Kurth Electronic KE7200 Operating Manual
Hide thumbs
Also See for KE7200:
- Operating manual (20 pages) ,
- Operating manual (24 pages) ,
- Operating instructions manual (29 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Kurth Electronic KE7200
Summary of Contents for Kurth Electronic KE7200
- Page 1 Operating Manual Ethernet Performance Tester KE7200 LAN Cable Tester KE7100 Version 1 - Copyright 2011 KURTH ELECTRONIC GmbH All rights reserved, including translations. All reprints and electronic copies, including excerpts, require prior written approval of...
-
Page 2: Introduction
All of the brand names and trademarks cited herein are the property of their registered owners. Introduction The KE7200 / KE7100 you purchased is an easy-to-operate, intuitive LAN tester. Please read the entire instruction manual first to help you use the KE7200 / KE7100 effectively. - Page 3 Operating Manual KE7200 / KE7100 Ethernet comm port Test port Display SEL (enter) button (back) button Menu LEFT – RIGHT Menu controls UP – DOWN controls ON-OFF button KURTH ELECTRONIC FERNMELDETECHNIK www.kurthelectronic.de sales@kurthelectronic.de...
-
Page 4: Safety Instructions
KE7200 / KE7100 Safety Instructions The KE7200 / KE7100 may only be operated with the accessories originally provided. Using the device with accessories that are not original or for applications for which it was not intended can lead to incorrect test results and may damage the device. -
Page 5: Table Of Contents
Operating Manual KE7200 / KE7100 Table of contents Introduction ______________________________ 2 Safety Instructions _________________________ 4 Applications: ____________________________ 7 Using the KE7200 / KE7100 ________________10 Keypad __________________________________10 ESC ______________________________________ 10 ON/OFF ___________________________________ 10 Four arrow buttons __________________________ 10 SEL button _________________________________ 10 Test settings ______________________________10 Wiring (Main menu>Setup>Wiring) _____________ 10... - Page 6 Operating Manual KE7200 / KE7100 Testing with the KE7200 / KE7100 ____________ 13 Cable test (Main menu) ________________________13 Performing the test ___________________________14 Save the data ________________________________15 Cable/wire trace _____________________________15 PoE/PoE+ test per IEEE 802.3af/at ______________16 IP test______________________________________16 Transmit measurements _______________________17...
-
Page 7: Applications
Operating Manual KE7200 / KE7100 Applications: Testing and starting up 10/100/1000 Mbit LAN networks, Verifying new LAN installations Troubleshooting existing LAN installations Logging network tests Cable mapping Fault finding Testing PoE/PoE+ performance Measuring length, finding cables of all kinds, coaxial cables, etc. - Page 8 Operating Manual KE7200 / KE7100 KE7200 only: Test active 10/100/1000 Mbit network - Information about service type - Static IP or DHCP - Network scan - List all found subscribers - Display name, IP address, MAC address - Targeted ping of individual addresses...
- Page 9 Operating Manual KE7200 / KE7100 Power supply 4 x UM-3 / AA battery or 4 x rechargeable batteries of the same size Battery life with a good quality battery (such as a GP Super Alkaline or Varta Industrial) Measurement always with the illuminated display...
-
Page 10: Using The Ke7200 / Ke7100
Keypad When the KE7200 / KE7100 was developed, emphasis was placed on fast and easy operation. For this reason, the KE7200 / KE7100 has only seven buttons despite its many test options. Similar to a PC, the ESC button means “undo the last step.”... -
Page 11: Cable Type (Main Menu>Setup>Cable Type)
(meters) or ft (feet) Battery type The KE7200 / KE7100 can be operated with 4 AA batteries, or 4 AA rechargeable batteries. Since the voltage is lower with rechargeable batteries, the capacity display can be changed to reflect primary batteries and rechargeable batteries. -
Page 12: Auto Power Off
Operating Manual KE7200 / KE7100 Auto power off The time when the tester automatically turns off after the last button has been pressed. Set with the ▲ or ▼ button, select with SEL. Key beep On or off Sound On or off. This sound occurs when the cable test finishes. -
Page 13: Remote Id
MAC address - KE7200 only The KE7200 comes with a MAC address set. All of the testers have the same address when delivered. To work in networks with MAC address verification, the address can be set to any value in this menu IP address (Main menu>Setup>IP address) -
Page 14: Performing The Test
The unique remote ID numbers show up in the saved records, too. With the 0.5 m patch cable, connect the KE7200 / KE7100 (supplied) to the port to be tested in the patch panel or wall jack. On the Main menu select "Cable test," start the test by pressing the SEL button. -
Page 15: Save The Data
The KE7200 / KE7100 has two different ways of identifying a known jack on the patch panel, switch or hub. Insert the test cable of the KE7200 / KE7100 into the outlet box in the room and select Test Link/Blink in the Cable/wire trace menu. -
Page 16: Poe/Poe+ Test Per Ieee 802.3Af/At
IP test – KE7200 only In the IP test, the KE7200 can search the network for IP addresses and users. This can be done in DHCP mode or with a fixed IP. If the network is also monitoring MAC addresses, the MAC address of the KE7200 can be changed. -
Page 17: Transmit Measurements
Manager window. The KE7200 can now be disconnected from the network. If there are no saved measurements, this is reported. The data on the KE7200 can be deleted. If they should not be deleted, press ESC. KURTH ELECTRONIC FERNMELDETECHNIK www.kurthelectronic.de... -
Page 18: Changing The Battery
Operating Manual KE7200 / KE7100 Appendix A Changing the battery Changing batteries: First loosen the two bottom screws in the bottom bumper. Pull the bumper downward. The four AA batteries are in a holder. Remove the old batteries and replace them with new batteries. Note the polarity. Do not combine new and old batteries. - Page 19 Operating Manual KE7200 / KE7100 Sixteen common versions are predefined. The abbreviations UTP, STP, and CR are described on page 10 under Wiring. The list appears after the menu item "Wiring definition" is selected. The first item is "NO TEST". Do not change this one.
-
Page 20: Ke Manager
The KE Manager is only available in a Windows version. Operating systems: Windows 2000 – Windows 7, 8.1 and 10 Functions The KE Manager is a flexible tool for managing the KE7200 and downloading measurement data. It has the following functions: Configuring the Manager... -
Page 21: The Following Selection Options Are Offered
Load data (PC) Saved test sequences can be reloaded here. Save data Sequences loaded by the KE7200 are saved on the PC or on the network. Save displayed data After the data are selected, they are saved as a separate list. -
Page 22: Customer Address
Operating Manual KE7200 / KE7100 Customer address In the bottom section, you can enter the customer address, technician and any comments. The address entered in the first record is output as the first item in the log. You can then enter the technician, room name and comments separately for the individual records. -
Page 23: Overview Of Technical Data
Operating Manual KE7200 / KE7100 Overview of technical data KE7200 Ethernet Performance Tester / KE7100 LANcheck Copper wiring test: Test of the data line assignment with the pin and pair assignment. Sixteen predefined connection versions; easily create your own definitions as simple as single pair. - Page 24 Relative humidity: 90%, no condensation Basic model of KE7200 comes with: KE7200 network tester; 2 KE7010 remote units; 3 shielded CAT6 test cables, 0.5m long; 1 RJ45/RJ11 test cable, 4/5 pin, 2m long; 1 RJ45 test cable with two 4-mm banana plugs with alligator clips, 2m long; 1 RJ45/BNC adapter;...
Need help?
Do you have a question about the KE7200 and is the answer not in the manual?
Questions and answers