Related Manuals for Lepa AquaChanger 240
Summary of Contents for Lepa AquaChanger 240
- Page 1 AquaChanger 240...
-
Page 2: Specification
Specification Model LPWAC240-HF Material Copper Cold Plate Bearing Ceramic Bearing MTBF 50,000 hrs Motor Speed 2700rpm ±10% Pump Rated Voltage Rated Current 0.3A Dimension 274 x 120 x 27 mm Radiator Material Aluminum Material Rubber Tube Length 300 mm Weight (w/o fan) 730 g Intel ®... - Page 3 Part list Fan x 2 Back Plate x 1 Cooler x 1 Position Screw × 4 Square Washer x 1 Stand-off × 4 Case Screw × 8 Fan Screw × 8 Intel LGA2011 Screw × 4 Spring Screw × 4 Insulating Sheet ×...
- Page 4 Intel Installation AquaChanger 240...
- Page 5 Intel Installation Step 1 Attach the fan and the radiator to the case.
- Page 6 Step 2-1 LGA 775/1150/1151/1155/1156/1366 <If your CPU socket is Intel LGA 2011, please skip to step 3-2.> Install the screw into the corresponding LGA1366 position hole on the back plate for your LGA 115X CPU socket. LGA775 *Aligning...
- Page 7 Step 2-2 LGA775 For LGA 775, please attach and click the square washer to the center of the back plate.
- Page 8 Step 3-1 LGA 775/1150/1151/1155/1156/1366 Install the back plate on the back of motherboard; place the stand-off on the motherboard to fix the back plate.
- Page 9 Step 3-2 LGA 2011/2011-3 Please fasten the LGA 2011 screw directly to the motherboard until all four screws are secured. (Socket LGA 2011 does not required to use the back plate for installation)
- Page 10 Step 4 Install the Intel bracket to the pump.
- Page 11 Step 5 Apply the thermal grease on the CPU surface.
- Page 12 Step 6 Remove the protection film on the cold plate.
- Page 13 Step 7 Place the pump on the CPU and tighten the four spring screws.
- Page 14 Pump Pump Step 8 3 pin 4 pin Connect the pump power connector to 3-pin or 4-pin connector on the motherboard. Notice: If you recognize that your mainboard's CPU fan or PWM sockets do not provide enough voltage to power the pump, please use the included 4-pin Molex adaptor and connect the pump directly to your PSU.
- Page 15 Step 9 Connect the fan connector to the 4-pin connector on the motherboard.
- Page 16 AMD Installation AquaChanger 240...
- Page 17 AMD Installation Step 1 Attach the fan and the radiator to the case.
- Page 18 Step 2 Stick the insulating sheet on the corresponding position.
- Page 19 Step 3 Please remove the original heatsink mount holder before further installation.
- Page 20 Step 4 Please attach and click the square washer to the center of the back plate and install the screw into the corresponding position hole on the back plate for your CPU socket. *Aligning...
- Page 21 Step 5 Install the back plate on the back of motherboard; place the stand-off on the motherboard to fix the back plate.
- Page 22 Step 6 Install AMD bracket to the pump.
- Page 23 Step 7 Apply the thermal grease on the CPU surface.
- Page 24 Step 8 Remove the protection film on the cold plate.
- Page 25 Step 9 Place the pump on the CPU and tighten the four spring screws.
- Page 26 Pump Pump Step 10 3 pin 4 pin Connect the pump power connector to 3-pin or 4-pin connector on the motherboard. Notice: If you recognize that your mainboard's CPU fan or PWM sockets do not provide enough voltage to power the pump, please use the included 4-pin Molex adaptor and connect the pump directly to your PSU.
- Page 27 Step 11 Connect the fan connector to the 4-pin connector on the motherboard.