Related Manuals for Zhejiang Dahua Security Technology F Series
Summary of Contents for Zhejiang Dahua Security Technology F Series
- Page 1 Dahua HD (IR) Vandal Proof Network Dome Camera Quick Start Guide Version 1.3.1 Zhejiang Dahua Technology CO., LTD...
- Page 2 Welcome Thank you for purchasing our network camera! This quick start guide is designed to be a reference tool for your system. Please keep this start guide well for future reference. Please open the accessory bag to check the items one by one in accordance with the list below. Contact your local retailer ASAP if something is missing or damaged in the bag.
- Page 3 Thunder-proof device is recommended to be adopted to better prevent thunder. The grounding studs of the product are recommended to be grounded to further enhance the reliability of the camera. 6. Daily Maintenance Please shut down the device and then unplug the power cable before you begin daily maintenance work.
-
Page 4: Table Of Contents
Table of Contents Structure ............................1 Dimensions ........................1 Port Description ......................1 Bidirectional talk......................7 1.3.1 Device-end to PC-end ..................7 1.3.2 PC-end to the Device-end ..................7 Alarm Setup ........................8 Installation..........................10 Device Installation Introduction ................10 Device Installation Steps ................... -
Page 5: Structure
1 Structure 1.1 Dimensions You can refer to the following figures for dimension information. The Unit is mm. See Figure 1-1 and Figure 1-2. Figure 1-1 Dimension 1 Figure 1-2 Dimension 2 1.2 Port Description For the non-IR series product, the interface is shown as in Figure 1-3 and Figure 1-4. Note：... - Page 6 Figure 1-3 Camera internal without IR (1-a) Figure 1-4 Camera internal without IR (1-b) See Figure 1-5.
- Page 7 Figure 1-5 Camera internal without IR (2) See Figure 1-6, Figure 1-7 and Figure 1-8. Figure 1-6 Motorized focus camera internal with IR (1-a)
- Page 8 Figure 1-7 Motorized focus camera internal with IR (1-b) Figure 1-8 Motorized focus camera internal with IR (2) See Figure 1-9, Figure 1-10 and Figure 1-11.
- Page 9 Figure 1-9 Manual focus camera internal with IR (1-a) Figure 1-10 Manual focus camera internal with IR (1-b)
- Page 10 Figure 1-11 Manual focus camera internal with IR (2) Please refer to the following sheet for external connection port definition information. Port Port Name Connector Function Description AC 24V power POWER Connect to AC 24V power. port DC 12V power POWER Connect to DC 12V power.
-
Page 11: Bidirectional Talk
Default input is DC 12V. network port external connected cable. Network port Ethernet port Connect to standard Ethernet port. Support PoE. Please refer to the following sheet for I/O port cable function information. Note: actual product may vary. -
Page 12: Alarm Setup
Please note the on-site listening operation is null during the bidirectional talk process. Listening Operation At the PC-end, speak via the speaker or the pickup, and then you can get the audio from the earphone or sound box at the device-end. 1.4 Alarm Setup The alarm interface is shown as in Figure 1-12. - Page 13 Figure 1-13 Alarm input Please refer to the following figure for alarm output information. See Figure 1-14. Port ALARM_COM and Port ALARM_NO composes an on-off button to provide the alarm output. If the type is NO, this button is normal open. The button becomes on when there is an alarm output. If the type is NC, this button is normal off.
-
Page 14: Installation
2 Installation Important Before you complete the installation and setup, do not remove the electrostatic attraction film on the transparent enclosure. Otherwise it may result in injury. After remove electrostatic attraction film, don’t touch dome enclosure in case it may leave stain. - Page 15 IR Motorized Zoom Lens Series Non-IR Series IR Manual Zoom Series Figure 2-2 Step 1 Take the installation position map from the accessories bag and then paste it on the installation ceiling or the wall according to the monitor area. Please dig three bottom holes of the plastic expansion bolts according to the map.
- Page 16 Figure 2-3 Step 4 Adjust the chassis of the device to the proper position and pull the cable to the cable exit of the installation surface. Line up the holes of the chassis to the three expansion bolt holes you dug in Step 1.
- Page 17 a) For the IR series product, you can skip current step and go the step b) directly. For the non-IR series product, push the port slightly to remove the decoration enclosure from the black plastic enclosure. See Figure 2-5. Figure 2-5 b) Lens pan rotation angle setup.
-
Page 18: Manual Zoom Lens Focus Operation
Lock screw B/C Adjust lens tilt rotation angle. Lock screw D Adjust lens pan rotation angle. Figure 2-7 e) For the motorized zoom series product, please skip current step. Please refer to chapter 2.2.1 for the lens zoom and focus operation of the manual focus series product. f) For the IR series product, please skip current step and complete the angle setup directly. -
Page 19: Side Cable Exit
Step 3 When you are securing the adjusting screw F, you can see the video may become blur. Please push the adjusting screw E to adjust the video slightly. Please secure the adjust screw E if you get a clear video. - Page 20 The device has two waterproof airproof plugs (One default position is the cable exit of the chassis of the device and the other is in the accessories bag.). The waterproof airproof plug has two functions. One is to fill in the cable exit and pull through the cable. It supports the cable whose diameter ranges from 4.0~6.0.
-
Page 21: Micro Sd Card Installation
2.3 Micro SD Card Installation Warning! Please unplug the device power cable and then shut down the device before you install the Micro SD card. Step 1 Please refer to Step 2 in chapter 2.2 installation steps to open the device protection enclosure. Step 2 Please find the “Micro SD”... -
Page 22: Quick Configuration Tool
3 Quick Configuration Tool 3.1 Overview Quick configuration tool can search current IP address, modify IP address. At the same time, you can use it to upgrade the device. Please note the tool only applies to the IP addresses in the same segment. 3.2 Operation Double click the “ConfigTools.exe”... - Page 23 In the configuration tool search interface (Figure 3-1), please select a device IP address and then double click it to open the login interface. Or you can select an IP address and then click the Login button to go to the login interface. See Figure 3-3. In Figure 3-3, you can view device IP address, user name, password and port.
-
Page 24: Web Operation
4 Web Operation This series network camera products support the Web access and management via PC. Web includes several modules: Monitor channel preview, system configuration, alarm and etc. 4.1 Network Connection Please follow the steps listed below for network connection. ... - Page 25 Figure 4- 2 Web login After you successfully logged in, please install WEB plug-in unit. Please refer to the Web Operation Manual included in the resource CD for detailed operation instruction. See Figure 4- 3. Figure 4- 3 Web monitoring window...
-
Page 26: Appendix Toxic Or Hazardous Materials Or Elements
Appendix Toxic or Hazardous Materials or Elements Toxic or Hazardous Materials or Elements Component Name Cr VI PBDE Circuit Board ○ ○ ○ ○ ○ ○ Component ○ ○ ○ ○ ○ ○ Device Case ○ ○ ○ ○ ○ ○...
Need help?
Do you have a question about the F Series and is the answer not in the manual?
Questions and answers