Download Print this page

sky viper E1700 Flying Manual

Stunt drone builder

Advertisement

Quick Links

E1700
STUNT DRONE BUILDER
POWERING UP AND PAIRING
Insert fully charged LiPo battery into
theunderside of the drone, then connect the
battery to back of the drone. (See next page.)
BASIC FLIGHT MANEUVERS
To make flying easier, place the drone on the ground in front of you
with the drone facing away from you (green blades forward). You
should be facing the same way the drone is facing.
L
Press LAUNCH to automatically launch a few feet off the ground.
Move LEFT (Throttle) thumb stick up or down to make drone
fly higher or lower and left or right to rotate.
Use RIGHT (Directional) thumb stick to fly forward,
backward, left or right.
Press LAND to automatically land.
Alternatively you can use the left thumb stick to land the drone. Hold the left
thumb stick all the way down for about 2.5 seconds after the drone has
safely reached the ground, and the motors will stop spinning.
AUTO AND MANUAL FLIGHT MODES
AUTO mode is best for new
pilots. Begin by pressing the
LAUNCH button for takeoff.
The drone will hold its altitude,
and gradually fly up or down
when you press up or down on
the left thumb stick.
MANUAL mode is better for
experienced pilots. When the left
thumb stick is pushed all the way
up the drone will spin its motors
as fast as it can while maintaining
stability, and when the left thumb
stick is pushed all the way down
the motors will stop spinning
completely.
01742
Place the drone on level surface for
calibration.
R
LAUNCH
LAND
L
R
LAUNCH
L
R
LAUNCH
LAND
L
R
LAUNCH
LAND
L
R
LAUNCH
LAND
Turn on controller. (Before initial use, install
new batteries into controller. See reverse.)
FLIGHT CONTROLS
Up
Rotate
Rotate
Right
Left
Down
Stunt Button
Power
Rotation Trim
Auto Mode
Indicator
Flight Mode
Manual Mode
Indicator
FLIGHT SENSITIVITY SWITCH
LOW
MED
HIGH
1 2 3
1 2 3
It is best to start with LOW sensitivity
until you master flying.
• Reset controller to
factory settings:
Hold F Trim, B Trim,
and Power for
3 seconds.
R
ONE TOUCH STUNTS
L AUNCH
NOTE:
L AND
Once a stunt has been initiated, DO NOT adjust Throttle or press any other controls until the stunt has been completed.
BARREL ROLL LEFT OR RIGHT
While flying forward (or reverse), tap the STUNT button.
FLIP IN 4 DIRECTIONS
1 Bring the drone to a mid-air hover without flying in any
direction. Remove finger from the RIGHT thumb stick.
2 While hovering, tap and hold the STUNT button.
3 Then quickly tap the RIGHT thumb stick in the direction
you want the drone to flip.
CAUTION!
The drone should be flying at least 6 feet in the air with a minimum clearance of 6 feet in all directions before
attempting stunt functions.
REPLACING DAMAGED BLADES
Use the included
screwdriver to unscrew
the propeller, then pull up
on propeller to detach.
Match A propellers to A
legs and B propellers to B
legs. Replace screws and
tighten. See image to right.
FLYING GUIDE
Once lights turn solid, drone is ready to fly.
Fly Forward
Fly Left
Fly Backward
LAUNCH/LAND BUTTON
1 2 3
PRESS TO LAUNCH
PRESS TO LAND
If for any reason you need to immediately stop
the drone, hold down the stunt button (for drones
that don't have a stunt button, use the video
button) and move both thumb sticks down and
away from the center of the controller.
A
B
Fly Right
Forward/
Backward Trim
Left/Right Trim
Front
B
A

Advertisement

loading

Summary of Contents for sky viper E1700

  • Page 1 FLYING GUIDE E1700 STUNT DRONE BUILDER POWERING UP AND PAIRING Once lights turn solid, drone is ready to fly. Insert fully charged LiPo battery into Place the drone on level surface for Turn on controller. (Before initial use, install theunderside of the drone, then connect the calibration.
  • Page 2 TRIM ADJUSTMENTS AND CHARGING E1700 STUNT DRONE BUILDER CONTROLLER MODE SKY VIPER FLIGHT SIMULATOR When the controller is OFF, press and hold Learn and practice maneuvers on your phone, then apply the flight mode button, LAUNCH/LAND your new skills in real life.
  • Page 3 4X Black Propellers 19. Antenna housing 10. Screws (A)(B)(C)(D)(E) 20. Sensitivity switch APP INSTRUCTIONS STEP ONE DOWNLOAD THE SKY VIPER BUILDER APP FOR FREE - Animated step-by-step instructions - Learn how drones work Insert the motor connectors into the flight controller board.
  • Page 4 ASSEMBLY E1700 STUNT DRONE BUILDER STEP FOUR STEP FIVE Slide  each of the motors into the motor casing until the gears mesh properly with Neatly tuck the motor wires into the guides in the center of each arm of the drone.
  • Page 5: Controller Assembly

    CONTROLLER ASSEMBLY E1700 STUNT DRONE BUILDER STEP ONE STEP TWO Place the front housing of the controller face down on a table. Now start placing Press the left and right joysticks covers down onto the joysticks.  Press the the buttons into their relevant sockets ensuring each is seated around their sensitivity switch down on to the sensitivity slider.