Advertisement
Advertisement
Table of Contents
Related Manuals for UCONNECT INTERNATIONAL BT-232B
Summary of Contents for UCONNECT INTERNATIONAL BT-232B
- Page 1 Uconnect Bluetooth Adapter RS-232 BT-232B User Manual...
- Page 2 User Manual V1.2 Date: 2009.04.18 Bluetooth RS-232 adapter user manual 1. Packing contents 1.1 Contents: RS-232 adapter x 1 Battery power line and connector x 1 User manual x 1 USB Cable x 1 1.2 Pictures: White box dimension: 13 x 10 x 6 (cm) (Open the box) (USB Cable) (Battery cable &...
-
Page 3: Parity: None
User Manual V1.2 Date: 2009.04.18 Data bit: 8 Parity: none Stop bit: 1 Flow control: H/W or none If not, please modify the setting by using hyper terminal software and the setup command via COM port. The setup command shows on the section 11. 2.5 Two RS-232 adapter connections (Please refer to the section 3): One is master and the other is slave. - Page 4 User Manual V1.2 Date: 2009.04.18 3.5 Two RS-232 adapters for micro controller. Remote site: (Serial Port) 1. Controller 2. Sensor 3. POS 4. Receipt printer 5. RFID 6. Card reader Controller with serial port 7. LED Display 8. etc.. 3.6 Handheld terminal with SPP profile Remote site: (Serial Port) 1.
- Page 5 User Manual V1.2 Date: 2009.04.18 6.2 Restore the factory settings (after over three seconds' press). 7. Slide Switch The slide switch can swap TXD/RXD and CTS/RTS signals. By switching, you can set the adaptor either as a DTE (towards antenna connector) or a DCE (towards RS232 connector).
- Page 6 User Manual V1.2 Date: 2009.04.18 4800 4800 bps 9600 9600 bps (Default) 19200 19200 bps 38400 38400 bps 57600 57600 bps 115200 115200 bps Inquire the current baud rate. BIT= Setup the data bit of the COM port (Default) 8 data bit Inquire the current data bit.
- Page 7 User Manual V1.2 Date: 2009.04.18 (CTS/RTS) of the UART port. Note, the setting is not affected by DEFAULT. Disable flow control. (Default) Enable flow control. Inquire the current setting NAME= This command is used to specify a name for the adaptor. You can specify a friendly name using 0 to 9, A to Z, a to z, space and –, which are all valid characters.
-
Page 8: Appendix 1: Specifications
User Manual V1.2 Date: 2009.04.18 (Default) One stop bit. Two stop bits. Inquire the current setting. VERSION= This command is used to inquiry the firmware version. Inquire the version codes. Appendix 1: Specifications: Specification Description Baud Rate Supports 1.2/2.4/4.8/9.6/19.2/38.4/57.6/115.2 Kbps Coverage Up to 100 m Connection... -
Page 9: Appendix 3: Rs232 Interface
User Manual V1.2 Date: 2009.04.18 Voltage Ration: 100V AC/DC Contact Resistance: 20mΩ Max. Withstand Voltage: 500V AC/Minute Insulation Resistance: 100MΩ Min. Temperature Range: -25 To +85 ℃ ℃ Appendix 3: RS232 Interface 1. Pin-out: 2 Signals: DCE Direction Signal DTE Direction Description Output Input... - Page 10 FCC ID: FCC Compliance and Advisory Statement This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Need help?
Do you have a question about the BT-232B and is the answer not in the manual?
Questions and answers