Zhejiang Dahua Security Technology IPC-HD1100C User Manual

Hd mini network

Advertisement

Quick Links

Dahua HD Mini Network Dome Camera User's Manual
Version 1.2.1
Zhejiang Dahua Technology CO., LTD.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the IPC-HD1100C and is the answer not in the manual?

Questions and answers

Summary of Contents for Zhejiang Dahua Security Technology IPC-HD1100C

  • Page 1 Dahua HD Mini Network Dome Camera User’s Manual Version 1.2.1 Zhejiang Dahua Technology CO., LTD.
  • Page 2 Welcome Thank you for purchasing our network camera! This user’s manual is designed to be a reference tool for your system. Please read the following safeguard and warnings carefully before you use this series product! Please keep this user’s manual well for future reference!
  • Page 3: Important Safeguards And Warnings

    Important Safeguards and Warnings 1.Electrical safety All installation and operation here should conform to your local electrical safety codes. The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited power source is rated 12V DC or 24V AC in the IEC60950-1. (Refer to general introduction) Please note: Do not connect these two power supplying sources to the device at the same time;...
  • Page 4 Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens surface. Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to dilute the mild detergent first and then use it to clean the device.
  • Page 5: Table Of Contents

    Table of Contents General Introduction ........................1 Overview ........................1 Features ......................... 1 Specifications ........................ 2 1.3.1 Performance ......................2 Framework ........................... 9 Structure ........................9 Dimensions ........................10 Installation..........................13 Device Installation ...................... 13 Quick Configuration Tool ......................15 Overview ........................
  • Page 6: General Introduction

    1 General Introduction 1.1 Overview This series network camera integrates the traditional camera and network video technology. It adopts audio and video data collection, transmission together. It can connect to the network directly without any auxiliary device. This series network camera uses standard H.264 video compression technology and MJPEG audio compression technology, which maximally guarantee the audio and video quality.
  • Page 7: Specifications

    Support electronic shutter and gain setup.  Support dual bit stream, support ACF. 1.3 Specifications 1.3.1 Performance Please refer to the following sheet for network camera performance specification. Model IPC-HD1100C IPC-HD1105C Parameter Main High performance DSP Processor Embedded LINUX System...
  • Page 8 Activation event: video storage, image snapshot, log, email function and Video Loss etc. Wire Network 1-channel wire Ethernet port, 10/100 Base-T Ethernet Standard HTTP, TCP/IP, IPv4/IPv6, ARP, IGMP, ICMP, RTSP, RTP, Network UDP, SMTP, FTP, DHCP, DNS, DDNS, PPPOE, UPNP, NTP, Bonjour, Protocol SNMP.
  • Page 9 PAL: Main stream (1920*1080@25fps) Extra stream (704*576@25fps) Video Frame Rate NTSC: Main stream (1920*1080@30fps) Extra stream (704*480@30fps) H.264H: 16Kbps-8192Kbps, adjustable Video Bit Rate MJPEG adjustable and bit rate is adjustable. Support customized setup. Support mirror function. Video Flip Support flip function. Snapshot Max 1f/s snapshot.
  • Page 10 Model IPC-HDB4100C-A IPC-HDB4200C-A IPC-HDB4300C-A Parameter Series Series Series Main High performance DSP Processor Embedded LINUX System Support real-time network, local record, and remote operation at the Resources same time. User Interface Remote operation interface such as WEB, DSS, PSS System Status SD card status, bit stream statistics, log, and software version.
  • Page 11 Support mirror function. Video Flip Support flip function. Snapshot Max 1f/s snapshot. File extension name is JPEG. Privacy Mask Supports max 4 privacy mask zones Support max 4 ROI. Video Setup Support parameter setup such as bright, contrast. Video Channel title, time title, motion detect, privacy mask, overlay. Information Lens 2.8mm/3.6mm/6mm/ fixed focus...
  • Page 12 Model DH-IPC-HD1100C-W DH-IPC-HD2200C-W Parameter Main High performance DSP Processor Embedded LINUX System Support real-time network, local record, and remote operation at the Resources same time. User Interface Remote operation interface such as WEB, DSS, PSS System Status Bit stream statistics, log, and software version.
  • Page 13 Wire Network 1-channel wire Ethernet port, 10/100 Base-T Ethernet Wireless IEEE802.11a/b/g/n,built-in antenna Network Standard HTTP, TCP/IP, IPv4/IPv6, ARP, IGMP, ICMP, RTSP, RTP, Network UDP, SMTP, FTP, DHCP, DNS, DDNS, PPPOE, UPNP, NTP, Bonjour, Protocol SNMP. Remote Monitor, system setup, log information, maintenance , upgrade and etc Operation Access Support international, ONVIF...
  • Page 14: Framework

    2 Framework 2.1 Structure Please refer to the following figure for detailed information. See Figure 2-1 and Figure 2-2. Note: Figures in this chapter are for reference only. Different product models may refer to different figures. Please use figure (a) or (b) according to the actual product. Figure 2-1 Structure (a)
  • Page 15: Dimensions

    Figure 2-2 Structure (b) Please refer to the following sheet for detailed structure information. Name X-Y-Z rotation module Device lens Dome camera enclosure Please refer to the following sheet for detailed port information. Name Function Connect to the DC 12+ power to Power input port input the power.
  • Page 16 Please refer to the following figure for the dimension information. The unit is mm. See Figure 2-3 through Figure 2-5. Figure 2-3 Dimension illustration 1 Figure 2-4 Dimension illustration 2...
  • Page 17 Figure 2-5 Dimension illustration 3...
  • Page 18: Installation

    3 Installation 3.1 Device Installation Important Please make sure the installation surface can min support the 3X weight of the camera and the bracket. Please refer to the steps listed below. Figure 3-1 Device installation illustration 1 Figure 3-2 Device installation illustration 2 Step1 Use the inner hexagonal wrench (provided) to loose the three inner hexagon screws in the dome cover and then open the cover.
  • Page 19 Step 3 Draw and then dig three plastic expansion bolts holes on ceiling or other installation surface and then insert three expansion bolts in the holes. Secure these three bolts firmly. Note: Please dig a “cable exit hole” in the surface according to the installation map if you want to draw ...
  • Page 20: Quick Configuration Tool

    4 Quick Configuration Tool 4.1 Overview Quick configuration tool can search current IP address, modify IP address. At the same time, you can use it to upgrade the device. Please note the tool only applies to the IP addresses in the same segment. 4.2 Operation Double click the “ConfigTools.exe”...
  • Page 21 In the configuration tool search interface (Figure 4-1), please select a device IP address and then double click it to open the login interface. Or you can select an IP address and then click the Login button to go to the login interface. See Figure 4-3. In Figure 4-3, you can view device IP address, user name, password and port.
  • Page 22: Web Operation

    5 Web Operation This series network camera products support the Web access and management via PC. Web includes several modules: Monitor channel preview, system configuration, alarm and etc. 5.1 Network Connection Please follow the steps listed below for network connection. ...
  • Page 23 Figure 5- 2 Web login After you successfully logged in, please install WEB plug-in unit. Please refer to the Web Operation Manual included in the resource CD for detailed operation instruction. See Figure 5- 3. Figure 5- 3 Web monitoring window...
  • Page 24: Faq

    6 FAQ I can not boot up Please click RESET button for at least five seconds to restore the device. factory default setup. I can not upgrade When network upgrade operation failed, you can use port 3800 to device continue upgrade. network.
  • Page 25: Appendix Toxic Or Hazardous Materials Or Elements

    Appendix Toxic or Hazardous Materials or Elements Toxic or Hazardous Materials or Elements Component Name Cr VI PBDE Circuit Board ○ ○ ○ ○ ○ ○ Component Device ○ ○ ○ ○ ○ ○ Construction Material ○ ○ ○ ○ ○...

Table of Contents