Table of Contents
Advertisement
P
ICTURE
A
DJUSTMENTS
T
o adjust your TV picture
controls, select a channel
and follow these steps.
F
M
M
ODE
F
M
M
ODE
T
his feature enables you to
receive FM radio stations.
FM Mode
• If you turn off the TV in FM mode, the TV will be in TV
mode when you turn on the TV again.
• You may get better FM reception by repositioning the TV.
• The TV's FM radio has a built-in antenna with a band
range of 88.0 ~ 108.0MHz.
• The radio frequency will not appear on the TV screen if
the volume is muted.
G
LOSSARY
Coaxial Cable - A single cable with a metal connector that screws (or pushes) direct-
ly onto a 75Ω jack (ANT(enna) In jack) on the Television or VCR.
Display - Allows the user to quickly confirm what channel number is being viewed
currently.
Jack Panel - The area on the back of the TV.
Menu - An on-screen listing of features that are available for adjustments.
On-screen Displays (OSD) - The wording or messages that help you set up features
(color adjustment, channel setup, etc.).
F
EATURES
Press the MENU
button, then press the
CH(annel)
/
buttons to
select a control.
SETUP
B
EXIT
B
BRIGHTNESS
24
COLOR
31
PICTURE
31
Press the FM button on
the remote control to
select the FM mode. The
current radio frequency
appears on the TV screen.
The radio frequency indicator
will move or shift while on the
TV screen during normal FM
mode operation.
FM 88.0MHz
(C
'
)
ONT
D
Press the VOL(ume)
B/{ buttons to adjust the
selected picture control.
POWER
TV/AUX
SLEEP
CH.
VOL.
VOL.
CH.
STATUS/EXIT
1
2
3
4
5
6
7
8
9
FM
0
ALT. CH
Press the CH(annel)
/
buttons until your
desired radio frequency
appears.
To exit FM mode and
return to TV mode, press
the FM button.
Programming - Adding or deleting channels in the television's memory. The televi-
sion "remembers'' only the locally available or desired channel numbers and skips over
any unwanted channel numbers.
Remote Sensor - An area on the front of the TV through which remote control sig-
nals are received.
Twin Lead Wire - The two-strand 300Ω antenna wire used with many indoor and
outdoor antenna systems. In many cases, this type of antenna wire requires an addition-
al adaptor (or balun) in order to connect to the ANT(enna) In jack on the TV.
Volume Indicator - Appears on the TV screen when you adjust the volume.
- 7 -
Press the
STATUS/EXIT button.
BRIGHTNESS Press the VOL(ume) B/{ buttons
until the darkest parts of the picture are as bright as
you prefer.
COLOR Press the VOL(ume) B/{ buttons to add
or reduce color.
PICTURE Press the VOL(ume) B/{ buttons until
the lightest parts of the picture show good detail.
SHARPNESS Press the VOL(ume) B/{ buttons
to improve detail in the picture.
TINT Press the VOL(ume) B/{ buttons to obtain
natural skin tones.
POWER
TV/AUX
SLEEP
CH.
VOL.
VOL.
CH.
STATUS/EXIT
1
2
3
4
5
6
7
8
9
FM
0
ALT. CH
S
MART
H
ELP
If you receive a
weak radio signal, you
may switch between the
internal (INT) or exter-
nal (EXT) antennas by
following the steps
below.
1) Press the FM button
to exit the FM mode
and return to TV mode.
2) Press the MENU but-
ton.
3) Press the CH(annel)
/
buttons to select
SETUP. Then, press the
VOL(ume) B or { but-
ton to continue.
4) Press the CH(annel)
/
buttons to select
FM ANTENNA. Then,
press the VOL(ume) B
or { button to select
INT or EXT.
5) Press the
STATUS/EXIT button.
Advertisement
Table of Contents
