or fatally injured.
Page 29: Remote Start - If Equipped
GETTING TO KNOW YOUR VEHICLE 27 • Battery at an acceptable charge level REMOTE START — IF EQUIPPED • PANIC button not pushed How To Use Remote Start • System not disabled from previous remote start event This system uses the key fob to start the engine •...
Page 30: Remote Start Abort Message - If Equipped
28 GETTING TO KNOW YOUR VEHICLE Remote Start Abort Message — If Equipped NOTE: • If an engine fault is present or fuel level is low, the The following messages will display in the instrument vehicle will start and then shut down in 10 seconds. cluster display if the vehicle fails to remote start or exits remote start prematurely: •...
Page 31: To Exit Remote Start Mode And Drive The Vehicle
GETTING TO KNOW YOUR VEHICLE 29 To Exit Remote Start Mode And Drive The Vehicle General Information Before the end of 15-minute cycle, push and release the The following regulatory statement applies to all radio unlock button on the key fob to unlock the doors, or unlock frequency (RF) devices equipped in this vehicle: the vehicle using Keyless Enter-N-Go —...
Page 32: Customer Key Programming
30 GETTING TO KNOW YOUR VEHICLE the vehicle can be used to start and operate the vehicle. If All of the key fobs provided with your new vehicle have an invalid key fob is used to attempt to start and operate been programmed to the vehicle electronics.
Page 33: General Information
GETTING TO KNOW YOUR VEHICLE 31 When having the Sentry Key Immobilizer System serviced, vehicle security alarm will provide the following audible bring all vehicle keys with you to an authorized dealer. and visible signals: the horn will pulse, the park lamps and/or turn signals will flash, and the vehicle security light General Information in the instrument cluster will flash.
Page 34: To Disarm The System
32 GETTING TO KNOW YOUR VEHICLE NOTE: Security System Manual Override NOTE: • The driver’s door key cylinder and the liftgate button on the The vehicle security alarm will not arm if you lock the key fob cannot arm or disarm the vehicle security alarm. doors using the manual door lock plunger.
Page 35: Rearming Of The System
GETTING TO KNOW YOUR VEHICLE 33 Rearming Of The System If something triggers the alarm, and no action is taken to disarm it, the vehicle security alarm will turn the horn off after 29 seconds, five seconds between cycles, up to eight cycles if the trigger remains active and the vehicle security alarm will rearm itself.
Page 36: Power Door Locks
34 GETTING TO KNOW YOUR VEHICLE WARNING! (Continued) brake pedal or the gear selector. • Do not leave the key fob in or near the vehicle, or in a location accessible to children, and do not leave the ignition of a vehicle equipped with Keyless Enter- N-Go in the ACC or ON/RUN mode.
Page 37: Keyless Enter-N-Go - Passive Entry
GETTING TO KNOW YOUR VEHICLE 35 • If the vehicle is unlocked by Passive Entry and no door If a rear door is locked, it cannot be opened from inside the vehicle without first unlocking the door. The door may be is opened within 60 seconds, the vehicle will re-lock and unlocked manually by raising the lock knob.
Page 38 36 GETTING TO KNOW YOUR VEHICLE To Unlock From The Driver’s Side: To Unlock From The Passenger Side: With a valid Passive Entry key fob within 5 ft (1.5 m) of the With a valid Passive Entry key fob within 5 ft (1.5 m) of the driver’s door handle, grab the driver’s front door handle to passenger door handle, grab the front passenger door unlock the driver’s door automatically.
Page 39 GETTING TO KNOW YOUR VEHICLE 37 three times (on the third attempt, ALL doors will lock, and the Passive Entry key fob can be locked in the vehicle). To Unlock/Enter The Liftgate The liftgate passive entry unlock feature is built into the electronic liftgate handle.
Page 40 38 GETTING TO KNOW YOUR VEHICLE To Lock The Liftgate With a valid Passive Entry key fob within 5 ft (1.5 m) of the liftgate, push the passive entry lock button located to the right of electronic liftgate handle. NOTE: If “Unlock All Doors 1st Press” is programmed in Uconnect Settings, all doors will unlock when you push the button on the liftgate.
Page 41 GETTING TO KNOW YOUR VEHICLE 39 NOTE: Do NOT grab the door handle, when pushing the NOTE: door handle button. This could unlock the door(s). • After pushing the door handle button, you must wait two seconds before you can lock or unlock the doors, using either Passive Entry door handle or door handle button.
Page 42: Automatic Unlock On Exit Feature - If Equipped
40 GETTING TO KNOW YOUR VEHICLE General Information Automatic Unlock On Exit Feature — If Equipped The following regulatory statement applies to all radio If Auto Unlock is enabled, this feature will unlock all the frequency (RF) devices equipped in this vehicle: doors when any door is opened if the vehicle is stopped and in PARK.
Page 43 GETTING TO KNOW YOUR VEHICLE 41 To Engage Or Disengage The Child Protection Door Lock System 1. Open the rear door. 2. Insert the tip of the emergency key into the lock and rotate to the lock or unlock position. 3.
Page 44: Seats
42 GETTING TO KNOW YOUR VEHICLE SEATS Power Adjustment (Front Seats) Seats are a part of the Occupant Restraint System of the Some models may be equipped with eight-way power vehicle. driver and front passenger seats. The power seat switches are located on the outboard side of the seat.
Page 45 GETTING TO KNOW YOUR VEHICLE 43 Adjusting The Seat Forward Or Rearward WARNING! The seat can be adjusted both forward and rearward. Push • Adjusting a seat while driving may be dangerous. the seat switch forward or rearward. The seat will move in Moving a seat while driving could result in loss of the direction of the switch.
Page 46: Power Passenger Seat Adjustment - If Equipped
44 GETTING TO KNOW YOUR VEHICLE Power Lumbar — If Equipped Power Passenger Seat Adjustment — If Equipped Vehicles equipped with power driver or passenger seats Some models are equipped with a six-way power passen- may also be equipped with power lumbar. The power ger seat.
Page 47: Driver Memory Seat - If Equipped
GETTING TO KNOW YOUR VEHICLE 45 Reclining The Seatback CAUTION! The angle of the seatback can be adjusted forward or Do not place any article under a power seat or impede rearward. Push the seatback switch forward or rearward, its ability to move as it may cause damage to the seat the seat will move in the direction of the switch.
Page 48 46 GETTING TO KNOW YOUR VEHICLE The memory seat switch is located on the driver’s door Programming The Memory Feature trim panel. The switch consists of three buttons: NOTE: To create a new memory profile, perform the • The set (S) button, which is used to activate the memory following: save function.
Page 49 GETTING TO KNOW YOUR VEHICLE 47 Linking And Unlinking The Remote Keyless Entry 5. Push and release the lock button on the key fob within Key Fob To Memory 10 seconds. Your key fobs can be programmed to recall one of two NOTE: Your key fobs can be unlinked to your memory pre-programmed memory profiles by pushing the unlock settings by pushing the set (S) button, and within 10...
Page 50 48 GETTING TO KNOW YOUR VEHICLE • When you cycle the vehicle’s ignition to the OFF posi- Driver Two Memory Position Recall tion, the driver seat will move about 2.4 inches (60 mm) • To recall the memory setting for driver two using the rearward if the driver seat position is greater than or memory switch, push memory button (2) on the equal to 2.7 inches (67.7 mm) forward of the rear stop.
Page 51: Heated Seats - If Equipped
GETTING TO KNOW YOUR VEHICLE 49 Heated Seats — If Equipped You can choose from HI, LO, or OFF heat settings. The indicator arrows in touchscreen buttons indicate the level On some models, the front and rear seats may be equipped of heat in use.
Page 52 50 GETTING TO KNOW YOUR VEHICLE Vehicles Equipped With Remote Start Rear Heated Seats — If Equipped On some models, the two rear outboard seats may be On models that are equipped with remote start, the heated equipped with heated seats. There are two heated seat seats can be programmed to come on during a remote start.
Page 53: Front Ventilated Seats - If Equipped
GETTING TO KNOW YOUR VEHICLE 51 You can choose from HI, LO, or OFF heat settings. Amber WARNING! indicator lights in each switch indicate the level of heat in • Persons who are unable to feel pain to the skin use.
Page 54: 60/40 Split Rear Seat
52 GETTING TO KNOW YOUR VEHICLE The front ventilated seats control buttons are located 60/40 Split Rear Seat within the Uconnect system. You can gain access to the Second Row Fold Flat Seat control buttons through the climate screen or the controls The second row seats can be folded flat to carry cargo.
Page 55 GETTING TO KNOW YOUR VEHICLE 53 Easy Access For Third Row Either side of the rear seat can be tumbled forward to allow passengers to easily access the third row seats. 1. Pull upward on the release lever to release the seat. Fold-Flat Second Row Seat NOTE: You may experience deformation in the seat cush- ion from the seat belt buckles if the seats are left folded for...
Page 56 54 GETTING TO KNOW YOUR VEHICLE 2. Tumble the seat forward using the pull strap located behind the seatback. Tumbled Second Row WARNING! Tumble Strap Do not drive the vehicle with the second row seats in the tumbled position. The second row seats are only intended to be tumbled for entry and exit to the third row seat.
Page 57: Rear Captain's Chairs - If Equipped
GETTING TO KNOW YOUR VEHICLE 55 To Raise Rear Seat Pull upward on the release lever located on the outboard side of the seat. Fold the seat rearward to it’s original position, and lock it into place. WARNING! Be certain that the seatback is securely locked into position.
Page 58 56 GETTING TO KNOW YOUR VEHICLE Easy Access For Third Row Either side of the rear seat can be tumbled forward to allow passengers to easily access the third row seats. 1. Pull upward on the release lever to release the seat. Fold-Flat Second Row Seats NOTE: You may experience deformation in the seat cush- ion from the seat belt buckles if the seats are left folded for...
Page 59 GETTING TO KNOW YOUR VEHICLE 57 2. Tumble the seat forward using the pull strap located 3. If your vehicle is equipped with a mini console, there is behind the seatback. a stepping pad to allow passengers to easily access the third row seats.
Page 60: Folding Third Row
58 GETTING TO KNOW YOUR VEHICLE To Raise Rear Seat Folding Third Row Fold the seat rearward to it’s original position, and lock it Both third row seats can be folded forward to increase the into place. cargo area. To lower either seat, pull on the release handle located on back of the seat and lower the seat using the pull WARNING! strap located next to the release handle.
Page 61: Head Restraints
GETTING TO KNOW YOUR VEHICLE 59 WARNING! Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury.
Page 62: Supplemental Active Head Restraints - Front Seats
60 GETTING TO KNOW YOUR VEHICLE Supplemental Active Head Restraints — Front Seats Active Head Restraints are passive, deployable compo- nents, and vehicles with this equipment cannot be readily identified by any markings, only through visual inspection of the head restraint. The Active Head Restraints (AHR) will be split in two halves, with the front half being soft foam and trim, the back half being decorative plastic.
Page 63 GETTING TO KNOW YOUR VEHICLE 61 Active Head Restraint (Normal Position) Active Head Restraint (Tilted) NOTE: • The head restraints should only be removed by qualified technicians, for service purposes only. If either of the head restraints require removal, see your authorized dealer.
Page 64: Head Restraints - Rear Seats
62 GETTING TO KNOW YOUR VEHICLE Head Restraints — Rear Seats WARNING! The head restraints on the outboard seats are not adjust- • All occupants, including the driver, should not oper- able. They automatically fold forward when the rear seat is ate a vehicle or sit in a vehicle’s seat until the head folded to a load floor position, but do not return to their restraints are placed in their proper positions in...
Page 65: Head Restraint Removal - Rear Seats
GETTING TO KNOW YOUR VEHICLE 63 WARNING! WARNING! • ALL the head restraints MUST be reinstalled in the Sitting in a seat with the head restraint in its lowered position could result in serious injury or death in a vehicle to properly protect the occupants. Follow the collision.
Page 66: Power Folding Third Row Head Restraints
64 GETTING TO KNOW YOUR VEHICLE NOTE: For proper routing of a Child Seat Tether, refer to Power Folding Third Row Head Restraints “Occupant Restraints” in “Safety” for further information. For improved visibility when in reverse, the third row head restraints can be folded using the Uconnect System.
Page 67: Steering Wheel
GETTING TO KNOW YOUR VEHICLE 65 STEERING WHEEL To tilt the steering column, move the lever up or down as desired. To lengthen or shorten the steering column, pull Power Tilt/Telescoping Steering Column the lever toward you or push the lever away from you as This feature allows you to tilt the steering column upward desired.
Page 68: Heated Steering Wheel - If Equipped
66 GETTING TO KNOW YOUR VEHICLE Heated Steering Wheel — If Equipped Vehicles Equipped With Remote Start The steering wheel contains a heating element that helps On models that are equipped with remote start, the heated warm your hands in cold weather. The heated steering steering wheel can be programmed to come on during a wheel has only one temperature setting.
Page 69: Mirrors
GETTING TO KNOW YOUR VEHICLE 67 MIRRORS Automatic Dimming Mirror The mirror head can be adjusted up, down, left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window. This mirror automatically adjusts for headlight glare from vehicles behind you.
Page 70: Outside Mirrors
68 GETTING TO KNOW YOUR VEHICLE Outside Mirrors Outside Automatic Dimming Mirrors — If Equipped To receive maximum benefit, adjust the outside mirror(s) to The outside mirrors will automatically adjust for glare center on the adjacent lane of traffic with a slight overlap of from vehicles behind you.
Page 71: Heated Mirrors - If Equipped
GETTING TO KNOW YOUR VEHICLE 69 Heated Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature will be activated whenever you turn on the rear window defroster (if equipped). Refer to “Climate Controls” in “Getting To Know Your Vehicle” for further information.
Page 72: Illuminated Vanity Mirrors
70 GETTING TO KNOW YOUR VEHICLE Illuminated Vanity Mirrors Sun Visor “Slide-On-Rod” Feature — If Equipped To access an illuminated vanity mirror, flip down one of the The sun visor “Slide-On-Rod” feature allows for additional visors. flexibility in positioning the sun visor to block out the sun. Lift the cover to reveal the mirror.
Page 73: Exterior Lights
GETTING TO KNOW YOUR VEHICLE 71 EXTERIOR LIGHTS To turn on the headlights, rotate the headlight switch clockwise. When the headlight switch is Headlight Switch on, the parking lights, taillights, license plate The headlight switch is located on the left side of the light and instrument panel lights are also turned instrument panel, next to the steering wheel.
Page 74: Daytime Running Lights - If Equipped
72 GETTING TO KNOW YOUR VEHICLE Daytime Running Lights — If Equipped Multifunction Lever The Daytime Running Lights come on whenever the en- The multifunction lever is located on the left side of the gine is running, and the transmission is not in the PARK steering column.
Page 75: Automatic High Beam - If Equipped
GETTING TO KNOW YOUR VEHICLE 73 Automatic High Beam — If Equipped Flash-To-Pass The Automatic High Beam Headlamp Control system You can signal another vehicle with your headlights by provides increased forward lighting at night by automat- lightly pulling the multifunction lever toward you. This ing high beam control through the use of a digital camera will cause the high beam headlights to turn on, and remain mounted on the inside rearview mirror.
Page 76: Parking Lights And Panel Lights
74 GETTING TO KNOW YOUR VEHICLE Parking Lights And Panel Lights Headlight Delay To aid in your exit, your vehicle is equipped with a To turn on the parking lights and instrument panel headlight delay that will leave the headlights on for lights, rotate the headlight switch clockwise.
Page 77: Fog Lights - If Equipped
GETTING TO KNOW YOUR VEHICLE 75 Fog Lights — If Equipped Turn Signals The fog lights are turned on by rotating the headlight Move the multifunction lever up or down and the arrows switch to the parking light or headlight position and on each side of the instrument cluster will flash to show pushing in the headlight rotary control.
Page 78: Battery Saver
76 GETTING TO KNOW YOUR VEHICLE Battery Saver INTERIOR LIGHTS To protect the life of your vehicle’s battery, load shedding Courtesy Lights is provided for both the interior and exterior lights. The courtesy lights can be turned on by pushing the top If the ignition is OFF and any door is left ajar for 10 minutes corner of the lens.
Page 79 GETTING TO KNOW YOUR VEHICLE 77 Front Map/Reading Lights — If Equipped To turn the lights off, push the switch a second time. The lights also turn on when a door is opened. The lights will Lights are mounted in the overhead console. Each light can also turn on when the unlock button on the key fob is be turned on by pushing the switch on either side of the pushed.
Page 80 78 GETTING TO KNOW YOUR VEHICLE Ambient Light — If Equipped Dimmer Control The overhead console is equipped with an ambient light Courtesy and dome lights are turned on when the front feature. This light casts illumination for improved visibility doors are opened or when the dimmer control (rotating of the floor and center console area.
Page 81: Windshield Wipers And Washers
GETTING TO KNOW YOUR VEHICLE 79 The brightness of the instrument panel lighting can be WINDSHIELD WIPERS AND WASHERS regulated by rotating the dimmer control up (brighter) or The windshield wiper/washer controls are located on the down (dimmer). When the headlights are on you can multifunction lever on the left side of the steering column.
Page 82: Windshield Wiper Operation
80 GETTING TO KNOW YOUR VEHICLE Windshield Wiper Operation CAUTION! Rotate the end of the lever to one of the first four detent Always remove any buildup of snow that prevents the positions for intermittent settings, the fifth detent for low windshield wiper blades from returning to the “park”...
Page 83 GETTING TO KNOW YOUR VEHICLE 81 Intermittent Wiper System Windshield Washer Operation Use one of the four intermittent wiper settings when To use the washer, push on the end of the lever (toward the weather conditions make a single wiping cycle, with a steering wheel) and hold while spray is desired.
Page 84: Rain Sensing Wipers - If Equipped
82 GETTING TO KNOW YOUR VEHICLE from the windshield washers of the vehicle ahead. Rotate WARNING! the end of the multifunction lever to one of four settings to activate this feature. Sudden loss of visibility through the windshield could lead to a collision. You might not see other vehicles or The sensitivity of the system can be adjusted with the other obstacles.
Page 85: Rear Window Wiper/Washer
GETTING TO KNOW YOUR VEHICLE 83 The Rain Sensing system has protection features for the Rear Window Wiper/Washer wiper blades and arms, and will not operate under the The rear wiper/washer controls are located on the multi- following conditions: function lever on the left side of the steering column. The •...
Page 86: Climate Controls
84 GETTING TO KNOW YOUR VEHICLE CLIMATE CONTROLS Rotate the center portion of the lever upward to the first detent for intermittent operation and to the The Climate Control System allows you to regulate the second detent for continuous rear wiper operation. temperature, air flow, and direction of air circulating throughout the vehicle.
Page 87: Automatic Climate Control Overview
GETTING TO KNOW YOUR VEHICLE 85 Automatic Climate Control Overview Uconnect 4C/4C With 8.4–inch Display NAV Temperature Controls...
Page 88 86 GETTING TO KNOW YOUR VEHICLE Control Descriptions Icon Description MAX A/C Button Press and release to change the current setting, the indicator illuminates when MAX A/C is ON. Performing this function again will cause the MAX A/C operation to switch into manual mode and the MAX A/C indicator will turn off.
Page 89 GETTING TO KNOW YOUR VEHICLE 87 Icon Description Front Defrost Button Press and release to change the current airflow setting to Defrost mode. The indicator illumi- nates when this feature is ON. Air comes from the windshield and side window demist outlets. When the defrost button is selected, the blower level may increase.
Page 90 88 GETTING TO KNOW YOUR VEHICLE Icon Description SYNC Button Press the Sync button on the touchscreen to toggle the Sync feature On/Off. The Sync indicator is illuminated when this feature is enabled. Sync is used to synchronize the passenger tempera- ture setting with the driver temperature setting.
Page 91 GETTING TO KNOW YOUR VEHICLE 89 Icon Description Bi-Level Mode Bi-Level Mode Air comes from the instrument panel outlets and floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. NOTE: Bi-Level mode is designed under comfort conditions to provide cooler air out of the panel out- lets and warmer air from the floor outlets.
Page 92 90 GETTING TO KNOW YOUR VEHICLE Controlling The Rear Climate Controls From The CAUTION! Front ATC Panel Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear win- dow.
Page 93 GETTING TO KNOW YOUR VEHICLE 91 The Three-Zone ATC system allows for adjustment of the rear climate controls from the front ATC panel. To change the rear system settings: • Press the REAR CLIMATE button on the touchscreen to change control to rear control mode, Rear display (below) appears.
Page 94 92 GETTING TO KNOW YOUR VEHICLE Icon Description Floor Mode Floor Mode Air comes from the floor outlets. Rear Temperature Display This display shows the temperature setting for the rear seat occupants. Blower Control Display This display shows the current Blower speed selection. Rear Auto Indicator This indicates when the system is in Rear Auto mode.
Page 95 GETTING TO KNOW YOUR VEHICLE 93 Icon Description SYNC Button Press the Sync button on the touchscreen to toggle the Sync feature On/Off. The Sync indicator is illuminated when this feature is enabled. Sync is used to synchronize the passenger temperature setting with the driver temperature setting.
Page 96 94 GETTING TO KNOW YOUR VEHICLE Rear Automatic Temperature Control The rear ATC system has floor air outlets at the rear right side of the 3rd Row seats and overhead outlets at each outboard rear seating position. The system provides heated air through the floor outlets or cool, dehumidified air through the headliner outlets.
Page 97 GETTING TO KNOW YOUR VEHICLE 95 Icon Description Bi-Level Mode Bi-Level Mode Air comes from both the headliner outlets and the floor outlets. NOTE: In many temperature positions, the Bi-Level mode is designed to provide cooler air out of the headliner outlets and warmer air from the floor outlets. Floor Mode Floor Mode Air comes from the floor outlets.
Page 98: Climate Control Functions
96 GETTING TO KNOW YOUR VEHICLE • Rotate the Rear Blower, Rear Temperature and the Rear CAUTION! Mode Control knobs to suit your comfort needs. Interior air enters the Rear Automatic Temperature • ATC is selected by adjusting the rear blower knob Control System through an intake grille, located in counterclockwise to AUTO.
Page 99: Automatic Temperature Control (Atc)
GETTING TO KNOW YOUR VEHICLE 97 NOTE: Recirculation • For Manual Climate Controls, if the system is in Mix, When outside air contains smoke, odors, or high humidity, Floor or Defrost Mode, the A/C can be turned off, but or if rapid cooling is desired, you may wish to recirculate the A/C system shall remain active to prevent fogging of interior air by pressing the recirculation control button.
Page 100 98 GETTING TO KNOW YOUR VEHICLE temperatures. Once the desired temperature is dis- NOTE: The system will not automatically sense the pres- played, the system will achieve and automatically main- ence of fog, mist or ice on the windshield. DEFROST mode tain that comfort level.
Page 101: Operating Tips
GETTING TO KNOW YOUR VEHICLE 99 Rear Temperature Control Winter Operation To change the temperature in the rear of the vehicle, push Use of the Air Recirculation mode during winter months is the temperature buttons. The rear temperature settings are not recommended because it may cause window fogging.
Page 102 100 GETTING TO KNOW YOUR VEHICLE NOTE: Outside Air Intake • Recirculate without A/C should not be used for long Make sure the air intake, located directly in front of the periods, as fogging may occur. windshield, is free of obstructions, such as leaves. Leaves collected in the air intake may reduce airflow, and if they •...
Page 103 GETTING TO KNOW YOUR VEHICLE 101 Control Setting Suggestions For Various Weather Conditions...
Page 104: Windows
102 GETTING TO KNOW YOUR VEHICLE WINDOWS The power window switches remain active for up to 10 minutes after the ignition has been turned OFF. Opening a Power Windows vehicle front door will cancel this feature. The power window controls are located on the driver’s door trim panel.
Page 105 GETTING TO KNOW YOUR VEHICLE 103 NOTE: If the window runs into any obstacle during Auto-Up, it will reverse direction and then go back down. Remove the obstacle and use the window switch again to close the window. Any impact due to rough road condi- tions may trigger the auto reverse function unexpectedly during Auto-Up.
Page 106: Wind Buffeting
104 GETTING TO KNOW YOUR VEHICLE Window Lockout Switch Wind Buffeting The window lockout switch on the driver’s door trim panel Wind buffeting can be described as the perception of allows you to disable the window controls on the rear pressure on the ears or a helicopter-type sound in the ears.
Page 107: Power Sunroof - If Equipped
GETTING TO KNOW YOUR VEHICLE 105 POWER SUNROOF — IF EQUIPPED WARNING! The power sunroof switch is located between the sun • Never leave children unattended in a vehicle, or with visors on the overhead console. access to an unlocked vehicle. Never leave the key fob in or near the vehicle, or in a location accessible to children.
Page 108: Opening Sunroof
106 GETTING TO KNOW YOUR VEHICLE Opening Sunroof position. The sunroof will close fully and stop automati- cally. This is called “Express Close.” During Express Close Express operation, any other actuation of the switch will stop the Push the switch rearward and release it within one-half sunroof.
Page 109: Sunshade Operation
GETTING TO KNOW YOUR VEHICLE 107 Sunshade Operation Sunroof Maintenance The sunshade can be opened manually. However, the Use only a non-abrasive cleaner and a soft cloth to clean the sunshade will open automatically as the sunroof opens. glass panel. NOTE: The sunshade cannot be closed if the sunroof is Ignition Off Operation open.
Page 110: Hood
108 GETTING TO KNOW YOUR VEHICLE 3. Push and hold the close switch. The sunroof will hit the HOOD hard stop and move to the vent position after ten Opening The Hood seconds. To open the hood, two latches must be released. 4.
Page 111: Closing The Hood
GETTING TO KNOW YOUR VEHICLE 109 2. Reach under the hood from outside the vehicle, move CAUTION! the safety latch to the left and lift the hood. To prevent possible damage, do not slam the hood to close it. Lower hood to approximately 12 inches (30 cm) and drop the hood to close.
Page 112 110 GETTING TO KNOW YOUR VEHICLE trim panel, near the liftgate opening. If the liftgate is in WARNING! motion, pushing the liftgate button located on left rear trim panel will reverse the liftgate. During power operation, personal injury or cargo damage may occur.
Page 113: Cargo Area Features
GETTING TO KNOW YOUR VEHICLE 111 • If the electronic liftgate release is pushed while the Cargo Area Features power liftgate is closing, the liftgate will reverse to the Cargo Storage full open position. There is a removable storage bin located on the left side of •...
Page 114 112 GETTING TO KNOW YOUR VEHICLE Retractable Cargo Area Cover — If Equipped Cargo Tie-Down Hooks The cargo tie-downs, located on the cargo area floor, NOTE: The purpose of this cover is for privacy, not to should be used to safely secure loads when the vehicle is secure loads.
Page 115 GETTING TO KNOW YOUR VEHICLE 113 WARNING! WARNING! (Continued) injury, follow these guidelines for loading your ve- • Cargo tie-downs are not safe anchors for a child seat hicle: tether strap. In a sudden stop or accident, a tie-down • Do not carry loads that exceed the load limits de- could pull loose and allow the child seat to come scribed on the label attached to the left door or left loose.
Page 116: Garage Door Opener - If Equipped
114 GETTING TO KNOW YOUR VEHICLE GARAGE DOOR OPENER — IF EQUIPPED HomeLink replaces up to three remote controls (handheld transmitters) that operate devices such as garage door openers, motorized gates, lighting or home security sys- tems. The HomeLink unit operates off your vehicle’s battery.
Page 117: Programming A Rolling Code
GETTING TO KNOW YOUR VEHICLE 115 To erase the channels, place the ignition in the ON/RUN position and push and hold the two outside HomeLink buttons (I and III) for up 20 seconds or until the red indicator flashes. NOTE: •...
Page 118: Programming A Non-Rolling Code
116 GETTING TO KNOW YOUR VEHICLE 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) 6. Return to the vehicle and push the programmed away from the HomeLink button you wish to program HomeLink button twice (holding the button for two while keeping the HomeLink indicator light in view.
Page 119: Canadian/Gate Operator Programming
GETTING TO KNOW YOUR VEHICLE 117 3. Push and hold the Homelink button you want to the signal during programming. Similar to this Canadian program while you push and hold the hand-held trans- law, some U.S. gate operators are designed to time-out in mitter button.
Page 120: Using Homelink
118 GETTING TO KNOW YOUR VEHICLE seconds or longer in rare cases. The garage door may HomeLink will remain active for three minutes. During open and close while you are programming. this time, if the vehicle is locked, HomeLink is disabled. 5.
Page 121: General Information
GETTING TO KNOW YOUR VEHICLE 119 If you have any problems, or require assistance, please call General Information toll-free 1-800-355-3515 Internet The following regulatory statement applies to all Radio HomeLink.com for information or assistance. Frequency (RF) devices equipped in this vehicle: This device complies with Part 15 of the FCC Rules and WARNING! with Industry Canada license-exempt RSS standard(s).
Page 122: Internal Equipment
120 GETTING TO KNOW YOUR VEHICLE INTERNAL EQUIPMENT Door Storage Large storage areas are built into the door panels for easy Storage access. Glove Compartment The glove compartment is located on the passenger side of the instrument panel. Door Panel Storage Glove Compartment To open the glove compartment, pull the release handle.
Page 123 GETTING TO KNOW YOUR VEHICLE 121 Front Center Console Rear Full Center Console — If Equipped The front center console contains both an upper and a The rear full center console contains both an upper and a lower storage area. lower storage area.
Page 124 122 GETTING TO KNOW YOUR VEHICLE To open the upper storage compartment, pull upward on NOTE: Lower storage compartment light is always on with the small latch located on the front of the lid. ignition in the ON/RUN position. Upper Storage Compartment Lower Storage Compartment Lift upward on the larger of the latches to access the lower storage compartment.
Page 125 GETTING TO KNOW YOUR VEHICLE 123 When lifted forward there is access to the lower storage CAUTION! compartment. Remove any items stored in the console cupholders or devices with cords routing through upper storage area. Damage may occur to upper console lid and device cables when upper storage compartment is lifted for- ward.
Page 126 124 GETTING TO KNOW YOUR VEHICLE NOTE: When the lower storage compartment is accessed, Open storage areas, or cubby bins with removable liners, it allows the armrest to flip forward for “fold flat mode”. are located rearward of the cupholders and in the lower Fold flat mode allows the console armrest to be lowered front of the console.
Page 127: Cupholders
GETTING TO KNOW YOUR VEHICLE 125 Rear Mini Center Console — If Equipped Cupholders An open storage area, or cubby bin with removable liner, is Front Seat Cupholders located in the front of the console. There are two cupholders for the front seat passengers located in the center console.
Page 128 126 GETTING TO KNOW YOUR VEHICLE Rear Cupholders Rear Full Console Cupholders — If Equipped Rear Center Arm Rest Cupholders — If Equipped There are two cupholders for the rear seat passengers located in the front of the rear full console. There are two cupholders for the rear seat passengers located in the fold-down center armrest.
Page 129 GETTING TO KNOW YOUR VEHICLE 127 The rear full console cupholders are equipped with a light Rear Mini Console Cupholders — If Equipped ring that illuminates the cupholders for the rear passen- There are two cupholders for the rear seat passengers gers.
Page 130: Electrical Power Outlets
128 GETTING TO KNOW YOUR VEHICLE • Power outlets are designed for accessory plugs only. Do Electrical Power Outlets not insert any other object in the power outlets as this Your vehicle is equipped with 12 Volt (13 Amp) power will damage the outlet and blow the fuse.
Page 131 GETTING TO KNOW YOUR VEHICLE 129 In addition to the front power outlet, there is also a power If your vehicle is equipped with a rear full center console, outlet located in the storage area of the center console. there is also a power outlet located in the lower storage area of the rear full center console.
Page 132 130 GETTING TO KNOW YOUR VEHICLE The rear cargo power outlet is located in the right rear NOTE: The rear cargo power outlet can be changed to cargo area. “battery” powered all the time by switching the power outlet right rear quarter panel fuse in the fuse panel from fuse location F90 to F91.
Page 133 GETTING TO KNOW YOUR VEHICLE 131 WARNING! (Continued) • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure. CAUTION! • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.).
Page 134: Power Inverter - If Equipped
132 GETTING TO KNOW YOUR VEHICLE Power Inverter — If Equipped The power inverter is designed with built-in overload protection. If the power rating of 150 Watts is exceeded, the There is a 115 Volt, 150 Watt inverter outlet located on the power inverter automatically shuts down.
Page 135: Sunglasses Bin Door
GETTING TO KNOW YOUR VEHICLE 133 Sunglasses Bin Door ROOF LUGGAGE RACK — IF EQUIPPED At the front of the console a compartment is provided for The crossbars and side rails are designed to carry weight the storage of a pair of sunglasses. The storage compart- on vehicles equipped with a luggage rack.
Page 136: Deploying The Crossbars
134 GETTING TO KNOW YOUR VEHICLE The roof rack does not increase the total load carrying 2. Remove the crossbar from the stowed position by slid- capacity of the vehicle. Be sure the total load of cargo inside ing the crossbar towards the center of the roof. Repeat the vehicle plus that on the external rack does not exceed with crossbar on the opposite side.
Page 137 GETTING TO KNOW YOUR VEHICLE 135 3. Starting with one crossbar, bend down the pivot sup- 4. Position the crossbars across the roof making sure the ports at each end. letters on the crossbars align with the matching letters on the side rail. Bending Pivot Positioning Crossbars...
Page 138: Stowing The Crossbars
136 GETTING TO KNOW YOUR VEHICLE 5. Slide the cross bar into to the deploy position by moving 6. Deploy and tighten the second crossbar to complete the it towards the matching letter in the side rail. Be sure the deployment of the crossbars.
Page 139 GETTING TO KNOW YOUR VEHICLE 137 3. Position the crossbar along the correct side rail. Make CAUTION! sure the letters on the crossbar align with the matching letters on the side rail. Use care when removing and handling the crossbars to prevent damage to the vehicle.
Page 140 138 GETTING TO KNOW YOUR VEHICLE 4. Slide the crossbar outward, away from the center of the 5. Once the driver’s side crossbar is in place, tighten the roof. The crossbar will nest fully within the side rail. thumb screws completely. Crossbar To Side Rail Tightening Crossbar...
Page 141 GETTING TO KNOW YOUR VEHICLE 139 6. Repeat the procedure to stow the second crossbar on the WARNING! opposite side. Cargo must be securely tied down before driving your vehicle. Improperly secured loads can fly off the ve- hicle, particularly at high speeds, resulting in personal injury or property damage.
Page 142 140 GETTING TO KNOW YOUR VEHICLE CAUTION! (Continued) points if needed. Tie loops are intended as supple- mentary tie down points only. Do not use ratcheting mechanisms with the tie loops. Check the straps and thumb wheels frequently to be sure that the load remains securely attached.
Page 143 GETTING TO KNOW YOUR INSTRUMENT PANEL CONTENTS INSTRUMENT CLUSTER ....142 WARNING LIGHTS AND MESSAGES ..156 ▫...
Page 144: Instrument Cluster
142 GETTING TO KNOW YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER Instrument Cluster 2. Tachometer Instrument Cluster Descriptions • Indicates the engine speed in revolutions per minute 1. Speedometer (RPM x 1000). • Indicates vehicle speed. 3. Temperature Gauge...
Page 145 GETTING TO KNOW YOUR INSTRUMENT PANEL 143 • The temperature gauge shows engine coolant tem- CAUTION! perature. Any reading within the normal range indi- cates that the engine cooling system is operating Driving with a hot engine cooling system could dam- satisfactorily.
Page 146: Instrument Cluster Display
144 GETTING TO KNOW YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DISPLAY The system allows the driver to select information by pushing the following buttons mounted on the steering Location And Controls wheel: The Main Menu items consists of the following: • Speedometer Main Gauge •...
Page 147 GETTING TO KNOW YOUR INSTRUMENT PANEL 145 • Down Arrow Button The instrument cluster display is located in the center portion of the cluster and consist of multiple sections: Push and release the down arrow button to scroll • Main Screen — The inner ring of the display will downward through the main menu.
Page 148: Engine Oil Life Reset
146 GETTING TO KNOW YOUR INSTRUMENT PANEL • Five Second Unstored Messages These pop up messages fall into several categories: • Five Second Stored Messages When the appropriate conditions occur, this type of mes- sage takes control of the main display area for five seconds When the appropriate conditions occur, this type of mes- and then returns to the previous screen.
Page 149: Display And Messages
GETTING TO KNOW YOUR INSTRUMENT PANEL 147 Vehicles Equipped With Keyless Enter-N-Go — Ignition Secondary Method Of Resetting Engine Oil Life Use the steering wheel instrument cluster display controls 1. Without pressing the brake pedal, push the ENGINE for the following procedure(s): START/STOP button and place the ignition to the ON/RUN position (do not start the engine).
Page 150 148 GETTING TO KNOW YOUR INSTRUMENT PANEL • Oil Change Due • Left Rear Turn Signal Light Out • Fuel Low • Ignition or Accessory On • Service Anti-lock Brake System • Vehicle Not In Park • Service Electronic Throttle Control •...
Page 151: Instrument Cluster Display Selectable Menu Items
GETTING TO KNOW YOUR INSTRUMENT PANEL 149 • Vehicle Speed Too High To Shift to D Vehicle Info • Vehicle Speed is Too High to Shift to R Push and release the up or down arrow button until the Vehicle Info icon/title is highlighted in the instrument •...
Page 152 150 GETTING TO KNOW YOUR INSTRUMENT PANEL Transmission Temperature Engine Power • Displays the actual transmission temperature. • Displays the current engine power. Oil Temperature Performance Features • Displays the actual oil temperature. Push and release the up or down arrow button until the SRT icon/title is highlighted in the instrument cluster Oil Pressure display.
Page 153 GETTING TO KNOW YOUR INSTRUMENT PANEL 151 • 1/4 Mile (400 meters) Timer The Performance Features include the following: • 0-60 MPH (0-100 km/h) Timer – Best – Last – Best – Recent – Last – Reaction Time — If Selected –...
Page 154 152 GETTING TO KNOW YOUR INSTRUMENT PANEL Fuel Economy Audio Push and release the up or down arrow button until the Push and release the up or down arrow button until the Fuel Economy Menu icon/title is highlighted. Push the left Audio Menu icon/title is highlighted in the instrument or right arrow button to scroll the submenus, one with cluster display.
Page 155: Screen Setup Driver Selectable Items
GETTING TO KNOW YOUR INSTRUMENT PANEL 153 Speed Warning Gear Display • Full (default setting) Push and release the up or down arrow button until the Speed Warning Menu icon/title is highlighted in the • Single instrument cluster display. Push and release the OK button Favorite Menus to enter speed warning.
Page 156: Battery Saver On/Battery Saver Mode Message - Electrical Load Reduction Actions - If Equipped
154 GETTING TO KNOW YOUR INSTRUMENT PANEL • Trip A Upper Left • None • Trip B • Compass (default setting) Defaults (Restores All Settings To Default Settings) • Outside Temp • Restore • Time • Cancel • Range To Empty (RTE) Battery Saver On/Battery Saver Mode Message —...
Page 157 GETTING TO KNOW YOUR INSTRUMENT PANEL 155 When load reduction is activated, the message “Battery Loss of the battery charge may indicate one or more of the Saver On” or “Battery Saver Mode” will appear in the following conditions: instrument cluster. •...
Page 158: Warning Lights And Messages
156 GETTING TO KNOW YOUR INSTRUMENT PANEL • The battery was used for an extended period with the • The vehicle should have service performed if the mes- engine not running to supply radio, lights, chargers, sage is still present during consecutive trips and the +12V portable appliances like vacuum cleaners, game evaluation of the vehicle and driving pattern did not consoles and similar devices.
Page 159 GETTING TO KNOW YOUR INSTRUMENT PANEL 157 turn on. When driving, if the driver or front passenger seat If the light remains on when the parking brake has been belt remains unbuckled, the Seat Belt Reminder Light will disengaged, and the fluid level is at the full mark on the flash or remain on continuously and a chime will sound.
Page 160 158 GETTING TO KNOW YOUR INSTRUMENT PANEL — Battery Charge Warning Light WARNING! This light illuminates when the battery is not charging Driving a vehicle with the red brake light on is properly. If it stays on while the engine is running, there dangerous.
Page 161 GETTING TO KNOW YOUR INSTRUMENT PANEL 159 — Electronic Throttle Control (ETC) Warning — Engine Coolant Temperature Warning Light Light This light warns of an overheated engine condition. If the This light informs you of a problem with the Electronic engine coolant temperature is too high, this indicator will Throttle Control (ETC) system.
Page 162 160 GETTING TO KNOW YOUR INSTRUMENT PANEL — Liftgate Open Warning Light — Transmission Temperature Warning Light — If Equipped This indicator will turn when the liftgate is open. This light indicates high transmission fluid temperature. NOTE: If the vehicle is moving, there will also be a single This may occur with strenuous usage such as trailer chime.
Page 163: Yellow Warning Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL 161 — Vehicle Security Warning Light — If Equipped When the engine is running, the MIL may flash to alert serious conditions that could lead to immediate loss of This light will flash at a fast rate for approximately 15 power or severe catalytic converter damage.
Page 164 162 GETTING TO KNOW YOUR INSTRUMENT PANEL — Electronic Stability Control (ESC) Active — Electronic Stability Control (ESC) Off Warning Warning Light — If Equipped Light — If Equipped This light will indicate when the Electronic Stability Con- This light indicates the Electronic Stability Control (ESC) is trol system is Active.
Page 165 GETTING TO KNOW YOUR INSTRUMENT PANEL 163 Should one or more tires be in the condition mentioned more of your tires is significantly under-inflated. Accord- above, the display will show the indications corresponding ingly, when the low tire pressure telltale illuminates, you to each tire in sequence.
Page 166 164 GETTING TO KNOW YOUR INSTRUMENT PANEL TPMS malfunctions may occur for a variety of reasons, — Low Fuel Warning Light including the installation of replacement or alternate tires When the fuel level reaches approximately 2 gal (7.5 L), this or wheels on the vehicle that prevent the TPMS from light will turn on and a chime will sound.
Page 167: Yellow Indicator Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL 165 — Service Forward Collision Warning (FCW) — Service LaneSense Warning Light — Light — If Equipped If Equipped This telltale will turn on to indicate a fault in the Forward This light will turn on when the LaneSense system is not Collision Warning System.
Page 168 166 GETTING TO KNOW YOUR INSTRUMENT PANEL — ECO Mode Indicator Light — Snow Mode SRT Indicator Light This light will turn on when ECO Mode is active. This light will turn on when Snow Mode is active. — Cruise Control Set Indicator Light — —...
Page 169: White Indicator Lights
GETTING TO KNOW YOUR INSTRUMENT PANEL 167 White Indicator Lights For further information refer to “Instrument Cluster Dis- play Menu Items” in “Getting To Know Your Instrument — Adaptive Cruise Control (ACC) Ready Light — Panel.” If Equipped The number “55” is only an example of a speed that can be This light will turn on when Adaptive Cruise Control set.
Page 170: Blue Indicator Lights
168 GETTING TO KNOW YOUR INSTRUMENT PANEL Blue Indicator Lights Although your vehicle will usually be drivable and not need towing, see an authorized dealer for service as soon — High Beam Indicator Light as possible. This indicator shows that the high beam headlights are on. With the low beams activated, push the multifunction lever CAUTION! forward (toward the front of the vehicle) to turn on the...
Page 171: Emissions Inspection And Maintenance Programs
GETTING TO KNOW YOUR INSTRUMENT PANEL 169 EMISSIONS INSPECTION AND MAINTENANCE WARNING! PROGRAMS • ONLY an authorized service technician should con- In some localities, it may be a legal requirement to pass an nect equipment to the OBD II connection port in inspection of your vehicle’s emissions control system.
Page 172 170 GETTING TO KNOW YOUR INSTRUMENT PANEL 2. As soon as you cycle the ignition switch to the ON Regardless of whether your vehicle’s OBD II system is position, you will see the “Malfunction Indicator Light ready or not, if the MIL is illuminated during normal (MIL)”...
Page 173 SAFETY CONTENTS ▫ Seat Belt Systems ..... .202 SAFETY FEATURES ..... .172 ▫...
Page 174: Safety Features
172 SAFETY SAFETY FEATURES These are all normal characteristics of ABS. Anti-Lock Brake System (ABS) WARNING! The Anti-Lock Brake System (ABS) provides increased • The ABS contains sophisticated electronic equip- vehicle stability and brake performance under most brak- ment that may be susceptible to interference caused ing conditions.
Page 175: Electronic Brake Control System
SAFETY Electronic Brake Control System WARNING! (Continued) Your vehicle is equipped with an advanced Electronic • The capabilities of an ABS equipped vehicle must Brake Control system (EBC). This system includes Elec- never be exploited in a reckless or dangerous manner tronic Brake Force Distribution (EBD), Anti-Lock Brake that could jeopardize the user’s safety or the safety of System (ABS), Brake Assist System (BAS), Hill Start Assist...
Page 176 174 SAFETY If the “Brake System Warning Light” remains on or comes WARNING! on while driving, it indicates that the brake system is not functioning properly and that immediate service is re- The Brake Assist System (BAS) cannot prevent the quired.
Page 177 SAFETY The following conditions must be met in order for HSA to WARNING! (Continued) activate: while pulling a trailer. HSA is not a substitute for • The feature must be enabled. active driving involvement. It is always the driver’s • The vehicle must be stopped. responsibility to be attentive to distance to other ve- hicles, people, and objects, and most importantly brake •...
Page 178 176 SAFETY For vehicles not equipped with an instrument cluster Towing With HSA display, perform the following steps: HSA will also provide assistance to mitigate roll back while towing a trailer. 1. Center the steering wheel (front wheels pointing straight forward). WARNING! 2.
Page 179 SAFETY • Oversteer — when the vehicle is turning more than reduce engine power to provide enhanced acceleration and stability. A feature of the TCS, Brake Limited Differential appropriate for the steering wheel position. (BLD), functions similar to a limited slip differential and •...
Page 180 178 SAFETY ESC On WARNING! (Continued) This is the normal operating mode for the ESC. Whenever from loss of vehicle control due to inappropriate the vehicle is started, the ESC system will be in this mode. driver input for the conditions. Only a safe, attentive, This mode should be used for most driving conditions.
Page 181 SAFETY NOTE: System may switch from ESC “Full Off” to “Partial WARNING! Off” mode when vehicle exceeds a predetermined speed. • When in “Partial Off” mode, the TCS functionality When the vehicle speed slows below the predetermined speed the system will return to ESC “Full Off”. of ESC, (except for the limited slip feature described in the TCS section), has been disabled and the “ESC “Full Off”...
Page 182 180 SAFETY The “ESC Activation/Malfunction Indicator Light” (lo- WARNING! (Continued) cated in the instrument cluster) starts to flash as soon as the • The Electronic Stability Control (ESC) cannot pre- tires lose traction and the ESC system becomes active. The vent the natural laws of physics from acting on the “ESC Activation/Malfunction Indicator Light”...
Page 183 SAFETY Electronic Roll Mitigation (ERM) Trailer Sway Control (TSC) This system anticipates the potential for wheel lift by TSC uses sensors in the vehicle to recognize an excessively monitoring the driver’s steering wheel input and the speed swaying trailer and will take the appropriate actions to of the vehicle.
Page 184: Auxiliary Driving Systems
182 SAFETY Ready Alert Braking (RAB) reach/maintain vehicle stability. The only notification the driver receives that the feature is active is the torque Ready Alert Braking may reduce the time required to reach applied to the steering wheel. full braking during emergency braking situations. It antici- pates when an emergency braking situation may occur by NOTE: The DST feature is only meant to help the driver monitoring how fast the throttle is released by the driver.
Page 185 SAFETY vehicle when the vehicle speed has reached approximately 6 mph (10 km/h) or higher and will alert the driver of vehicles in these areas. NOTE: • The BSM system DOES NOT alert the driver about rapidly approaching vehicles that are outside the detec- tion zones.
Page 186 184 SAFETY The area on the rear fascia where the radar sensors are signal is activated during the alert on the side of the vehicle located must remain free of snow, ice, and dirt/road corresponding to the alert, an audible (chime) alert can be contamination so that the BSM system can function prop- heard.
Page 187 SAFETY Entering From The Side Entering From The Rear Vehicles that move into your adjacent lanes from either Vehicles that come up from behind your vehicle on either side of the vehicle. side and enter the rear detection zone with a relative speed of less than 30 mph (48 km/h).
Page 188 186 SAFETY Overtaking Traffic If you pass another vehicle slowly (with a relative speed of less than 15 mph (24 km/h)) and the vehicle remains in the blind spot for approximately 1.5 seconds, the warning light will be illuminated. If the difference in speed between the two vehicles is greater than 15 mph (24 km/h), the warning light will not illuminate.
Page 189 SAFETY The BSM system is designed not to issue an alert on stationary objects such as guardrails, posts, walls, foliage, berms, etc. However, occasionally the system may alert on such objects. This is normal operation and your vehicle does not require service. Opposing Traffic WARNING! The Blind Spot Monitoring system is only an aid to...
Page 190 188 SAFETY Rear Cross Path (RCP) (5 km/h), to objects moving a maximum of approximately 20 mph (32 km/h), such as in parking lot situations. The Rear Cross Path (RCP) feature is intended to aid the driver when backing out of parking spaces where their NOTE: In a parking lot situation, oncoming vehicles can be vision of oncoming vehicles may be blocked.
Page 191 SAFETY Modes Of Operation NOTE: Whenever an audible alert is requested by the BSM system, the radio is also muted. Three selectable modes of operation are available in the Uconnect System. Refer to “Uconnect Settings” in “Multi- When the system is in RCP, the system shall respond with media”...
Page 192: Forward Collision Warning (Fcw) With Mitigation
190 SAFETY General Information NOTE: FCW monitors the information from the forward looking sensors as well as the Electronic Brake Controller The following regulatory statement applies to all Radio (EBC), to calculate the probability of a forward collision. Frequency (RF) devices equipped in this vehicle: When the system determines that a forward collision is This device complies with Part 15 of the FCC Rules and probable, the driver will be provided with audible and...
Page 193 SAFETY • It is unsafe to test the FCW system. To prevent such misuse of the system, after four Active Braking events within an ignition cycle, the Active Braking portion of FCW will be deactivated until the next ignition cycle. •...
Page 194 192 SAFETY The default sensitivity of FCW is the “Medium” setting NOTE: and the system status is “Warning & Braking”. This allows • Changing the FCW status to “Only Warning” prevents the system to warn the driver of a possible collision with the system from providing limited active braking, or the vehicle in front using audible/visual warnings and it additional brake support if the driver is not braking...
Page 195 SAFETY FCW Limited Warning General Information If the instrument cluster displays “ACC/FCW Limited The following regulatory statement applies to all Radio Functionality” or “ACC/FCW Limited Functionality Clean Frequency (RF) devices equipped in this vehicle: Front Windshield” momentarily, there may be a condition This device complies with Part 15 of the FCC Rules and that limits FCW functionality.
Page 196: Tire Pressure Monitor System (Tpms)
194 SAFETY Tire Pressure Monitor System (TPMS) tires. The tire pressure will also increase as the vehicle is driven - this is normal and there should be no adjustment NOTE: For vehicles equipped with run flat tires — when for this increased pressure. the TPMS indicates a tire pressure of 14 psi (96 kPa) or The TPMS will warn the driver of a low tire pressure if the lower, always check tire pressure and replace the tire at the...
Page 197 SAFETY For example, your vehicle has a recommended cold CAUTION! (Continued) (parked for more than three hours) tire pressure of 33 psi a poor overall system performance or sensor damage. (227 kPa). If the ambient temperature is 68°F (20°C) and the Customers are encouraged to use OEM wheels to measured tire pressure is 28 psi (193 kPa), a temperature assure proper TPM feature operation.
Page 198 196 SAFETY • Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under- inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. • The TPMS is not a substitute for proper tire mainte- nance, and it is the driver’s responsibility to maintain correct tire pressure using an accurate tire gauge, even if under-inflation has not reached the level to trigger...
Page 199 SAFETY Tire Pressure Monitoring Low Pressure Warnings The Tire Pressure Monitoring Telltale Light will illuminate in the instrument cluster, and an audible chime will be activated, when one or more of the four active road tire pressures are low. In addition, the instru- ment cluster will display an Inflate to XX message and a graphic display of the pressure value(s) with the low tire(s) in a different color.
Page 200 198 SAFETY The system will automatically update, the graphic display A system fault can occur by any of the following: of the pressure value(s) will return to its original color and • Jamming due to electronic devices or driving next to the Tire Pressure Monitoring Telltale Light will extinguish facilities emitting the same Radio Frequencies as the once the updated tire pressure(s) have been received.
Page 201 SAFETY NOTE: There is no tire pressure monitoring sensor in the In addition, the Tire Pressure Monitoring Telltale Light will spare tire. The TPMS will not be able to monitor the tire turn off and the graphic in the instrument cluster display pressure.
Page 202: Occupant Restraint Systems
200 SAFETY Beginning with the next ignition cycle, the TPMS will no NOTE: Changes or modifications not expressly approved longer chime or display the “SERVICE TPM SYSTEM” by the party responsible for compliance could void the message in the instrument cluster but dashes (--) will user’s authority to operate the equipment.
Page 203 SAFETY Here are some simple steps you can take to minimize the 6. All occupants should always wear their lap and shoul- risk of harm from a deploying air bag: der belts properly. 1. Children 12 years old and under should always ride 7.
Page 204: Seat Belt Systems
202 SAFETY Seat Belt Systems a few seconds. If the driver or outboard front seat passen- ger (if equipped with outboard front passenger seat Buckle up even though you are an excellent driver, even on BeltAlert) is unbuckled when the ignition switch is first in short trips.
Page 205 SAFETY Change of Status Lap/Shoulder Belts All seating positions in your vehicle are equipped with If the driver or outboard front seat passenger (if equipped lap/shoulder belts. with outboard front passenger seat BeltAlert) unbuckles their seat belt while the vehicle is traveling, the BeltAlert The seat belt webbing retractor will lock only during very warning sequence will begin until the seat belts are buck- sudden stops or collisions.
Page 206 204 SAFETY WARNING! (Continued) WARNING! • It is dangerous to ride in a cargo area, inside or • A lap belt worn too high can increase the risk of outside of a vehicle. In a collision, people riding in injury in a collision. The seat belt forces won’t be at these areas are more likely to be seriously injured or the strong hip and pelvic bones, but across your killed.
Page 207 SAFETY Lap/Shoulder Belt Operating Instructions WARNING! (Continued) 1. Enter the vehicle and close the door. Sit back and adjust vehicle in a collision, increasing head and neck the seat. injury. A seat belt worn under the arm can cause internal injuries. Ribs aren’t as strong as shoulder 2.
Page 208 206 SAFETY 3. When the seat belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.” Positioning The Lap Belt 5. Position the shoulder belt across the shoulder and chest with minimal, if any slack so that it is comfortable and Inserting Latch Plate Into Buckle not resting on your neck.
Page 209 SAFETY Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/ shoulder belt. 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the seat belt webbing 180 degrees to create a fold that begins immediately above the latch plate.
Page 210 208 SAFETY NOTE: The adjustable upper shoulder belt anchorage is Seat Belt Extender equipped with an Easy Up feature. This feature allows the If a seat belt is not long enough to fit properly, even when shoulder belt anchorage to be adjusted in the upward the webbing is fully extended and the adjustable upper position without pushing or squeezing the release button.
Page 211 SAFETY Seat Belts And Pregnant Women Seat Belt Pretensioner The front seat belt system is equipped with pretensioning devices that are designed to remove slack from the seat belt in the event of a collision. These devices may improve the performance of the seat belt by removing slack from the seat belt early in a collision.
Page 212 210 SAFETY Switchable Automatic Locking Retractor (ALR) The seat belts in the passenger seating positions are equipped with a Switchable Automatic Locking Retractor (ALR) which is used to secure a child restraint system. For additional information, refer to “Installing Child Restraints Using The Vehicle Seat Belt”...
Page 213 SAFETY In Automatic Locking Mode, the shoulder belt is automati- cally pre-locked. The seat belt will still retract to remove any slack in the shoulder belt. Use the Automatic Locking Mode anytime a child restraint is installed in a seating position that has a seat belt with this feature.
Page 214 212 SAFETY 3. Allow the seat belt to retract. As the seat belt retracts, Supplemental Active Head Restraints (AHR) you will hear a clicking sound. This indicates the seat These head restraints are passive, deployable components, belt is now in the Automatic Locking Mode. and vehicles with this equipment cannot be readily iden- tified by any markings, only through visual inspection of How To Disengage The Automatic Locking Mode...
Page 215 SAFETY NOTE: The Active Head Restraints (AHR) may or may not WARNING! deploy in the event of a front or side impact. However, if • All occupants, including the driver, should not oper- during a front impact, a secondary rear impact occurs, the AHR may deploy based on the severity and type of the ate a vehicle or sit in a vehicle’s seat until the head impact.
Page 216: Supplemental Restraint Systems (Srs)
214 SAFETY Resetting Active Head Restraints (AHR) WARNING! Deployed AHRs are not able to best protect you in all types of collisions. Have deployed AHRs reset by an authorized dealer immediately. Supplemental Restraint Systems (SRS) Some of the safety features described in this section may be standard equipment on some models, or may be optional equipment on others.
Page 217 SAFETY • Knee Impact Bolsters The ORC turns on the Air Bag Warning Light in the instrument panel for approximately four to eight seconds • Driver and Front Passenger Air Bags for a self-check when the ignition switch is first in the •...
Page 218 216 SAFETY NOTE: If the speedometer, tachometer, or any engine Redundant Air Bag Warning Light related gauges are not working, the Occupant Restraint If a fault with the Air Bag Warning Light is Controller (ORC) may also be disabled. In this condition detected, which could affect the Supplemental the air bags may not be ready to inflate for your protection.
Page 219 SAFETY WARNING! (Continued) to reach the steering wheel or instrument panel. • Never place a rear-facing child restraint in front of an air bag. A deploying passenger front air bag can cause death or serious injury to a child 12 years or younger, including a child in a rear-facing child restraint.
Page 220 218 SAFETY This vehicle may be equipped with a driver and/or front WARNING! (Continued) passenger seat belt buckle switch that detects whether the • Relying on the air bags alone could lead to more driver or front passenger seat belt is buckled. The seat belt severe injuries in a collision.
Page 221 SAFETY Seat belts are necessary for your protection in all collisions, Supplemental Driver Knee Air Bag and also are needed to help keep you in position, away This vehicle is equipped with a Supplemental Driver Knee from an inflating air bag. Air Bag mounted in the instrument panel below the When the ORC detects a collision requiring the front air steering column.
Page 222 220 SAFETY The SABs may help to reduce the risk of occupant injury When the SAB deploys, it opens the seam on the outboard during certain side impacts, in addition to the injury side of the seatback’s trim cover. The inflating SAB deploys reduction potential provided by the seat belts and body through the seat seam into the space between the occupant structure.
Page 223 SAFETY The SABICs may help reduce the risk of partial or complete ejection of vehicle occupants through side windows in certain side impact events. WARNING! • Do not mount equipment, or stack luggage or other cargo up high enough to block the deployment of the SABICs.
Page 224 222 SAFETY ORC in determining the appropriate response to impact WARNING! (Continued) events. The system is calibrated to deploy the Side Air Bags never lean on or sleep against the door, side win- on the impact side of the vehicle during impacts that dows, or area where the side air bags inflate, even if require Side Air Bag occupant protection.
Page 225 SAFETY event, and deployment of the Side Air Bags is appropriate, WARNING! (Continued) the rollover sensing system will also deploy the seat belt • Relying on the Side Air Bags alone could lead to pretensioners on both sides of the vehicle. more severe injuries in a collision.
Page 226 224 SAFETY • Seat Belt Pretensioners inflation. These airborne particles may irritate the skin, eyes, nose, or throat. If you have skin or eye irritation, • Seat Track Position Sensors rinse the area with cool water. For nose or throat If A Deployment Occurs irritation, move to fresh air.
Page 227 SAFETY Enhanced Accident Response System Maintaining Your Air Bag System In the event of an impact, if the communication network WARNING! remains intact, and the power remains intact, depending on the nature of the event, the ORC will determine whether •...
Page 228: Child Restraints
226 SAFETY These data can help provide a better understanding of the WARNING! (Continued) circumstances in which crashes and injuries occur. dealer. Only manufacturer approved seat accessories NOTE: EDR data are recorded by your vehicle only if a may be used. If it is necessary to modify the air bag non-trivial crash situation occurs;...
Page 229 SAFETY Children 12 years or younger should ride properly buckled Before buying any restraint system, make sure that it has a up in a rear seat, if available. According to crash statistics, label certifying that it meets all applicable Safety Stan- children are safer when properly restrained in the rear dards.
Page 230 228 SAFETY Summary Of Recommendations For Restraining Children In Vehicles Recommended Type Child Size, Height, Weight Or Age Of Child Restraint Infants and Toddlers Children who are two years old or Either an Infant Carrier or a younger and who have not reached Convertible Child Restraint, the height or weight limits of their facing rearward in the rear seat of...
Page 231 SAFETY Infant And Child Restraints WARNING! (Continued) Safety experts recommend that children ride rear-facing in • Only use a rear-facing child restraint in a vehicle the vehicle until they are two years old or until they reach with a rear seat. either the height or weight limit of their rear-facing child restraint.
Page 232 230 SAFETY should use the seat belt in a rear seat. Use this simple 5-step WARNING! test to decide whether the child can use the vehicle’s seat • Improper installation can lead to failure of an infant belt alone: or child restraint. It could come loose in a collision. 1.
Page 233 SAFETY WARNING! Never allow a child to put the shoulder belt under an arm or behind their back. In a crash, the shoulder belt will not protect a child properly, which may result in serious injury or death. A child must always wear both the lap and shoulder portions of the seat belt correctly.
Page 234 232 SAFETY Lower Anchors And Tethers For CHildren (LATCH) In these seating positions, the seat belt must be used with Restraint System the top tether anchorage to install the child restraint. Please see the following table for more information. LATCH Positions For Installing Child Restraints In This Vehicle LATCH Label Your vehicle is equipped with the child restraint anchorage...
Page 235 SAFETY 60/40 Second Row LATCH Positions (7 Passenger) Captain’s Chairs Second Row LATCH Positions (6 Passenger) Lower Anchorage Symbol (2 Anchorages Per Seating Position) Top Tether Anchorage Symbol Lower Anchorage Symbol (2 Anchorages Per Seating Position) Top Tether Anchorage Symbol...
Page 236 234 SAFETY Frequently Asked Questions About Installing Child Restraints With LATCH What is the weight limit 65 lbs (29.5 kg) Use the LATCH anchorage system (child’s weight + weight of the until the combined weight of the child restraint) for using the child and the child restraint is 65 lbs LATCH anchorage system to attach (29.5 kg).
Page 237 SAFETY Frequently Asked Questions About Installing Child Restraints With LATCH Can two child restraints be Never “share” a LATCH anchorage attached using a common lower with two or more child restraints. LATCH anchorage? If the center position does not have dedicated LATCH lower anchorages, use the seat belt to install a child seat in the center position next to a child...
Page 238 236 SAFETY Locating The LATCH Anchorages The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback. They are just visible when you lean into the rear seat to install the child restraint.
Page 239 SAFETY Seven Passenger Rear Seat Lower Anchorages Six Passenger Top Tether Strap Mounting (Captain’s Chair) Locating The Upper Tether Anchorages 2nd Row Upper Tether Anchorage Locations There are tether strap anchorages behind each rear seating position located on the back of the seat.
Page 240 238 SAFETY Pulling Down The Carpet Floor Panel To Access Top Five Passenger Top Tether Strap Mounting Tether Strap Anchorage (Five Passenger)
Page 241 SAFETY Seven Passenger Top Tether Strap Mounting Pulling Down The Carpet Floor Panel To Access (2nd Row Bench) Top Tether Strap...
Page 242 240 SAFETY Center Seat LATCH — Five Or Seven Second Row Passenger Seating Only WARNING! • Do not install a child restraint in the center position using the LATCH system. This position is not ap- proved for installing child seats using the LATCH attachments.
Page 243 SAFETY 1. To access the center seat arm rest tether, first lower the 2. Pull down on the tether to unhook it from the plastic arm rest. The tether is located behind the armrest and seat backing. hooked onto the plastic seat backing. Center Seat Position Arm Rest Tether Center Seat Position Arm Rest Tether 3.
Page 244 242 SAFETY To Install A LATCH-Compatible Child Restraint 4. If the child restraint has a tether strap, connect it to the top tether anchorage. See the section “Installing Child If the selected seating position has a Switchable Automatic Restraints Using the Top Tether Anchorage” for direc- Locking Retractor (ALR) seat belt, stow the seat belt, tions to attach a tether anchor.
Page 245 SAFETY If the buckled seat belt interferes with the child restraint Installing Child Restraints Using The Vehicle Seat installation, instead of buckling it behind the child re- Belt straint, route the seat belt through the child restraint belt Child restraint systems are designed to be secured in path and then buckle it.
Page 246 244 SAFETY The ALR retractor can be “switched” into a locked mode by Lap/Shoulder Belt Systems For Installing Child pulling all of the webbing out of the retractor and then Restraints In This Vehicle letting the webbing retract back into the retractor. If it is locked, the ALR will make a clicking noise while the webbing is pulled back into the retractor.
Page 247 SAFETY 60/40 Second Row (7 Passenger) Captain’s Chairs Second Row (6 Passenger) Automatic Locking Retractor (ALR) Locations Automatic Locking Retractor (ALR) Locations ALR = Switchable Automatic Locking Retractor ALR = Switchable Automatic Locking Retractor Top Tether Anchorage Symbol Top Tether Anchorage Symbol...
Page 248 246 SAFETY Frequently Asked Questions About Installing Child Restraints With Seat Belts What is the weight limit Weight limit of the Child Restraint Always use the tether anchor when (child’s weight + weight of the child using the seat belt to install a restraint) for using the Tether Anchor forward facing child restraint, up to with the seat belt to attach a forward...
Page 249 SAFETY Installing A Child Restraint With A Switchable 3. Slide the latch plate into the buckle until you hear a Automatic Locking Retractor (ALR): “click.” Child restraint systems are designed to be secured in 4. Pull on the webbing to make the lap portion tight vehicle seats by lap belts or the lap belt portion of a against the child seat.
Page 250 248 SAFETY 8. If the child restraint has a top tether strap and the Installing Child Restraints Using The Top Tether seating position has a top tether anchorage, connect the Anchorage tether strap to the anchorage and tighten the tether strap.
Page 251 SAFETY 1. Look behind the seating position where you plan to install the child restraint to find the tether anchorage. You may need to move the seat forward to provide better access to the tether anchorage. If there is no top tether anchorage for that seating position, move the child restraint to another position in the vehicle if one is available.
Page 252 250 SAFETY 4. For the center seating position, route the tether strap over the seatback and headrest then attach the hook to the tether anchor located on the back of the seat. 5. Attach the tether strap hook of the child restraint to the top tether anchorage as shown in the diagram.
Page 253 SAFETY Bench Seat Top Tether Strap Mounting Captain’s Chair Top Tether Strap Mounting (7 Passenger Seating) 6. Remove slack in the tether strap according to the child restraint manufacturer’s instructions. WARNING! • The top tether anchorages are not visible until the gap panel is folded down.
Page 254: Transporting Pets
252 SAFETY WARNING! (Continued) WARNING! child. Use only the anchorage position directly be- • Do not leave children or animals inside parked hind the child seat to secure a child restraint top vehicles in hot weather. Interior heat build-up may tether strap.
Page 255: Safety Checks You Should Make Inside
SAFETY Safety Checks You Should Make Inside The Vehicle WARNING! (Continued) Seat Belts confined areas any longer than needed to move your vehicle in or out of the area. Inspect the seat belt system periodically, checking for cuts, • If you are required to drive with the trunk/liftgate/ frays, and loose parts.
Page 256 254 SAFETY Defroster WARNING! (Continued) Check operation by selecting the defrost mode and place the upside down or turn your floor mat over. Lightly pull blower control on high speed. You should be able to feel the air to confirm mat is secured using the floor mat fasten- directed against the windshield.
Page 257: The Vehicle
SAFETY Periodic Safety Checks You Should Make Outside WARNING! (Continued) The Vehicle • ONLY use the passenger’s side floor mat on the Tires passenger’s side floor area. • ALWAYS make sure objects cannot fall or slide into Examine tires for excessive tread wear and uneven wear the driver’s side floor area when the vehicle is patterns.
Page 258 256 SAFETY WARNING! WARNING! To prevent SERIOUS INJURY or DEATH when using To prevent SERIOUS INJURY or DEATH: • ALWAYS remove any “Track-Use” equipment before “Track-Use” parts and equipment: • NEVER use any “Track-Use” equipment on public driving on public roads. •...
Page 259 STARTING AND OPERATING CONTENTS ▫ Eight-Speed Automatic Transmission ..270 STARTING THE ENGINE ....260 ▫ Automatic Transmission ....260 ▫...
Page 260 258 STARTING AND OPERATING ▫ To Accelerate For Passing ....285 ▫ Display Warnings And Maintenance ..298 ▫...
Page 261 STARTING AND OPERATING 259 ▫ Enabling And Disabling ParkSense ..325 ▫ Rim Size ......338 ▫...
Page 262: Starting The Engine
260 STARTING AND OPERATING STARTING THE ENGINE WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust the inside • Do not leave children or animals inside parked and outside mirrors, fasten your seat belt, and if present, vehicles in hot weather. Interior heat build-up may instruct all other occupants to buckle their seat belts.
Page 263: Keyless Enter-N-Go - Ignition
STARTING AND OPERATING 261 Keyless Enter-N-Go — Ignition 2. Press and hold the brake pedal while pushing the ENGINE START/STOP button once. 3. The system takes over and attempts to start the vehicle. If the vehicle fails to start, the starter will disengage automatically after 10 seconds.
Page 264 262 STARTING AND OPERATING 4. If the gear selector is not in PARK and the ENGINE 3. Push the ENGINE START/STOP button a second time START/STOP button is pushed once with the vehicle to place the ignition to the RUN mode. speed above 5 MPH (8 km/h), the instrument cluster 4.
Page 265 STARTING AND OPERATING 263 AutoPark will engage when all of these conditions are met: WARNING! (Continued) • Vehicle is equipped with an 8-speed transmission • AutoPark is a supplemental feature. It is not de- • Vehicle is not in PARK signed to replace the need to shift your vehicle into PARK.
Page 266: If Engine Fails To Start
264 STARTING AND OPERATING If Engine Fails To Start WARNING! WARNING! If vehicle speed is above 1.2 MPH (1.9 km/h), the transmission will default to NEUTRAL until the ve- • Never pour fuel or other flammable liquid into the hicle speed drops below 1.2 MPH (1.9 km). A vehicle throttle body air inlet opening in an attempt to start left in the NEUTRAL position can roll.
Page 267: After Starting
STARTING AND OPERATING 265 • Avoid aggressive braking. After Starting • Drive with the engine speed less than 3,500 RPM. The idle speed is controlled automatically, and it will decrease as the engine warms up. • Maintain vehicle speed below 55 mph (88 km/h) and observe local speed limits.
Page 268: Parking Brake
266 STARTING AND OPERATING For the first 1500 miles (2414 km): • Do not participate in track events, sport driving schools, or similar activities during the first 1500 miles (2414 km). NOTE: Check engine oil with every refueling and add if necessary.
Page 269 STARTING AND OPERATING 267 When parking on a hill, it is important to turn the front WARNING! (Continued) wheels toward the curb on a downhill grade and away • When leaving the vehicle, always make sure the from the curb on an uphill grade. Apply the parking brake keyless ignition node is in the OFF mode, remove the before placing the gear selector in PARK, otherwise the key fob from the vehicle and lock the vehicle.
Page 270: Automatic Transmission
268 STARTING AND OPERATING CAUTION! WARNING! (Continued) vehicle is completely stopped, and the PARK posi- If the Brake Warning Light remains on with the park- tion is properly indicated, before exiting the vehicle. ing brake released, a brake system malfunction is •...
Page 271: Ignition Park Interlock
STARTING AND OPERATING 269 NOTE: You must press and hold the brake pedal while WARNING! (Continued) shifting out of PARK. • Never leave children alone in a vehicle, or with Ignition Park Interlock access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number This vehicle is equipped with an Ignition Park Interlock of reasons.
Page 272: Fuel Economy (Eco) Mode
270 STARTING AND OPERATING Fuel Economy (ECO) Mode You must also press the brake pedal to shift from NEU- TRAL into DRIVE or REVERSE when the vehicle is The Fuel Economy (ECO) mode can improve the vehicle’s stopped or moving at low speeds (refer to “Brake/ overall fuel economy during normal driving conditions.
Page 273 STARTING AND OPERATING 271 The transmission gear selector provides PARK, REVERSE, NEUTRAL, DRIVE and MANUAL (AutoStick) shift posi- tions. Manual shifts can be made using the AutoStick shift control. Toggling the gear selector forward (-) or rearward (+) while in the MANUAL (AutoStick) position (beside the DRIVE position), or tapping the shift paddles (+/-), will manually select the transmission gear, and will display the current gear in the instrument cluster.
Page 274 272 STARTING AND OPERATING PARK (P) WARNING! This range supplements the parking brake by locking the • Never use the PARK position as a substitute for the transmission. The engine can be started in this range. parking brake. Always apply the parking brake fully Never attempt to use PARK while the vehicle is in motion.
Page 275 STARTING AND OPERATING 273 WARNING! (Continued) WARNING! (Continued) engine is idling normally and your foot is firmly a location accessible to children), and do not leave pressing the brake pedal. the ignition in the ACC or ON/RUN mode. A child •...
Page 276 274 STARTING AND OPERATING • Look at the transmission gear position display and WARNING! verify that it indicates the PARK position (P), and is not blinking. Do not coast in NEUTRAL and never turn off the ignition to coast down a hill. These are unsafe practices •...
Page 277 STARTING AND OPERATING 275 When frequent transmission shifting occurs (such as when (AutoStick) position will manually select the transmission operating the vehicle under heavy loading conditions, in gear, and will display the current gear in the instrument hilly terrain, traveling into strong head winds, or while cluster.
Page 278: Autostick
276 STARTING AND OPERATING 1. Stop the vehicle. and reduce the potential for transmission overheating or failure due to excessive shifting. Refer to “Selec-Track” in 2. Shift the transmission into PARK, if possible. If not, shift “Starting And Operating” for further information. the transmission to NEUTRAL.
Page 279 STARTING AND OPERATING 277 • If a requested downshift would cause the engine to the (-) shift paddle on the steering wheel, will downshift the transmission to the next lower gear. Tapping the over-speed, that shift will not occur. selector rearward (+) (or tapping the (+) shift paddle) will •...
Page 280: Drive Modes
278 STARTING AND OPERATING DRIVE MODES Preconditions: • Launch control should not be used on public roads. Your SRT vehicle is equipped with a SRT Drive Mode Always check track conditions and the surrounding feature. This feature gives the driver control over the area.
Page 281 STARTING AND OPERATING 279 2. Push the “Launch RPM Set-Up” button on the touch- Launch control will be active until the vehicle reaches screen. This screen will allow you to adjust your launch 62 mph (100 km/h), at which point the ESC system will RPM’s for optimum launch/traction.
Page 282: Guidelines For Track Use
280 STARTING AND OPERATING • It is recommended that each track outing should end Guidelines For Track Use with a minimum of one cool down lap using minimal NOTE: Because of the extreme conditions encountered braking. during track use, any damage or wear associated with •...
Page 283 STARTING AND OPERATING 281 NOTE: It is recommended that you target 40psi (276kpa) 4. Allow vehicle to sit and cool in the paddock for at least Hot Tire Pressure at the conclusion of each track session. 30 min. If an infrared thermal gun is available, allow Starting at 32psi (221kpa) Front and 30psi (207 kpa) Rear rotors to cool to 200°F (93.3°C) before going back out.
Page 284: All-Wheel Drive Operation
282 STARTING AND OPERATING ALL-WHEEL DRIVE OPERATION POWER STEERING The electric power steering system will give you good Single-Speed Operating Instructions/Precautions vehicle response and increased ease of maneuverability in This system contains a single-speed (HI range only) trans- tight spaces. The system will vary its assist to provide light fer case, which provides convenient full-time all-wheel efforts while parking and good feel while driving.
Page 285: Speed Control - If Equipped
STARTING AND OPERATING 283 “Warning Lights And Messages” in “Getting To Know Your Instrument Panel” for further information. NOTE: • Even if the power steering assistance is no longer operational, it is still possible to steer the vehicle. Under these conditions there will be a substantial increase in steering effort, especially at low speeds and during parking maneuvers.
Page 286: To Activate
284 STARTING AND OPERATING To Set A Desired Speed WARNING! Turn the Speed Control on. When the vehicle has reached Speed Control can be dangerous where the system the desired speed, push the SET (+) or SET (-) button and cannot maintain a constant speed.
Page 287: To Accelerate For Passing
STARTING AND OPERATING 285 • If the button is continually pushed, the set speed will • If the button is continually pushed, the set speed will continue to increase until the button is released, then the continue to decrease until the button is released, then the new set speed will be established.
Page 288: To Resume Speed
286 STARTING AND OPERATING ADAPTIVE CRUISE CONTROL (ACC) — WARNING! IF EQUIPPED Speed Control can be dangerous where the system Adaptive Cruise Control (ACC) increases the driving con- cannot maintain a constant speed. Your vehicle could venience provided by cruise control while traveling on go too fast for the conditions, and you could lose highways and major roadways.
Page 289 STARTING AND OPERATING 287 The Cruise Control system has two control modes: WARNING! (Continued) • Adaptive Cruise Control mode for maintaining an ap- Your complete attention is always required while propriate distance between vehicles. driving to maintain safe control of your vehicle. •...
Page 290: Adaptive Cruise Control (Acc) Operation
288 STARTING AND OPERATING WARNING! (Continued) You should switch off the ACC system: • When driving in fog, heavy rain, heavy snow, sleet, heavy traffic, and complex driving situations (i.e., in highway construction zones). • When entering a turn lane or highway off ramp; when driving on roads that are winding, icy, snow- covered, slippery, or have steep uphill or downhill slopes.
Page 291: Activating Adaptive Cruise Control (Acc)
STARTING AND OPERATING 289 • When the driver’s seat belt is unbuckled at low speeds. Activating Adaptive Cruise Control (ACC) • ESC Full-Off Mode is active. You can only engage ACC if the vehicle speed is above 0 mph (0 km/h). To Activate/Deactivate The minimum set speed for the ACC system is 20 mph Push and release the Adaptive Cruise Control (ACC)
Page 292: To Set A Desired Acc Speed
290 STARTING AND OPERATING To turn the system off, push and release the Adaptive To Set A Desired ACC Speed Cruise Control (ACC) on/off button again. At this time, the When the vehicle reaches the speed desired, push the SET system will turn off and the instrument cluster displays (+) button or the SET (-) button and release.
Page 293: To Cancel
STARTING AND OPERATING 291 • The Normal (Fixed Speed) Cruise Control on/off button To Cancel is pushed. The following conditions cancel the system: • The ignition is turned OFF. • The brake pedal is applied. To Resume • The CANC button is pushed. If there is a set speed in memory push the RES (resume) •...
Page 294: To Vary The Speed Setting
292 STARTING AND OPERATING • If the button is continually pushed, the set speed will To Vary The Speed Setting continue to increase in 10 km/h increments until the To Increase Speed button is released. The increase in set speed is reflected While ACC is set, you can increase the set speed by in the instrument cluster display.
Page 295: Setting The Following Distance In Acc
STARTING AND OPERATING 293 • The ACC system maintains set speed when driving up Metric Speed (km/h) hill and down hill. However, a slight speed change on • Pushing the SET (-) button once will result in a 1 km/h moderate hills is normal.
Page 296 294 STARTING AND OPERATING Distance Setting 4 Bars (Longest) Distance Setting 3 Bars (Long)
Page 297 STARTING AND OPERATING 295 Distance Setting 2 Bars (Medium) Distance Setting 1 Bar (Short) To increase the distance setting, push the Distance Setting — Increase button and release. Each time the button is pushed, the distance setting increases by one bar (longer). To decrease the distance setting, push the Distance Setting —...
Page 298: Overtake Aid
296 STARTING AND OPERATING Indicator” icon, and the system adjusts vehicle speed automatically to maintain the distance setting, regardless of the set speed. The vehicle will then maintain the set distance until: • The vehicle ahead accelerates to a speed above the set speed.
Page 299: Acc Operation At Stop
STARTING AND OPERATING 297 ACC Operation At Stop WARNING! If the ACC system brings your vehicle to a standstill while When the ACC system is resumed, the driver must following a target vehicle, if the target vehicle starts ensure that there are no pedestrians, vehicles or objects moving within two seconds of your vehicle coming to a in the path of the vehicle.
Page 300: Display Warnings And Maintenance
298 STARTING AND OPERATING Adaptive Cruise Control Set Display Warnings And Maintenance When the SET (+) or the SET (-) button (located on the “Wipe Front Radar Sensor In Front Of Vehicle” steering wheel) is pushed, the display will read “ACC Warning SET.”...
Page 301 STARTING AND OPERATING 299 NOTE: If the “ACC/FCW Unavailable Wipe Front Radar When the condition that deactivated the system is no Sensor” warning is active Normal (Fixed Speed) Cruise longer present, the system will return to the “Adaptive Control is still available. For additional information refer to Cruise Control Off”...
Page 302: Precautions While Driving With Acc
300 STARTING AND OPERATING display “ACC/FCW Limited Functionality Clean Front Service ACC/FCW Warning Windshield” and the system will have degraded perfor- If the system turns off, and the instrument cluster displays mance. “ACC/FCW Unavailable Service Required” or “Cruise/ FCW Unavailable Service Required”, there may be an The “ACC/FCW Limited Functionality Clean Front Wind- internal system fault or a temporary malfunction that shield”...
Page 303 STARTING AND OPERATING 301 Offset Driving Turns And Bends ACC may not detect a vehicle in the same lane that is offset When driving on a curve with ACC engaged, the system from your direct line of travel, or a vehicle merging in from may decrease the vehicle speed and acceleration for stabil- a side lane.
Page 304 302 STARTING AND OPERATING Using ACC On Hills Lane Changing When driving on hills, ACC may not detect a vehicle in ACC may not detect a vehicle until it is completely in the your lane. Depending on the speed, vehicle load, traffic lane in which you are traveling.
Page 305 STARTING AND OPERATING 303 Narrow Vehicles Stationary Objects And Vehicles Some narrow vehicles traveling near the outer edges of the ACC does not react to stationary objects and stationary lane or edging into the lane are not detected until they have vehicles.
Page 306: General Information
304 STARTING AND OPERATING General Information To change between the different control modes, push the Adaptive Cruise Control (ACC) on/off button which turns The following regulatory statement applies to all Radio the ACC and the Normal (Fixed Speed) Cruise Control off. Frequency (RF) devices equipped in this vehicle: Pushing the Normal (Fixed Speed) Cruise Control on/off This device complies with Part 15 of the FCC Rules and...
Page 307 STARTING AND OPERATING 305 To Set A Desired Speed The speed increment shown is dependant on the speed of U.S. (mph) or Metric (km/h) units: Turn the Normal (Fixed Speed) Cruise Control on. When the vehicle has reached the desired U.S.
Page 308 306 STARTING AND OPERATING • If the button is continually pushed, the set speed will To Decrease Speed continue to decrease in 10 km/h decrements until the When the Normal (Fixed Speed) Cruise Control is set, you button is released. The decrease in set speed is reflected can decrease speed by pushing the SET (-) button.
Page 309: Parksense Rear Park Assist - If Equipped
STARTING AND OPERATING 307 To Turn Off NOTE: • The driver can override the automatic braking function The system will turn off and erase the set speed in memory by pressing the gas pedal, turning ParkSense off via ParkSense switch, or changing the gear while the auto- •...
Page 310: Parksense Sensors
308 STARTING AND OPERATING The automatic braking function is intended to assist the indicating the vehicle speed is too fast. The system will driver in avoiding possible collisions with detected ob- become active again if the vehicle speed is decreased to speeds stacles when backing up in REVERSE gear.
Page 311: Parksense Display
STARTING AND OPERATING 309 ParkSense Display If an obstacle is detected in the left and/or right rear region, the display will show a single arc in the left and/or When the vehicle is in REVERSE and an obstacle has been right rear region and the system will produce a tone.
Page 312 310 STARTING AND OPERATING Slow Tone Slow Tone...
Page 313 STARTING AND OPERATING 311 Fast Tone Fast Tone...
Page 314 312 STARTING AND OPERATING The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone. Continuous Tone...
Page 315 STARTING AND OPERATING 313 The following chart shows the warning alert operation when the system is detecting an obstacle: WARNING ALERTS Rear Greater 79-59 inches 59-47 inches 47-39 inches 39-25 inches 25-12 inches Less than Distance than (200-150 (150-120 (120-100 (100-65 cm) (65-30 cm) 12 inches...
Page 316: Enabling And Disabling Parksense
314 STARTING AND OPERATING Adjustable Chime Volume Settings The ParkSense switch LED will be on when ParkSense is disabled or requires service. The ParkSense switch LED Rear chime volume settings can be selected from the will be off when the system is enabled. If the ParkSense Customer-Programmable Features section of the Uconnect switch is pushed, and the system requires service, the System, refer to “Uconnect Settings”...
Page 317: Cleaning The Parksense System
STARTING AND OPERATING 315 • When you move the gear selector to the REVERSE is clean and clear of snow, ice, mud, dirt or other obstruc- tion and then cycle the ignition. If the message continues to position and ParkSense is turned off, the instrument appear, see an authorized dealer.
Page 318: Parksense Front And Rear Park Assist - If Equipped
316 STARTING AND OPERATING WARNING! CAUTION! • Drivers must be careful when backing up even when • ParkSense is only a parking aid and it is unable to using ParkSense. Always check carefully behind recognize every obstacle, including small obstacles. your vehicle, look behind you, and be sure to check Parking curbs might be temporarily detected or not for pedestrians, animals, other vehicles, obstructions,...
Page 319 STARTING AND OPERATING 317 NOTE: The automatic braking function is intended to assist the driver in avoiding possible collisions with detected ob- • The driver can override the automatic braking function stacles when backing up in REVERSE gear. by pressing the gas pedal, turning ParkSense off via ParkSense switch, or changing the gear while the auto- NOTE: matic brakes are being applied.
Page 320: Parksense Sensors
318 STARTING AND OPERATING A display warning will appear in the instrument cluster ParkSense Warning Display display indicating the vehicle is above ParkSense operating The ParkSense Warning screen will only be displayed if speed. The system will become active again if the vehicle Sound and Display is selected from the Customer Pro- speed is decreased to speeds less than approximately grammable Features section of the Uconnect System.
Page 321: Parksense Display
STARTING AND OPERATING 319 ParkSense Display The system will indicate a detected obstacle by showing a single arc in the left and/or right front or rear regions The warning display will turn on indicating the system based on the object’s distance and location relative to the status when the vehicle is in REVERSE or when the vehicle vehicle.
Page 322 320 STARTING AND OPERATING Slow Tone Slow Tone For Rear Only...
Page 323 STARTING AND OPERATING 321 Fast Tone For Rear Only Fast Tone...
Page 324 322 STARTING AND OPERATING The vehicle is close to the obstacle when the instrument cluster display shows one flashing arc and sounds a continuous tone. Continuous Tone...
Page 325 STARTING AND OPERATING 323 The following chart shows the warning alert operation when the system is detecting an obstacle: WARNING ALERTS FOR REAR Rear Greater 79-59 inches 59-47 inches 47-39 inches 39-25 inches 25-12 inches Less than Distance than (200-150 (150-120 (120-100 (100-65 cm)
Page 326 324 STARTING AND OPERATING WARNING ALERTS FOR FRONT Front Distance Greater than 47 47-39 inches 39-25 inches 25-12 inches Less than (inches/cm) inches (120 cm) (120-100 cm) (100-65 cm) (65-30 cm) 12 inches (30 cm) Audible Alert None None None Fast Continuous Chime...
Page 327: Enabling And Disabling Parksense
STARTING AND OPERATING 325 Enabling And Disabling ParkSense Service The ParkSense Park Assist System ParkSense can be enabled and disabled with the ParkSense During vehicle start up, when the ParkSense System has switch. detected a faulted condition, the instrument cluster will actuate a single chime, once per ignition cycle, and it will When the ParkSense switch is pushed to disable display the PARKSENSE UNAVAILABLE WIPE REAR...
Page 328: Cleaning The Parksense System
326 STARTING AND OPERATING Refer to “Instrument Cluster Display” in “Getting To Know ParkSense System Usage Precautions Your Instrument Panel” for further information. NOTE: If PARKSENSE UNAVAILABLE WIPE REAR SENSORS • Ensure that the front and rear bumper are free of snow, or PARKSENSE UNAVAILABLE WIPE FRONT SEN- ice, mud, dirt and debris to keep the ParkSense system SORS appears in the instrument cluster display make sure...
Page 329 STARTING AND OPERATING 327 obstacle behind or in front of the fascia/bumper, or it WARNING! (Continued) could provide a false indication that an obstacle is • Before using ParkSense, it is strongly recommended behind or in front of the fascia/bumper. that the ball mount and hitch ball assembly is •...
Page 330: Lanesense - If Equipped
328 STARTING AND OPERATING The driver may manually override the haptic warning by CAUTION! (Continued) applying torque into the steering wheel at any time. obstacle is detected. It is recommended that the When only a single lane marking is detected and the driver driver looks over his/her shoulder when using unintentionally drifts across the lane marking (no turn ParkSense.
Page 331: Turning Lanesense On Or Off
STARTING AND OPERATING 329 Turning LaneSense On Or Off To turn the LaneSense system on, push the LaneSense button (LED turns off). A “Lane Sense On” message is The default status of LaneSense is “off”. shown in the instrument cluster display. The LaneSense button is located on the switch panel below the Uconnect display.
Page 332: Lanesense Warning Message
330 STARTING AND OPERATING LaneSense Warning Message detected and the system is ready to provide visual warnings in the instrument cluster display if an unin- The LaneSense system will indicate the current lane drift tentional lane departure occurs. condition through the instrument cluster display. •...
Page 333 STARTING AND OPERATING 331 Left Lane Departure — Both Lanes Detected yellow. At this time torque is applied to the steering wheel in the opposite direction of the lane boundary. • When the LaneSense system is on, the lane lines turn •...
Page 334: Changing Lanesense Status
332 STARTING AND OPERATING • For example: If approaching the left side of the lane the NOTE: steering wheel will turn to the right. • When enabled the system operates above 37 mph (60 km/h) and below 112 mph (180 km/h). •...
Page 335 STARTING AND OPERATING 333 When the vehicle is shifted out of REVERSE (with camera When enabled, active guide lines are overlaid on the image delay turned on), the rear view image with dynamic grid to illustrate the width of the vehicle and its projected lines will be displayed for up to 10 seconds after shifting backup path based on the steering wheel position.
Page 336 334 STARTING AND OPERATING Rear Camera — Viewing At Speed WARNING! When the vehicle is in park, neutral or drive, the Rear View Drivers must be careful when backing up even when Camera can be activated with the “Rear View Camera” using the ParkView Rear Back Up Camera.
Page 337: Refueling The Vehicle
STARTING AND OPERATING 335 REFUELING THE VEHICLE 2. Open the fuel filler door. 1. Push the fuel filler door release switch (located under the headlamp switch). Fuel Filler Door NOTE: In certain cold conditions, ice may prevent the fuel door from opening. If this occurs, lightly push on the fuel Fuel Filler Door Release Switch door to break the ice buildup and re-release the fuel door using the inside release button.
Page 338: Emergency Fuel Filler Door Release
336 STARTING AND OPERATING NOTE: Only the correct size nozzle opens the latches WARNING! allowing the flapper door to open. • Never have any smoking materials lit in or near the 5. Fill the vehicle with fuel – when the fuel nozzle “clicks” vehicle when the fuel door is open or the tank is or shuts off the fuel tank is full.
Page 339: Vehicle Loading
STARTING AND OPERATING 337 2. Push the inboard edge of the left storage bin to the NOTE: If the fuel door does not latch after the manual center, this will pop up the outboard edge. release cable has been activated, the actuator latch should be manually returned to the closed position.
Page 340: Tire Size
338 STARTING AND OPERATING components sometimes specified by purchasers for in- Loading creased durability does not necessarily increase the vehi- The actual total weight and the weight of the front and rear cle’s GVWR. of your vehicle at the ground can best be determined by weighing it when it is loaded and ready for operation.
Page 341: Trailer Towing
STARTING AND OPERATING 339 Gross Vehicle Weight Rating (GVWR) CAUTION! The GVWR is the total allowable weight of your vehicle. Do not load your vehicle any heavier than the GVWR This includes driver, passengers, cargo and tongue weight. or the maximum front and rear GAWR. If you do, parts The total load must be limited so that you do not exceed on your vehicle can break, or it can change the way the GVWR.
Page 342 340 STARTING AND OPERATING Gross Combination Weight Rating (GCWR) Trailer Frontal Area The GCWR is the total allowable weight of your vehicle The frontal area is the maximum height multiplied by the and trailer when weighed in combination. maximum width of the front of a trailer. Gross Axle Weight Rating (GAWR) Trailer Sway Control The GAWR is the maximum capacity of the front and rear...
Page 343 STARTING AND OPERATING 341 Weight-Distributing Hitch WARNING! A weight-distributing system works by applying leverage • An improperly adjusted Weight Distributing Hitch through spring (load) bars. They are typically used for system may reduce handling, stability, braking per- heavier loads to distribute trailer tongue weight to the tow formance, and could result in a collision.
Page 344: Trailer Hitch Classification
342 STARTING AND OPERATING Trailer Hitch Classification The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition. Trailer Hitch Classification Definitions Class Max.
Page 345: Trailer Hitch Receiver Cover Removal - If Equipped
STARTING AND OPERATING 343 NOTE: 1. Turn the two locking retainers located at the bottom of the hitch receiver cover a 1/4 turn counterclockwise and • The trailer tongue weight must be considered as part of pull bottom of the hitch receiver cover outward (to- the combined weight of occupants and cargo, and wards you).
Page 346: Trailer And Tongue Weight
344 STARTING AND OPERATING 2. Pull the bottom of the cover outward (towards you) then Trailer And Tongue Weight downwards to disengage the tabs located at the top of Never exceed the maximum tongue weight stamped on the hitch receiver cover to remove. your bumper or trailer hitch.
Page 347: Towing Requirements
STARTING AND OPERATING 345 NOTE: Remember that everything put into or on the Maintenance” for the proper maintenance intervals. When trailer adds to the load on your vehicle. Also, additional towing a trailer, never exceed the GAWR or GCWR ratings. factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle.
Page 348 346 STARTING AND OPERATING and satisfactory operation of your vehicle. Refer to WARNING! (Continued) “Tires” in “Servicing And Maintenance” for proper tire • Vehicles with trailers should not be parked on a inflation procedures. grade. When parking, apply the parking brake on the •...
Page 349 STARTING AND OPERATING 347 • Trailer brakes are recommended for trailers over Towing Requirements — Trailer Lights And Wiring 1,000 lbs (453 kg) and required for trailers in excess of Whenever you pull a trailer, regardless of the trailer size, 2,000 lbs (907 kg).
Page 350: Towing Tips
348 STARTING AND OPERATING Four-Pin Connector Seven-Pin Connector 1 — Female Pins 4 — Park 1 — Battery 5 — Ground 2 — Male Pin 5 — Left Stop/Turn 2 — Backup Lamps 6 — Left Stop/Turn 3 — Ground 6 —...
Page 351 STARTING AND OPERATING 349 Automatic Transmission Speed Control — If Equipped • Do not use on hilly terrain or with heavy loads. Select the DRIVE range when towing. The transmission controls include a drive strategy to avoid frequent shifting • When using the speed control, if you experience speed when towing.
Page 352: Recreational Towing
350 STARTING AND OPERATING RECREATIONAL TOWING WARNING! Recreational towing is not allowed. Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the front CAUTION! wheels. You could lose control of the vehicle and Towing this vehicle with any of its wheels on the possibly have a collision.
Page 353: Driving Through Water
STARTING AND OPERATING 351 • Maintain sufficient distance between your vehicle and Shallow Standing Water the vehicle in front of you to avoid a collision in a Although your vehicle is capable of driving through shal- sudden stop. low standing water, consider the following Cautions and Warnings before doing so.
Page 354 352 STARTING AND OPERATING CAUTION! • Always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle. • Determine the condition of the road or the path that is under water and if there are any obstacles in the way before driving through the standing water.
Page 355 IN CASE OF EMERGENCY CONTENTS ▫ Preparations For Jacking ....376 HAZARD WARNING FLASHERS ... .354 ▫...
Page 356: Hazard Warning Flashers
354 IN CASE OF EMERGENCY HAZARD WARNING FLASHERS ASSIST AND SOS MIRROR — IF EQUIPPED The Hazard Warning flasher switch is located on the switch bank just above the climate controls. Push the switch to turn on the Hazard Warning flasher.
Page 357 IN CASE OF EMERGENCY 355 ASSIST Call WARNING! The ASSIST Button is used to automatically connect you to ALWAYS obey traffic laws and pay attention to the any one of the following support centers: road. ALWAYS drive safely with your hands on the •...
Page 358 356 IN CASE OF EMERGENCY 2. The LED light located between the ASSIST and SOS NOTE: buttons on the Rearview Mirror will turn green once a • Your vehicle may be transmitting data as authorized connection to a SOS operator has been made. by the subscriber.
Page 359 IN CASE OF EMERGENCY 357 WARNING! (Continued) WARNING! (Continued) • Modifications to any part of the SOS Call system Emergency Services Agent. All occupants should exit the vehicle immediately and move to a safe location. could cause the air bag system to fail when you need •...
Page 360 358 IN CASE OF EMERGENCY • The vehicle battery loses power or becomes discon- WARNING! nected during a vehicle crash. • Ignoring the Rearview Mirror light could mean you • LTE (voice/data) or 4G (data) network and/or Global will not have SOS Call services. If the Rearview Positioning Satellite signals are unavailable or ob- Mirror light is illuminated, have your authorized structed.
Page 361 IN CASE OF EMERGENCY 359 NOTE: General Information • Your vehicle may be transmitting data as authorized by This device complies with Part 15 of the FCC Rules. the subscriber. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) •...
Page 362: Bulb Replacement
360 IN CASE OF EMERGENCY BULB REPLACEMENT Replacement Bulbs Interior Bulbs Bulb Number Glove Compartment Lamp Grab Handle Lamp L002825W5W Overhead Console Reading Lamps VT4976 Visor Vanity Lamp V26377 Rear Cargo Lamp 214–2 Underpanel Courtesy Lamps Instrument Cluster (General Illumination) Telltale/Hazard Lamp Exterior Bulbs Bulb Number...
Page 363: Bulb Replacement
IN CASE OF EMERGENCY 361 Bulb Number Front Park/Turn Signal Lamps (Base) 3157NAK Front Turn Signal Lamps (Uplevel & Premium) 3157NAK Front Park Lamp/Daytime Running Lamp (Uplevel & LED (Serviced At Authorized Dealer) Premium) Front Side Marker Lamps LED (Serviced At Authorized Dealer) Front Fog Lamps Rear Tail Lamps/Sidemarker Lamps LED (Serviced At Authorized Dealer)
Page 364 362 IN CASE OF EMERGENCY 5. Firmly grasp the low/high beam bulb and connector WARNING! assembly and rotate counterclockwise to remove from housing. A transient high voltage occurs at the bulb sockets of High Intensity Discharge (HID) headlamps when the 6.
Page 365 IN CASE OF EMERGENCY 363 3. Disconnect the electrical connector and replace the bulb. CAUTION! (Continued) bulb comes in contact with any oily surface, clean the CAUTION! bulb with rubbing alcohol. • Always use the correct bulb size and type for replace- Do not touch the new bulb with your fingers.
Page 366: Fuses
364 IN CASE OF EMERGENCY Center High-Mounted Stop Lamp (CHMSL) WARNING! (Continued) The center high-mounted stop lamp is an LED assembly. • If the replaced fuse blows again, contact an autho- See your authorized dealer for replacement. rized dealer. • If a general protection fuse for safety systems (air Rear License Lamp bag system, braking system), power unit systems The rear license lamps are LEDs.
Page 367: Underhood Fuses
IN CASE OF EMERGENCY 365 Also, please be aware that when using power outlets for Underhood Fuses extended periods of time with the engine off may result in The Power Distribution Center is located in the engine vehicle battery discharge. compartment near the battery.
Page 368 366 IN CASE OF EMERGENCY Cavity Cartridge Fuse Micro Fuse Description 60 Amp Yellow – Radiator Fan 40 Amp Green – Compressor for Air Suspension — If Equipped 40 Amp Green – Anti-lock Brakes/Electronic Stability Control Pump 30 Amp Pink –...
Page 369 IN CASE OF EMERGENCY 367 Cavity Cartridge Fuse Micro Fuse Description 30 Amp Pink – Driver Door Module 30 Amp Pink – Front Wipers 30 Amp Pink – Anti-lock Brakes/Stability Control Module/ Valves 20 Amp Blue – Trailer Tow Backup Lights — If Equipped 20 Amp Blue –...
Page 370 368 IN CASE OF EMERGENCY Cavity Cartridge Fuse Micro Fuse Description – 20 Amp Yellow Air Suspension Control Module/ Slip Differential - If Equipped – 15 Amp Blue Ignition Node Module/Keyless Ignition/ Steering Column Lock – 20 Amp Yellow Trailer Tow – Left Turn/Stop Lights — If Equipped –...
Page 371 IN CASE OF EMERGENCY 369 Cavity Cartridge Fuse Micro Fuse Description – 15 Amp Blue Spotlight Feed — If Equipped – 20 Amp Yellow Fuel Pump Motor – 30 Amp Green Audio Amplifier – 10 Amp Red PCM — If Equipped –...
Page 372 370 IN CASE OF EMERGENCY Cavity Cartridge Fuse Micro Fuse Description – 10 Amp Red Air Suspension — If Equipped/ Steering Column Control Module – 15 Amp Blue Instrument Panel Cluster F90/F91 – 20 Amp Yellow Power Outlet (Rear seats) Selectable –...
Page 373: Jacking And Tire Changing
IN CASE OF EMERGENCY 371 Cavity Cartridge Fuse Micro Fuse Description F104 – 20 Amp Yellow Power Outlets (Instrument Panel/ Center Console) JACKING AND TIRE CHANGING CAUTION! • When installing the power distribution center cover, WARNING! it is important to ensure the cover is properly posi- •...
Page 374: Run Flat Tires
372 IN CASE OF EMERGENCY Run Flat Tires Jack Location This vehicle is equipped with “run flat” tires. Run flat tires The scissor-type jack and tire changing tools are located in allow the vehicle to be driven approximately 50 miles rear cargo area, below the load floor.
Page 375: Spare Tire Stowage
IN CASE OF EMERGENCY 373 Rotate the plastic thumb screw on the end of the jack to loosen the jack and remove from the bracket. Spare Tire Location CAUTION! Thumb Screw Location The winch mechanism is designed for use with the Spare Tire Stowage jack wrench extension tool only.
Page 376 374 IN CASE OF EMERGENCY 3. Fit the jack handle extension over the drive nut. Use the 4. Slide the tire out from under the vehicle and rotate it lug wrench handle and extension to completely lower vertically behind the rear bumper. the spare tire.
Page 377 IN CASE OF EMERGENCY 375 6. Slide the metal stamping up the steel extension tube and 7. Pinch the three short and two long tubes to remove the winch cable. Rotate the metal stamping and push it protective plate from the steel spare wheel. through the hole in the plastic plate and wheel.
Page 378: Preparations For Jacking
376 IN CASE OF EMERGENCY Preparations For Jacking NOTE: Passengers should not remain in the vehicle when the vehicle is being jacked. 1. Park the vehicle on a firm, level surface as far from the edge of the roadway as possible. Avoid icy or slippery Jacking Instructions areas.
Page 379 IN CASE OF EMERGENCY 377 WARNING! (Continued) CAUTION! • Only use the jack in the positions indicated and for Do not attempt to raise the vehicle by jacking on lifting this vehicle during a tire change. locations other than those indicated in the Jacking •...
Page 380 378 IN CASE OF EMERGENCY 3. For the front tire, place the jack on the body flange just behind the front tire. Do not raise the vehicle until you are sure the jack is fully engaged. Rear Jacking Location 5. Raise the vehicle by turning the jack screw clockwise. Raise the vehicle just enough to remove the flat tire.
Page 381 IN CASE OF EMERGENCY 379 6. Remove the lug nuts and wheel. CAUTION! 7. Install the spare wheel/tire on the vehicle and install the Be sure to mount the spare tire with the valve stem lug nuts with the cone-shaped end toward the wheel. facing outward.
Page 382 380 IN CASE OF EMERGENCY 10. Push out the small center cap using the jack tool from 11. Insert the two long tubes on the plastic protective plate inside the aluminum road wheel and position the in the lug holes of the road wheel. Push the end of the wheel behind the rear bumper with the protective plate winch’s cable, spring, steel sleeve and stamped cone facing outward.
Page 383 IN CASE OF EMERGENCY 381 12. Slide the road wheel on the ground using the protec- CAUTION! tive plate until it is directly under the winch and between the rear bumper and exhaust system heat The winch mechanism is designed for use with the shields.
Page 384: Road Tire Installation
382 IN CASE OF EMERGENCY 5. After 25 miles (40 km), check the lug nut torque with a WARNING! torque wrench to ensure that all lug nuts are properly seated against the wheel. A loose tire or jack thrown forward in a collision or hard stop, could endanger the occupants of the vehicle.
Page 385: Preparations For Jump Start
IN CASE OF EMERGENCY 383 Preparations For Jump Start WARNING! The battery in your vehicle is located under the passenger’s • Take care to avoid the radiator cooling fan whenever front seat. There are remote terminals located under the the hood is raised. It can start anytime the ignition hood to assist in jump starting.
Page 386: Jump Starting Procedure
384 IN CASE OF EMERGENCY 4. If using another vehicle to jump start the battery, park Connecting The Jumper Cables the vehicle within the jumper cables reach, apply the 1. Connect the positive (+) end of the jumper cable to the parking brake and make sure the ignition is OFF.
Page 387: If Your Engine Overheats
IN CASE OF EMERGENCY 385 CAUTION! CAUTION! Accessories plugged into the vehicle power outlets Do not run the booster vehicle engine above 2000 rpm draw power from the vehicle’s battery, even when not since it provides no charging benefit, wastes fuel and in use (i.e., cellular devices, etc.).
Page 388: Manual Park Release
386 IN CASE OF EMERGENCY high. This allows the heater core to act as a supplement MANUAL PARK RELEASE to the radiator and aids in removing heat from the engine cooling system. WARNING! Always secure your vehicle by fully applying the WARNING! parking brake before activating the Manual Park Re- You or others can be badly burned by hot engine...
Page 389 IN CASE OF EMERGENCY 387 2. Open the center console and locate the Manual Park 3. Press and maintain firm pressure on the brake pedal. Release cover, remove it by snapping the cover away 4. Using a screwdriver or similar tool, push the metal latch from the console hinges.
Page 390 388 IN CASE OF EMERGENCY 5. While the metal latch is in the open position, pull To Disengage The Manual Park Release Lever: upward on the tether strap until the lever clicks and 1. To disengage the Manual Park Release, apply tension latches in the released position.
Page 391: Freeing A Stuck Vehicle
IN CASE OF EMERGENCY 389 2. Once the tension has been released and the lever has FREEING A STUCK VEHICLE been unlocked, be sure it is stowed properly and locks If your vehicle becomes stuck in mud, sand or snow, it can into position.
Page 392: Towing A Disabled Vehicle
390 IN CASE OF EMERGENCY WARNING! CAUTION! (Continued) • Revving the engine or spinning the wheels too fast Fast spinning tires can be dangerous. Forces generated may lead to transmission overheating and failure. It by excessive wheel speeds may cause damage, or even can also damage the tires.
Page 393: Enhanced Accident Response System (Ears)
IN CASE OF EMERGENCY 391 ENHANCED ACCIDENT RESPONSE SYSTEM EVENT DATA RECORDER (EDR) (EARS) This vehicle is equipped with an Event Data Recorder This vehicle is equipped with an Enhanced Accident (EDR). The main purpose of an EDR is to record data that Response System.
Page 395 SERVICING AND MAINTENANCE CONTENTS ▫ Windshield Wiper Blades ....411 SCHEDULED SERVICING ....395 ▫...
Page 396 394 SERVICING AND MAINTENANCE ▫ Tire Chains (Traction Devices) ... . .447 BODYWORK ......451 ▫...
Page 397: Scheduled Servicing
SERVICING AND MAINTENANCE 395 SCHEDULED SERVICING NOTE: • The oil change indicator message will not monitor the The Scheduled Maintenance services listed in this manual time since the last oil change. Change your vehicle’s oil must be done at the times or mileages specified to protect if it has been six months since your last oil change, even your vehicle warranty and ensure the best vehicle perfor- if the oil change indicator message is NOT illuminated.
Page 398 396 SERVICING AND MAINTENANCE At Each Stop For Fuel At Each Oil Change • Check the engine oil level. Refer to “Engine Compart- • Change the engine oil filter. ment” in this section for further information. • Inspect the brake hoses and lines. •...
Page 399: Maintenance Plan
SERVICING AND MAINTENANCE 397 Maintenance Plan Miles: Or Months: 96 102 108 114 120 126 132 138 144 150 Or Kilometers: Change the engine oil and engine oil filter. Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before scheduled maintenance.
Page 400 398 SERVICING AND MAINTENANCE Miles: Or Months: 96 102 108 114 120 126 132 138 144 150 Or Kilometers: Inspect the front and rear axle fluid. Change if using your ve- hicle for any of the following: police, taxi, fleet, sustained high speed driving, off-road or frequent trailer towing.
Page 401 SERVICING AND MAINTENANCE 399 WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.
Page 402: Engine Compartment
400 SERVICING AND MAINTENANCE ENGINE COMPARTMENT 6.4L Engine 1 — Remote Jump Start Positive Terminal 6 — Washer Fluid Reservoir 2 — Power Distribution Center (Fuses) 7 — Engine Oil Dipstick 3 — Engine Oil Fill 8 — Coolant Pressure Cap (Radiator) 4 —...
Page 403: Checking Oil Level
SERVICING AND MAINTENANCE 401 Checking Oil Level The fluid reservoir for the windshield washers and the rear window washer is shared. The fluid reservoir is located in To assure proper lubrication of your vehicle’s engine, the the engine compartment, be sure to check the fluid level at engine oil must be maintained at the correct level.
Page 404: Dealer Service
402 SERVICING AND MAINTENANCE WARNING! CAUTION! • Battery fluid is a corrosive acid solution and can • It is essential when replacing the cables on the burn or even blind you. Do not allow battery fluid to battery that the positive cable is attached to the contact your eyes, skin, or clothing.
Page 405: Engine Oil
SERVICING AND MAINTENANCE 403 The manufacturer recommends the use of Pennzoil Ultra WARNING! 0W-40 engine or equivalent Mopar oil meeting the FCA Material Standard MS-12633 for use in all operating tem- You can be badly injured working on or around a peratures.
Page 406 404 SERVICING AND MAINTENANCE American Petroleum Institute (API) Engine Oil engine oil filler cap location, refer to “Engine Compart- Identification Symbol ment” in this section for further information. Synthetic Engine Oils This symbol means that the oil has You may use synthetic engine oils provided the recom- been certified by the American Pe- mended oil quality requirements are met, and the recom- troleum Institute (API).
Page 407: Engine Oil Filter
SERVICING AND MAINTENANCE 405 Engine Oil Filter WARNING! (Continued) The engine oil filter should be replaced with a new filter at near the engine compartment before starting the ve- every engine oil change. hicle with the air induction system (air cleaner, hoses, etc.) removed.
Page 408 406 SERVICING AND MAINTENANCE Refrigerant Recovery And Recycling R-134a — WARNING! (Continued) If Equipped system. Some unapproved refrigerants are flam- R-134a Air Conditioning Refrigerant is a hydrofluoro- mable and can explode, injuring you. Other unap- carbon (HFC) that is an ozone-friendly substance. The proved refrigerants or lubricants can cause the sys- manufacturer recommends that air conditioning service be tem to fail, requiring costly repairs.
Page 409 SERVICING AND MAINTENANCE 407 Air Conditioning Filter Replacement (A/C Air Filter) Refer to “Scheduled Servicing” in this section for the proper maintenance intervals. WARNING! Do not remove the cabin air filter while the vehicle is running, or while the ignition is in the ACC or ON/ RUN mode.
Page 410 408 SERVICING AND MAINTENANCE NOTE: When disengaging the glove compartment door 5. Remove the filter cover by disengaging the retaining tab from its hinges, there will be some resistance. and mid way snap that secures the filter cover to the HVAC housing.
Page 411: Accessory Drive Belt Inspection
SERVICING AND MAINTENANCE 409 7. Install the A/C air filter with the arrow on the filter Accessory Drive Belt Inspection pointing toward the floor. When installing the filter cover, make sure the retaining tabs fully engage the WARNING! cover. • Do not attempt to inspect an accessory drive belt with vehicle running.
Page 412: Body Lubrication
410 SERVICING AND MAINTENANCE • Noise (objectionable squeal, squeak, or rumble is heard or felt while drive belt is in operation) Some conditions can be caused by a faulty component such as a belt pulley. Belt pulleys should be carefully inspected for damage and proper alignment.
Page 413: Windshield Wiper Blades
SERVICING AND MAINTENANCE 411 The external lock cylinders should be lubricated twice a The wiper blades and wiper arms should be inspected year, preferably in the Fall and Spring. Apply a small periodically, not just when wiper performance problems amount of a high quality lubricant, such as Mopar Lock are experienced.
Page 414 412 SERVICING AND MAINTENANCE 1. Lift the wiper arm to raise the wiper blade off of the 2. To disengage the wiper blade from the wiper arm, flip glass, until the wiper arm is in the full up position. up the release tab on the wiper blade and while holding the wiper arm with one hand, slide the wiper blade down towards the base of the wiper arm.
Page 415 SERVICING AND MAINTENANCE 413 3. With the wiper blade disengaged, remove the wiper Installing The Front Wipers blade from the wiper arm by holding the wiper arm 1. Lift the wiper arm off of the glass, until the wiper arm is with one hand and separating the wiper blade from the in the full up position.
Page 416 414 SERVICING AND MAINTENANCE NOTE: The rear wiper arm cannot be fully raised off the glass unless the wiper arm pivot cap is unsnapped first. Attempting to fully raise the rear wiper arm without unsnapping the wiper arm pivot cap may damage the vehicle.
Page 417: Exhaust System
SERVICING AND MAINTENANCE 415 NOTE: Resistance will be accompanied by an audible Installing The Rear Wiper snap. 1. Lift the rear wiper arm pivot cap away from the glass to 4. Still grasping the bottom end of the wiper blade, move allow the rear wiper blade to be raised off of the glass.
Page 418 416 SERVICING AND MAINTENANCE have an authorized technician inspect the complete ex- CAUTION! haust system and adjacent body areas for broken, dam- • The catalytic converter requires the use of unleaded aged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep into fuel only.
Page 419: Cooling System
SERVICING AND MAINTENANCE 417 In unusual situations involving grossly malfunctioning WARNING! (Continued) engine operation, a scorching odor may suggest severe and do not open the hood until the radiator has had time abnormal catalyst overheating. If this occurs, stop the to cool.
Page 420 418 SERVICING AND MAINTENANCE Check the engine cooling system hoses for brittle rubber, NOTE: cracking, tears, cuts, and tightness of the connection at the • Mixing of engine coolant (antifreeze) other than speci- coolant recovery bottle and radiator. Inspect the entire fied Organic Additive Technology (OAT) engine coolant system for leaks.
Page 421 SERVICING AND MAINTENANCE 419 • Some vehicles require special tools to add coolant prop- • Mix a minimum solution of 50% OAT engine coolant erly. Failure to fill these systems properly could lead to that meets the requirements of FCA Material Standard severe internal engine damage.
Page 422 420 SERVICING AND MAINTENANCE • Mixing engine coolant (antifreeze) types is not recom- WARNING! (Continued) mended and can result in cooling system damage. If • Do not use a pressure cap other than the one speci- HOAT and OAT coolant are mixed in an emergency, fied for your vehicle.
Page 423 SERVICING AND MAINTENANCE 421 • If frequent engine coolant (antifreeze) additions are When additional coolant (antifreeze) is needed to maintain the proper level, it should be added to the coolant bottle. required, the cooling system should be pressure tested Do not overfill. for leaks.
Page 424: Brake System
422 SERVICING AND MAINTENANCE Brake System Refer to “Fluids And Lubricants” in “Technical Specifica- tions” for further information. In order to assure brake system performance, all brake system components should be inspected periodically. Refer WARNING! to the “Maintenance Plan” in this section for the proper maintenance intervals.
Page 425: Automatic Transmission
SERVICING AND MAINTENANCE 423 WARNING! (Continued) CAUTION! brake fluid to catch fire. Brake fluid can also damage Using a transmission fluid other than the manufactur- painted and vinyl surfaces, care should be taken to er’s recommended fluid may cause deterioration in avoid its contact with these surfaces.
Page 426: Front/Rear Axle Fluid
424 SERVICING AND MAINTENANCE Fluid Level Check Routine fluid and filter changes are not required. However, change the fluid and filter if the fluid becomes contami- The fluid level is preset at the factory and does not require nated (with water, etc.), or if the transmission is disas- adjustment under normal operating conditions.
Page 427: Transfer Case
SERVICING AND MAINTENANCE 425 Rear Axle Fluid Level Check Adding Fluid The rear axle oil level needs to be no lower than 1/8 inch Add fluid at the filler hole, until it runs out of the hole, (3 mm) below the bottom of the fill hole. when the vehicle is in a level position.
Page 428: Tires
426 SERVICING AND MAINTENANCE TIRES Tire Markings Tire Safety Information Tire safety information will cover aspects of the following information: Tire Markings, Tire Identification Numbers, Tire Terminology and Definitions, Tire Pressures, and Tire Loading. Tire Markings 1 — U.S. DOT Safety Standards Code (TIN) 2 —...
Page 429 SERVICING AND MAINTENANCE 427 • Temporary spare tires are designed for temporary emer- NOTE: gency use only. Temporary high pressure compact spare • P (Passenger) — Metric tire sizing is based on U.S. tires have the letter “T” or “S” molded into the sidewall design standards.
Page 430 428 SERVICING AND MAINTENANCE Tire Sizing Chart EXAMPLE: Example Size Designation: P215/65R15XL 95H, 215/65R15 96H, LT235/85R16C, T145/80D18 103M, 31x10.5 R15 LT P = Passenger car tire size based on U.S. design standards, or ..blank..= Passenger car tire based on European design standards, or LT = Light truck tire based on U.S.
Page 431 SERVICING AND MAINTENANCE 429 EXAMPLE: Service Description: 95 = Load Index – A numerical code associated with the maximum load a tire can carry H = Speed Symbol – A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under cer- tain operating conditions –...
Page 432 430 SERVICING AND MAINTENANCE EXAMPLE: DOT MA L9 ABCD 0301 DOT = Department of Transportation – This symbol certifies that the tire is in compliance with the U.S. Department of Transportation tire safety standards and is approved for highway use MA = Code representing the tire manufacturing location (two digits) L9 = Code representing the tire size (two digits) ABCD = Code used by the tire manufacturer (one to four digits)
Page 433 SERVICING AND MAINTENANCE 431 Tire Terminology And Definitions Term Definition B-Pillar The vehicle B-Pillar is the structural member of the body located be- hind the front door. Cold Tire Inflation Pressure Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after sitting for a minimum of three hours.
Page 434 432 SERVICING AND MAINTENANCE Tire Loading And Tire Pressure NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door. Check the inflation pressure of each tire, including the spare tire (if equipped), at least monthly and inflate to the recommended pressure for your vehicle.
Page 435 SERVICING AND MAINTENANCE 433 Tire And Loading Information Placard Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size, and cold tire inflation pressures specified on the Tire and Loading Information placard in “Vehicle Loading”...
Page 436 434 SERVICING AND MAINTENANCE Steps For Determining Correct Load Limit— Metric Example For Load Limit (1) Locate the statement “The combined weight of For example, if “XXX” amount equals 635 kg and there will occupants and cargo should never exceed XXX kg or be five 68 kg passengers in your vehicle, the amount of XXX lbs.”...
Page 437 SERVICING AND MAINTENANCE 435 WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the rec- ommended load capacity for your vehicle. Never over- load them.
Page 438: Tires - General Information
436 SERVICING AND MAINTENANCE Tires — General Information WARNING! (Continued) Tire Pressure handling and can fail suddenly, resulting in loss of vehicle control. Proper tire inflation pressure is essential to the safe and • Unequal tire pressures can cause steering problems. satisfactory operation of your vehicle.
Page 439 SERVICING AND MAINTENANCE 437 Tread Wear CAUTION! Improper cold tire inflation pressures can cause abnormal After inspecting or adjusting the tire pressure, always wear patterns and reduced tread life, resulting in the need reinstall the valve stem cap. This will prevent moisture for earlier tire replacement.
Page 440 438 SERVICING AND MAINTENANCE pressure should be increased by 3 psi (21 kPa), which Radial Ply Tires equals 1 psi (7 kPa) for every 12°F (7°C) for this outside temperature condition. WARNING! Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) Combining radial ply tires with other types of tires on during operation.
Page 441 SERVICING AND MAINTENANCE 439 Run Flat Tires — If Equipped Tire Spinning Run Flat tires allow you the capability to drive 50 miles When stuck in mud, sand, snow, or ice conditions, do not (80 km) at 50 mph (80 km/h) after a rapid loss of inflation spin your vehicle’s wheels above 30 mph (48 km/h) or for pressure.
Page 442 440 SERVICING AND MAINTENANCE Tread Wear Indicators worn to the tread wear indicators, the tire should be replaced. Refer to “Replacement Tires” in this section for Tread wear indicators are in the original equipment tires to further information. help you in determining when your tires should be re- placed.
Page 443 SERVICING AND MAINTENANCE 441 It is recommended to replace the two front tires or two rear WARNING! (Continued) tires as a pair. Replacing just one tire can seriously affect You could lose control and have a collision resulting in your vehicle’s handling. If you ever replace a wheel, make serious injury or death.
Page 444: Tire Types
442 SERVICING AND MAINTENANCE tire sidewall. Use all season tires only in sets of four; failure WARNING! (Continued) to do so may adversely affect the safety and handling of • Never use a tire with a smaller load index or capacity, your vehicle.
Page 445: Spare Tires - If Equipped
SERVICING AND MAINTENANCE 443 Snow Tires Spare Tires — If Equipped Some areas of the country require the use of snow tires NOTE: For vehicles equipped with Tire Service Kit instead during the Winter. Snow tires can be identified by a of a spare tire, please refer to “Tire Service Kit”...
Page 446 444 SERVICING AND MAINTENANCE Compact Spare Tire — If Equipped WARNING! The compact spare is for temporary emergency use only. Compact and collapsible spares are for temporary You can identify if your vehicle is equipped with a compact emergency use only. With these spares, do not drive spare by looking at the spare tire description on the Tire more than 50 mph (80 km/h).
Page 447 SERVICING AND MAINTENANCE 445 Do not install a wheel cover or attempt to mount a Limited Use Spare — If Equipped conventional tire on the collapsible spare wheel, since the The limited use spare tire is for temporary emergency use wheel is designed specifically for the collapsible spare tire.
Page 448: Wheel And Wheel Trim Care
446 SERVICING AND MAINTENANCE Wheel And Wheel Trim Care When cleaning extremely dirty wheels including excessive brake dust, care must be taken in the selection of tire and All wheels and wheel trim, especially aluminum and chrome wheel cleaning chemicals and equipment to prevent dam- plated wheels, should be cleaned regularly using mild (neutral age to the wheels.
Page 449: Tire Chains (Traction Devices)
SERVICING AND MAINTENANCE 447 Dark Vapor Chrome, Black Satin Chrome, or Low Gloss Tire Rotation Recommendations Clear Coat Wheels The tires on the front and rear of your vehicle operate at different loads and perform different steering, handling, CAUTION! and braking functions. For these reasons, they wear at unequal rates.
Page 450: Department Of Transportation Uniform Tire Quality Grades
448 SERVICING AND MAINTENANCE The suggested rotation method is the “rearward-cross” Treadwear shown in the following diagram. The Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half times as well on the government course as a tire graded 100.
Page 451: Temperature Grades
SERVICING AND MAINTENANCE 449 WARNING! (Continued) WARNING! (Continued) include acceleration, cornering, hydroplaning, or Excessive speed, under-inflation, or excessive load- peak traction characteristics. ing, either separately or in combination, can cause heat buildup and possible tire failure. Temperature Grades STORING THE VEHICLE The Temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of If the vehicle should remain stationary for more than a...
Page 452: Battery Storage Mode
450 SERVICING AND MAINTENANCE • Clean and protect polished metal parts by applying CAUTION! protective waxes. Before removal of the positive and negative terminals • Apply talcum powder to the front and rear wiper blades to the battery, wait at least a minute with ignition and leave raised from the glass.
Page 453: Bodywork
SERVICING AND MAINTENANCE 451 • Salt in the air near seacoast localities. BODYWORK • Atmospheric fallout/industrial pollutants. Protection From Atmospheric Agents Vehicle body care requirements vary according to geo- Body And Underbody Maintenance graphic locations and usage. Chemicals that make roads Cleaning Headlights passable in snow and ice and those that are sprayed on Your vehicle is equipped with plastic headlights and fog...
Page 454 452 SERVICING AND MAINTENANCE • If insects, tar, or other similar deposits have accumulated • It is important that the drain holes in the lower edges of on your vehicle, use Mopar Super Kleen Bug and Tar the doors, rocker panels, and trunk be kept clear and Remover to remove.
Page 455: Interiors
SERVICING AND MAINTENANCE 453 INTERIORS WARNING! Seats And Fabric Parts A frayed or torn belt could rip apart in a collision and Use Mopar Total Clean to clean fabric upholstery and leave you with no protection. Inspect the belt system carpeting.
Page 456: Leather Parts
454 SERVICING AND MAINTENANCE Cleaning Plastic Instrument Cluster Lenses NOTE: If equipped with light colored leather, it tends to show any foreign material, dirt, and fabric dye transfer The lenses in front of the instruments in this vehicle are more so than darker colors. The leather is designed for easy molded in clear plastic.
Page 457 TECHNICAL SPECIFICATIONS CONTENTS ▫ Do Not Use E-85 In Non-Flex Fuel Vehicles ..460 IDENTIFICATION DATA....456 ▫ Vehicle Identification Number ... . .456 ▫...
Page 458: Identification Data
456 TECHNICAL SPECIFICATIONS IDENTIFICATION DATA Vehicle Identification Number The Vehicle Identification Number (VIN) is found on a label located on the left front corner of the instrument panel pad, visible from outside of the vehicle through the wind- shield. This number also is stamped on the right front floor, behind the right front seat.
Page 459: Brake System
TECHNICAL SPECIFICATIONS 457 In the event power assist is lost for any reason (i.e., repeated brake applications with the engine off) the brakes will still function. However, the effort required to brake the vehicle will be much greater than that required with the power system operating.
Page 460 458 TECHNICAL SPECIFICATIONS Inspect the wheel mounting surface prior to mounting the After 25 miles (40 km), check the lug nut/bolt torque to be tire and remove any corrosion or loose particles. sure that all the lug nuts/bolts are properly seated against the wheel.
Page 461: Fuel Requirements
TECHNICAL SPECIFICATIONS 459 FUEL REQUIREMENTS Reformulated Gasoline Many areas of the country require the use of cleaner 6.4L Engine burning gasoline referred to as “Reformulated Gasoline”. Do not use E-85 flex fuel or ethanol blends greater than Reformulated gasoline contains oxygenates and are specifi- 15% in this engine.
Page 462: Gasoline/Oxygenate Blends
460 TECHNICAL SPECIFICATIONS Indiscriminate use of fuel system cleaning agents should be Problems that result from using gasoline containing more avoided. Many of these materials intended for gum and than 15% ethanol (E-15) or gasoline containing methanol varnish removal may contain active solvents or similar are not the responsibility of the manufacturer and may ingredients.
Page 463: Cng And Lp Fuel System Modifications
TECHNICAL SPECIFICATIONS 461 CNG And LP Fuel System Modifications Fuel System Cautions Modifications that allow the engine to run on compressed CAUTION! natural gas (CNG) or liquid propane (LP) may result in damage to the engine, emissions, and fuel system compo- Follow these guidelines to maintain your vehicle’s nents.
Page 464: Carbon Monoxide Warnings
462 TECHNICAL SPECIFICATIONS Carbon Monoxide Warnings WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon mon- oxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill.
Page 465: Fluid Capacities
TECHNICAL SPECIFICATIONS 463 FLUID CAPACITIES U.S. Metric Fuel (Approximate) 24.6 Gallons 93.0 Liters Engine Oil With Filter 6.4 Liter Engine (SAE 0W-40, Synthetic API Certified, MS-12633) 7 Quarts 6.6 Liters Cooling System* 6.4 Liter Engine (Mopar Antifreeze/Engine Coolant 10 Year/150,000 16 Quarts 15.5 Liters Mile Formula that meets the requirements of FCA Material Standard...
Page 466: Fluids And Lubricants
464 TECHNICAL SPECIFICATIONS FLUIDS AND LUBRICANTS Engine Component Fluid, Lubricant or Genuine Part Engine Coolant We recommend you use Mopar Antifreeze/Coolant 10 Year/150,000 Mile Formula OAT (Organic Additive Technology) that meets the requirements of FCA Material Standard MS.90032. Engine Oil For best performance and maximum protection under all types of operating conditions, the manufacturer only rec- ommends full synthetic engine oils that meet the American...
Page 467: Chassis
TECHNICAL SPECIFICATIONS 465 Chassis Component Fluid, Lubricant, or Genuine Part Automatic Transmission Use only Mopar ZF 8&9 Speed ATF Automatic Transmission Fluid or equivalent. Failure to use the correct fluid may affect the function or performance of your transmission. Transfer Case – Single-Speed (Selec-Track) We recommend you use Mopar ATF+4 Automatic Transmission Fluid.
Page 469 MULTIMEDIA CONTENTS UCONNECT SYSTEMS ....470 SRT DRIVE MODES ..... .503 ▫...
Page 470 468 MULTIMEDIA ▫ Blu-ray Disc Player Remote Control — STEERING WHEEL AUDIO CONTROLS — IF EQUIPPED ......516 If Equipped .
Page 471 MULTIMEDIA ▫ Navigation (4C NAV) ....542 ▫ Android Auto — If Equipped ....545 ▫...
Page 472: Uconnect Systems
470 MULTIMEDIA UCONNECT SYSTEMS For detailed information about your Uconnect system, refer to your Uconnect Owner’s Manual Supplement. NOTE: Uconnect screen images are for illustration pur- poses only and may not reflect exact software for your vehicle. DRAG & DROP MENU BAR The Uconnect features and services in the main menu bar are easily changed for your convenience.
Page 473: Cybersecurity
MULTIMEDIA CYBERSECURITY WARNING! Your vehicle may be a connected vehicle and may be • It is not possible to know or to predict all of the equipped with both wired and wireless networks. These possible outcomes if your vehicle’s systems are networks allow your vehicle to send and receive informa- breached.
Page 474: Uconnect Settings
472 MULTIMEDIA NOTE: UCONNECT SETTINGS • FCA US LLC or your dealer may contact you directly The Uconnect system uses a combination of buttons on the regarding software updates. touchscreen and buttons on the faceplate located on the center of the instrument panel that allow you to access and •...
Page 475: Customer Programmable Features - Uconnect 4C/4C Nav Settings
MULTIMEDIA Customer Programmable Features — When making a selection, press the button on the touch- screen to enter the desired mode. Once in the desired Uconnect 4C/4C NAV Settings mode, press and release the preferred setting “option” until Press the “Apps ”...
Page 476 474 MULTIMEDIA Display After pressing the “Display” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Display Mode Manual Auto Display Brightness With Headlights ON NOTE: To make changes to the Display Brightness with Headlights ON setting, the headlights must be on and the interior dimmer switch must not be in the party or parade positions.
Page 477 MULTIMEDIA Setting Name Selectable Options Set Language NOTE: When the “Set Language” feature is selected, you may select one of multiple languages (English / Français / Español) for all display nomenclature, including the trip functions and the navigation system (if equipped). Press the “Set Language”...
Page 478 476 MULTIMEDIA Units After pressing the “Units” button on the touchscreen, you may select each unit of measure independently displayed in the instrument cluster display, and navigation system (if equipped). The following selectable units of measure are listed below: Setting Name Selectable Options Units Metric...
Page 479 MULTIMEDIA Clock After pressing the “Clock” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Sync Time With GPS Set Time Hours NOTE: The “Set Time Hours” feature will allow you to adjust the hours. The “Sync time with GPS” button on the touch- screen must be unchecked.
Page 480 478 MULTIMEDIA Safety & Driving Assistance After pressing the “Safety/Assistance” button on the touchscreen, the following settings will be available: Setting Name Selectable Options ParkView Backup Camera Delay — If Equipped NOTE: The “ParkView Backup Camera Delay” setting determines whether or not the screen will display the rear view image with dynamic grid lines for up to ten seconds after the vehicle is shifted out of REVERSE.
Page 481 MULTIMEDIA Setting Name Selectable Options Forward Collision Warning Only Warning & Braking Warning — If Equipped NOTE: Changing the FCW status to “Off” prevents the system from warning you of a possible collision with the vehicle in front of you. The FCW system state is kept in memory from one ignition cycle to the next.
Page 482 480 MULTIMEDIA Setting Name Selectable Options ParkSense — If Equipped Sound Only Sound and Display NOTE: The “ParkSense” system setting will scan for objects behind the vehicle when the transmission gear selector is in REVERSE and the vehicle speed is less than 7 mph (11 km/h), when enabled. It will provide an alert (audible and/or visual) to indicate the proximity to other objects.
Page 483 MULTIMEDIA Setting Name Selectable Options Blind Spot Alert — Lights Lights and Chime If Equipped NOTE: When the “Blind Spot Alert” feature is selected, the Blind Spot Alert system is activated and will show a visual alert in the outside mirrors, or it will show a visual alert in the outside mirrors as well as play an audible alert when the turn signal is on.
Page 484 482 MULTIMEDIA Mirrors & Wipers After pressing the “Mirror and Wipers” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Rain Sensing Auto Wipers Tilt Side Mirrors in Reverse Auto Folding Side Mirrors Headlights with Wipers Lights After pressing the “Lights”...
Page 485 MULTIMEDIA Setting Name Selectable Options Headlights With Wipers — If Equipped Headlight Illumi- 0 sec 30 sec 60 sec 90 sec nated On Approach NOTE: When the “Headlight Illumination On Approach” feature is selected, it allows the adjustment of the amount of time the headlights remain on after the doors are unlocked with the key fob.
Page 486 484 MULTIMEDIA Doors & Locks After pressing the “Doors & Locks” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Auto Door Locks NOTE: When the “Auto Door Locks” feature is selected, all doors will lock automatically when the vehicle reaches a speed of 12 mph (20 km/h).
Page 487 MULTIMEDIA Setting Name Selectable Options When All Doors is selected for 1st Press Of Key Fob Unlocks, all doors will unlock on the first press of the key fob unlock button. If the vehicle is programmed 1st Press Of Key Fob Unlocks “All Doors,” all doors will unlock no matter which Passive Entry equipped door handle is grasped.
Page 488 486 MULTIMEDIA Auto-On Comfort — If Equipped After pressing the “Auto-On Comfort” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Auto-On Driver Heated/ Remote Start All Starts Vented & Steering Wheel With Vehicle Start — If Equipped NOTE: When this feature is selected the driver’s heated seat and heated steering wheel will automatically turn ON when...
Page 489 MULTIMEDIA Engine Off Options After pressing the “Engine Off Options” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Engine Off 0 sec 45 sec 5 min 10 min Power Delay — If Equipped NOTE: When the “Engine Off Power Delay”...
Page 490 488 MULTIMEDIA Audio After pressing the “Audio” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Balance/Fade Speaker Icon NOTE: When in this display you may adjust the “Balance/Fade” of the audio by pressing and dragging the “Speaker Icon” toward any location in the box.
Page 491 MULTIMEDIA Phone Settings After pressing the “Phone Settings” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Do Not Disturb List of Settings NOTE: Press “Do Not Disturb” to access the available settings. The following settings are: Auto Reply (both, text, call), Auto Reply Message (custom, default) and Custom Auto Reply Message (create message).
Page 492 490 MULTIMEDIA SiriusXM Setup — If Equipped After pressing the “SiriusXM Setup” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Tune Start NOTE: The “Tune Start” feature begins playing the current song from the beginning when you tune to a music channel using one of the twelve presets, so you can enjoy the complete song.
Page 493 MULTIMEDIA Setting Name Selectable Options 2. Write down the Sirius ID numbers for your receiver. To reactivate your service, either call the number listed on the screen or visit the provider online. SiriusXM Travel Link is a separate subscription. Accessibility — If Equipped After pressing the “Accessibility”...
Page 494 492 MULTIMEDIA Restore Settings After pressing the “Restore Settings” button on the touch- screen, the following settings will be available: Setting Name Selectable Options Restore Settings Cancel NOTE: When the “Restore Settings” feature is selected it will reset all settings to their default settings. Clear Personal Data After pressing the “Clear Personal Data”...
Page 495: Srt Performance Pages - If Equipped
MULTIMEDIA System Information After pressing the “System Information” button on the touchscreen, the following settings will be available: Setting Name Selectable Options Software License System Software Information Screen NOTE: When the “System Information” feature is selected, a “System Software Information” screen will appear, displaying the system software version.
Page 496: Home
494 MULTIMEDIA The Performance Pages include the following: The following describes each feature and its operation: • Home Home • Timers • Gauges • G-Force • Engine • Dyno Performance Pages — Home...
Page 497 MULTIMEDIA • Gauge: Engine Torque When Home is selected, a series of widgets (gauges) can be customized by the user. Follow these steps to change a • Gauge: Engine Power widget: • Gauge: G-Force • Gauge: Steering Angle 1. Pressing any of the gauges allows you to switch the display.
Page 498: Timers
496 MULTIMEDIA Timers When the Timers Page is selected, you will be able to select from following “Tickets”: • Recent Pressing the “Recent” button displays a “real time” sum- mary of performance timers. • Last Pressing the “Last” button displays the last recorded run of performance timers.
Page 499 MULTIMEDIA The “Tickets” contain the timers listed below: • Reaction Time Measures the driver’s reaction time for launching the vehicle against a simulated drag strip timing light (behav- ior modeled after 500 Sportsman Tree) displayed in the instrument cluster display. NOTE: The Reaction Time, MPH, ⅛...
Page 500: Gauges
498 MULTIMEDIA • ⅛ Mile (200 meter) MPH Gauges Displays the vehicle speed at the time ⅛ mile was reached. • ¼ Mile (400 meter) ET Displays the time it takes for the vehicle to go ¼ mile (400 meters). •...
Page 501 MULTIMEDIA • Coolant Temperature If a gauge is selected, the Gauge Detail View page will appear on the screen. This page shows further information Shows the actual coolant temperature. on the selected gauge. • Battery Voltage Pressing the left or right arrows will cycle through the Shows the actual battery voltage.
Page 502: G-Force
500 MULTIMEDIA G-Force When G-Force is selected, the following features will be available: • Vehicle Speed: Measures the current speed of the vehicle in either mph or km/h, starting at zero with no maximum value. • Front G-Force: Measures the braking force. •...
Page 503: Engine
MULTIMEDIA • Steering Wheel Angle Engine Steering Wheel Angle utilizes the steering angle sensor to measure the degree of the steering wheel relative to zero. The zero degree measurement indicates a steering wheel straight ahead position. When the steering angle value is negative, a turn to the left is indicated, and when the steering angle value is positive, a turn to the right is indicated.
Page 504: Dynamometer (Dyno)
502 MULTIMEDIA • Instantaneous Torque Dynamometer (Dyno) Shows the instantaneous torque. • Oil Pressure (6.4L Only) Shows the actual engine oil pressure. • Gear Shows the current (or pending) operating gear of the vehicle. Dyno Page The system starts drawing graphs for Power and Torque. The graph fills to the right side of the page (based on History time selected).
Page 505: Srt Drive Modes
MULTIMEDIA The following options can be selected: SRT DRIVE MODES • Pressing the STOP button will freeze the graph. Selecting Play will clear the graph and restart the process over. • Press the “+” or “–” buttons to change the history of the graph.
Page 506: Track Mode
504 MULTIMEDIA The Drive Modes feature is controlled through the head Listed below are the available Drive Modes: unit and may be accessed by performing any of the Track Mode following: • Selecting “Drive Modes” from the “Apps” menu. • Selecting “Drive Modes” from within the Performance Pages menu.
Page 507: Sport Mode
MULTIMEDIA NOTE: Electronic Stability Control (ESC) Full-Off can be Sport Mode activated by pushing and holding the ESC Off button on the instrument panel switch bank for five seconds. Drive Modes (Sport) Selecting “Sport” within the head unit activates the con- figuration for typical enthusiast driving.
Page 508: Tow Mode
506 MULTIMEDIA Tow Mode All-Wheel Drive is set to “50/50” highlighted in blue. Steering is set to “Street” highlighted in yellow. Suspension is set to “Sport” highlighted in orange. Drive Modes (Tow) Selecting “Tow” within the head unit will activate the configuration for towing a trailer.
Page 509: Snow Mode
MULTIMEDIA Snow Mode The Transmission is set to “Snow” setting highlighted in blue. Stability Control is set to “Full” highlighted in blue. All-Wheel Drive is set to “50/50” highlighted in blue. Steering is set to “Street” highlighted in yellow. Suspension is set to “Street”...
Page 510: Auto Mode
508 MULTIMEDIA Auto Mode Steering and Suspension can be configured in either the “Street,” “Sport,” or “Track” and the Paddle Shifters may be enabled or disabled while in auto set-up mode. Drive Mode Auto (Default) Auto Mode (Default) Auto mode is enabled upon ignition on, or by selecting “Auto”...
Page 511: Custom Mode
MULTIMEDIA Custom Mode While in Custom Mode, the All-Wheel Drive, Stability Control, Transmission, Steering, Suspension, and Paddle Shifter settings are shown in their current configuration. While in the Custom Mode screen, press the “Custom Set-Up” button on the touchscreen to access the selectable options.
Page 512: Race Options
510 MULTIMEDIA RACE OPTIONS Launch Control WARNING! Launch Mode is intended for off-highway or off-road use only and should not be used on any public roadways. It is recommended that this feature be used in a controlled environment, and within the limits of the law.
Page 513 MULTIMEDIA Launch Mode can be turned on or off by either pushing the Launch Control button on the console, or by pressing the “Cancel Launch Mode” button on the touchscreen. NOTE: Launch RPM Set-Up cannot be accessed unless Launch Mode is deactivated. Activate Launch Control Launch Control can be accessed by pushing the Launch button on the console or pushing the SRT button on the...
Page 514: Shift Light
512 MULTIMEDIA To adjust the Launch RPM, drag the slider bar or press the arrows on the touchscreen to adjust the holding RPM. The launch RPM limit will display in the head units tachometer display. Shift Light Your vehicle is equipped with a shift light feature that illuminates the back lighting of the tachometer (in red) within the instrument cluster display.
Page 515: Valet Mode
MULTIMEDIA Factory Default” button on the touchscreen to change back To enter Valet Mode press the “Valet” button on the to factory settings, or press the “Shift Light Off” button on touchscreen and a popup screen will ask you if you would the touchscreen to turn the system off completely.
Page 516 514 MULTIMEDIA Valet Mode Deactivation Valet Mode Deactivation PIN To exit Valet Mode you must enter the same four digit PIN The Valet Mode Deactivation key pad will then prompt that was used to enter the mode. The unlock keypad can be you for your four digit PIN code, enter your PIN code and accessed by either pushing the SRT button, or pressing the press the “OK”...
Page 517: Eco Mode
MULTIMEDIA ECO MODE Increased engine exhaust noise and/or vibration may be noticed while ECO is active. This is normal and a result of the increased amount of operating conditions where the vehicle is allowed to operate in four cylinder shutoff mode. The Paddle Shifters will be disabled while in ECO mode.
Page 518: Steering Wheel Audio Controls - If Equipped
516 MULTIMEDIA STEERING WHEEL AUDIO CONTROLS — Pushing the center button will make the radio switch IF EQUIPPED between the various modes available (AM/FM/SXM/CD/ AUX/VES, etc.). The remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to The left-hand control is a rocker-type switch with a push- access the switches.
Page 519: Ipod/Usb/Mp3 Control - If Equipped
MULTIMEDIA If you push the switch up or down twice, it plays the second track; three times, it will play the third, etc. IPOD/USB/MP3 CONTROL — IF EQUIPPED This feature allows an iPod or external USB device to be plugged into the USB port, located in the lower section of the front integrated center stack, in front of the rotary transmission gear selector.
Page 520: Using This Feature
518 MULTIMEDIA Using This Feature Second Row USB Charging Port By using an iPod cable, or an external USB device to Second row USB connector ports can be used for charging connect to the USB port: purposes only. Use the connection cable to connect an iPod or external USB device to the vehicle’s USB charging ports •...
Page 521: Uconnect Rear Seat Entertainment (Rse) System - If Equipped
MULTIMEDIA Getting Started • Screen(s) located in the rear of front seats: Open the LCD screen cover by lifting up on cover. Second Row Center Console USB Port UCONNECT REAR SEAT ENTERTAINMENT (RSE) SYSTEM — IF EQUIPPED Your Rear Seat Entertainment System is designed to give RSE System Screen •...
Page 522 520 MULTIMEDIA • When the Video Screen(s) are open and a DVD/Blu-ray • With the Dual Video Screen System, Channel 1 (Rear 1) disc is inserted into the disc player, the screen(s) turn(s) on the remote control and headphones, refers to Screen on automatically, the headphone transmitters turn on 1 (driver’s side) and Channel 2 (Rear 2) on the Remote and playback begins.
Page 523: Dual Video Screen
MULTIMEDIA Blu-ray Disc Player Play A Blu-ray Disc The Blu-ray disc player is located in the center console. RSE System Headphone Channel Selectors • The system can be controlled either by the front seat occupants utilizing the touchscreen radio or by the rear seat occupants using the remote control.
Page 524 522 MULTIMEDIA 3. To watch a Blu-ray disc on Rear 2 for passenger side rear Using The Touchscreen Radio passengers, ensure the Remote Control and Headphone switch is on Rear 2. NOTE: • To view a Blu-ray disc on the radio, press the “Media” button on the touchscreen, and then press the “Disc”...
Page 525: Play Video Games
MULTIMEDIA 3. RSE Mute 8. RSE Mode Mute rear headphones for the current ignition cycle. Press- Select this button to change source for the active (high- ing mute again will unmute rear headphones. lighted) rear Screen/Channel on the rear media control screen.
Page 526: Play A Dvd/Blu-Ray Disc Using The Touchscreen Radio
524 MULTIMEDIA Audio/Video RCA/HDMI Jacks (AUX/HDMI Jacks) on 3. Left audio in (white). the side of each seat enable the monitor to display video 4. Video in (yellow). directly from a video camera, connect video games for display on the screen, or play music directly from an MP3 NOTE: Certain high-end video games consoles may exceed player.
Page 527 MULTIMEDIA ENTER/OK. Using The Touchscreen Radio Controls 1. Press the Media button on the Uconnect system touch- screen. 2. Press the Rear Media button to display the Rear Media Control screen. Select DISC Mode On The Rear Seat Entertainment Screen Rear Media Control Screen...
Page 528: Important Notes For Dual Video Screen System
526 MULTIMEDIA 3. Press the 1 or 2 buttons on the touchscreen, and the Important Notes For Dual Video Screen System select source button on the touchscreen. Press the DISC • The Rear Seat Entertainment System is able to transmit button on the touchscreen in the MEDIA column.
Page 529: Blu-Ray Disc Player Remote Control - If Equipped
MULTIMEDIA Blu-ray Disc Player Remote Control — If Equipped 3. SOURCE — Push to enter Source Selection screen. 4. Channel/Screen Selector Switch — Indicates which channel is being controlled by the remote control. When the selector switch is in the Rear 1 position, the remote controls the functionality of headphone Channel 1 (left screen).
Page 530: Headphones Operation
528 MULTIMEDIA — Push and hold to fast rewind through the current audio track or video chapter. — Mutes headphone audio. 15. BACK — Push to exit out of menus or return to source selection screen. — Push to navigate menus. 17.
Page 531: Replacing The Headphone Batteries
MULTIMEDIA NOTE: The rear video system must be turned on before 4. When the Mode Selection menu appears on screen, use sound can be heard from the headphones. To conserve the cursor buttons on the remote control to navigate to battery life, the headphones will automatically turn off the available modes and push the OK button to select approximately three minutes after the rear video system is...
Page 532: Unwired Stereo Headphone Lifetime Limited Warranty
530 MULTIMEDIA Unwired Stereo Headphone Lifetime Limited states and jurisdictions may not allow the exclusion or Warranty limitation of incidental or consequential damages, so the above limitation may not apply to you. This warranty gives Who Does This Warranty Cover? This warranty covers the you specific legal rights.
Page 533 MULTIMEDIA System Information video on the screen. The factory default settings are already set for optimum viewing, so there is no need to change Disc Menu these settings under normal circumstances. When listening to a CD Audio or CD Data disc, pushing To change the settings, push the remote control’s naviga- the remote control’s POP UP/MENU button displays a list tion buttons ( ,...
Page 534 532 MULTIMEDIA • When the screen is reopened, the video screen will DVD Region Codes automatically turn back on and show the appropriate The Blu-ray Disc player and many DVD discs are coded by display menu or media. geographic region. These region codes must match in order If the screen is closed and there is no audio heard, verify for the disc to play.
Page 535 MULTIMEDIA If you record a disc using a personal computer, there may The recommended method for labeling recordable discs be cases where the Blu-ray Disc player may not be able to (CD-R, CD-RW, and DVD-R) is with a permanent marker. play some or the entire disc, even if it is recorded in a Do not use adhesive labels as they may separate from the compatible format and is playable on other players.
Page 536 534 MULTIMEDIA • Other compression formats such as AAC, MP3 Pro, Ogg the disc is reached, the Blu-ray Disc player will return to Vorbis, and ATRAC3 will not play. The Blu-ray player the beginning of the disc and attempt to play the start of will automatically skip the file and begin playing the the first track.
Page 537: Radio Operation And Mobile Phones
MULTIMEDIA RADIO OPERATION AND MOBILE PHONES The radio manufacturer believes the internal wireless radio is safe for use by consumers. The level of energy emitted is Under certain conditions, the mobile phone being on in far less than the electromagnetic energy emitted by wire- your vehicle can cause erratic or noisy performance from less devices such as mobile phones.
Page 538: Voice Commands
536 MULTIMEDIA NOTE: VOICE COMMANDS • This equipment has been tested and found to comply Introducing Uconnect with the limits for a Class B digital device, pursuant to Start using Uconnect Voice Recognition with these helpful Part 15 of the FCC Rules. These limits are designed to quick tips.
Page 539: Get Started
MULTIMEDIA NOTE: If you see the NAV icon on the bottom bar, or in the 5. You can interrupt the help message or system prompts Apps menus, of your touchscreen, you have the Uconnect by pushing the VR or Phone button and saying a Voice 4C NAV system.
Page 540: Basic Voice Commands
538 MULTIMEDIA Basic Voice Commands The basic Voice Commands below can be given at any point while using your Uconnect system. Push the VR button . After the beep, say: • “Cancel” to stop a current voice session • “Help” to hear a list of suggested Voice Commands •...
Page 541: Media
MULTIMEDIA TIP: At any time, if you are not sure of what to say or want Media to learn a Voice Command, push the VR button and say Uconnect offers connections via USB, Bluetooth and auxil- “Help.” The system will provide you with a list of iary ports (If Equipped).
Page 542: Phone
540 MULTIMEDIA Push the Phone button . After the beep, say one of the following commands: • “ Call John Smith” • “ Dial 123-456-7890 and follow the system prompts” • “ Redial (call previous outgoing phone number)” • “ Call back (call previous incoming phone number)” TIP: When providing a Voice Command, push the Phone button and say “Call,”...
Page 543: Climate (4C/4C Nav)
MULTIMEDIA • “ Set passenger temperature to 70 degrees” TIP: Voice Command for Climate may only be used to adjust the interior temperature of your vehicle. Voice Command will not work to adjust the heated seats or steering wheel if equipped. Uconnect 4C/4C NAV Phone Climate (4C/4C NAV) Too hot? Too cold? Adjust vehicle temperatures hands-free...
Page 544: Navigation (4C Nav)
542 MULTIMEDIA Navigation (4C NAV) The Uconnect navigation feature helps you save time and become more productive when you do not know exactly how to get to where you want to go. (Navigation is optional on the Uconnect 4C system.) 1.
Page 545: Register (4C Nav)
MULTIMEDIA NOTE: Your vehicle may be transmitting data as autho- Vehicle Health Reports** rized by the subscriber. Vehicle Health Alert** An included trial and/or subscription is required to take Performance Pages Plus** advantage of the SiriusXM Guardian services in the next **If vehicle is equipped.
Page 546: Mobile App (4C Nav)
544 MULTIMEDIA • Press the Location button on the navigation bar at the Mobile App (4C NAV) bottom of the app to bring up a map to locate your You’re only a few steps away from using remote com- vehicle or send a location to your vehicle’s navigation mands and playing your favorite music in your car.
Page 547: Android Auto - If Equipped
MULTIMEDIA Connect your Android 5.0 (Lollipop), or higher, to one of the media USB ports, using the factory-provided USB cable, and press the new Android Auto icon that replaces your “Phone” icon on the main menu bar to begin Android Auto.
Page 548: Apple Carplay - If Equipped
546 MULTIMEDIA Apple CarPlay — If Equipped Apple CarPlay allows you to use your voice to interact with Siri through your vehicle’s voice recognition system, and use your smartphone’s data plan to project your iPhone and a number of its apps onto your Uconnect touchscreen.
Page 549: General Information
MULTIMEDIA General Information The following regulatory statement applies to all Radio Frequency (RF) devices equipped in this vehicle: This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1.
Page 550: Cd/Dvd Disc Maintenance
548 MULTIMEDIA Uconnect System Support: 6. Do not expose the disc to direct sunlight. • U.S. residents visit DriveUconnect.com or call: 1-877- 7. Do not store the disc where temperatures may become 855-8400(24 hours a day 7 days a week) too high.
Page 551 CUSTOMER ASSISTANCE CONTENTS ▫ Customer Assistance For The Hearing Or SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE ......550 Speech Impaired (TDD/TTY) .
Page 552: Suggestions For Obtaining Service For Your Vehicle
550 CUSTOMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR IF YOU NEED ASSISTANCE YOUR VEHICLE The manufacturer and its authorized dealer are vitally interested in your satisfaction. We want you to be happy Prepare For The Appointment with our products and services. If you are having warranty work done, be sure to have the right papers with you.
Page 553: Fca Us Llc Customer Center
CUSTOMER ASSISTANCE 551 Any communication to the manufacturer’s customer center In Mexico Contact should include the following information: Av. Prolongacion Paseo de la Reforma, 1240 • Owner’s name and address Sante Fe C.P. 05109 • Owner’s telephone number (home and office) Mexico, D.
Page 554: Customer Assistance For The Hearing Or Speech Impaired (Tdd/Tty)
552 CUSTOMER ASSISTANCE Customer Assistance For The Hearing Or Speech If you have any questions about the service contract, call Impaired (TDD/TTY) the manufacturer’s Service Contract National Customer Hotline at 1-800-521-9922 (Canadian residents, call (800) To assist customers who have hearing difficulties, the 465-2001 English / (800) 387-9983 French).
Page 555: Warranty Information
CUSTOMER ASSISTANCE 553 REPORTING SAFETY DEFECTS WARNING! In The 50 United States And Washington, D.C. Engine exhaust (internal combustion engines only), If you believe that your vehicle has a defect that could some of its constituents, and certain vehicle compo- cause a crash or cause injury or death, you should nents contain, or emit, chemicals known to the State of immediately inform the National Highway Traffic...
Page 556: In Canada
554 CUSTOMER ASSISTANCE In Canada Diagnostic Procedure Manuals If you believe that your vehicle has a safety defect, you Diagnostic Procedure Manuals are filled with diagrams, should contact the Customer Service Department imme- charts and detailed illustrations. These practical manuals diately.
Page 557 INDEX...
Page 558 556 INDEX About Your Brakes ......457 Air Conditioner Maintenance ....405 Adaptive Cruise Control (ACC) (Cruise Control) .
Page 559 INDEX 557 Automatic High Beams ..... . .73 Brake Control System, Electronic....173 Automatic Temperature Control (ATC) .
Page 560 558 INDEX Car Washes.......451 Manual ....... .84 Cellular Phone .
Page 561 INDEX 559 Defroster, Windshield......254 Electronic Speed Control (Cruise Control) ..284 Diagnostic System, Onboard .
Page 562 560 INDEX Overheating ......385 Fog Lights .......363 Starting .
Page 563: Introduction
INDEX 561 Gear Ranges ......271 Hood Release ......108 Glass Cleaning .
Page 564 562 INDEX Jack Operation ..... .371, 376, 425 Liftgate Window Wiper/Washer ....83 Jump Starting .
Page 565 INDEX 563 Rear Tail Lamps ......363 Maintenance Free Battery .....401 Seat Belt Reminder .
Page 566 564 INDEX Capacity .......463 ParkSense System, Rear ....307, 316 Change Interval .
Page 567 INDEX 565 Pretensioners Remote Keyless Entry Seat Belts ......209 Arm The Alarm ......31 Disarm The Alarm .
Page 568 566 INDEX Schedule, Maintenance..... . .395 Reminder ......156 Seat Belt Untwisting Procedure .
Page 569 INDEX 567 Automatic Transmission ....268, 270 Power ....... .282 Shoulder Belts .
Page 570 568 INDEX Compact Spare ......444 To Open Hood ......108 Flat Changing .
Page 571 INDEX 569 Shifting .......268 Warning, Roll Over ......5 Transmitter, Garage Door Opener (HomeLink) .
Page 572 INSTALLATION OF RADIO TRANSMITTING The antenna cable should be as short as practical and EQUIPMENT routed away from the vehicle wiring when possible. Use Special design considerations are incorporated into this only fully shielded coaxial cable. vehicle’s electronic system to provide immunity to radio Carefully match the antenna and cable to the radio to frequency signals.

Dodge Durango SRT 2018 Owner's Manual

Introduction

Graphical

Getting to Know Your Vehicle

Getting to Know Your Instrument Panel

Safety

Starting and Operating

In Case of Emergency

Servicing and Maintenance

Quick Links

Chapters

Related Manuals for Dodge Durango SRT 2018

Summary of Contents for Dodge Durango SRT 2018