Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Arconic Manuals
  4. Tools
  5. ERT7
  6. Instruction manual

Arconic ERT7 Instruction Manual

Ebbert rivet tools
Hide thumbs

Advertisement

Quick Links

Download this manual
Instruction Manual
ERT7 ERT8
Ebbert Rivet Tools
Disassembly Instructions
Makers of Huck
December 9, 2016
Brand Fasteners, Tools & Accessories
HK1061
Assembly Instructions
Assembly Drawing &
Parts List ERT7
Assembly Drawing &
Parts List ERT8
, Marson
, Recoil
®
®
3-4
5
5
6
7
7-8
9
10
10
10
11
12
®

Advertisement

loading
Need help?

Need help?

Do you have a question about the ERT7 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Arconic ERT7

Summary of Contents for Arconic ERT7

  • Page 1: Table Of Contents

    Specifications Ebbert Rivet Tools Preparation for Use Maintenance Disassembly Instructions Assembly Instructions Kits and Accessories Troubleshooting Assembly Drawing & Parts List ERT7 Assembly Drawing & Parts List ERT8 Makers of Huck , Marson , Recoil December 9, 2016 ® ®...
  • Page 2 ERT7 and ERT8 Ebbert Rivet Tools (HK1061)

  • Page 3: Safety Instructions

    ERT7 and ERT8 Ebbert Rivet Tools (HK1061) Safety Instructions 15. Check clearance between trigger and work piece to ensure GLOSSARY OF TERMS AND SYMBOLS: there is no pinch point when tool is activated. Remote - Product complies with requirements set forth by triggers are available for hydraulic tooling if pinch point is the relevant European directives.
  • Page 4 ERT7 and ERT8 Ebbert Rivet Tools (HK1061) Safety Instructions (continued) IV. REPETITIVE MOTION HAZARDS: VIII. VIBRATION HAZARDS: 1. When using assembly power tool, the operator can 1. Exposure to vibration can cause disabling damage to the experience discomfort in the hands, arms, shoulders, neck nerves and blood supply to the hands and arms.

  • Page 5: General Information

    This manual contains operating and service procedures Specific instructions for each tool are given under that for the Ebbert Rivet Tool models ERT7 and ERT8. Pay tool model number heading. While the tools appear close attention to the recommended service procedures similar, each tool contains parts not used on other in this manual.

  • Page 6: Specifications

    ERT7 and ERT8 Ebbert Rivet Tools (HK1061) Specifications 2.10 6.32 53.4 ERT7 160.6 2.10 53.4 nches 50.8 INCHES WEIGHT: 3.0 lbs. (1.36 kg) RIVET SIZES: 1/8”, 5mm, 6mm ERT8 INCHES nches 13.33 338.6 10.47 265.9 9.38 238.4 3.50 88.9 WEIGHT: 3.25 lbs.

  • Page 7: Preparation For Use

    ERT7 and ERT8 Ebbert Rivet Tools (HK1061) Preparation for Use Use Ebbert Power Unit Model EPS6V or EPS6VL, that has tool. Observe the action of the tool and check for air been prepared for operation per applicable instruction leaks. Turn OFF the unit.

  • Page 8: Maintenance

    ERT7 and ERT8 Ebbert Rivet Tools (HK1061) Maintenance (continued) PREVENTIVE MAINTENANCE (continued) Pulling Head Maintenance Power Unit Maintenance Clean the pulling head assembly often. Dip it in mineral spirits (Figure 1), or similar solvent, to clean jaws and Refer to the applicable Power Unit instruction manual.
  • Page 9 Disassembly This manual provides operating and service procedures Rivet Tool Disassembly (Figures 2 & 3) for the Rivet Tool models ERT7 and ERT8. Close 1. Remove the Pulling Head Assembly from the tool; attention must be directed to the recommended remove all nicks and burrs from front of Piston Rod service procedures contained in this manual.

  • Page 10: Kits And Accessories

    ERT7 and ERT8 Ebbert Rivet Tools (HK1061) Assembly This procedure is for the re-assembly of the ERT7 and ERT8 Install the Double Piston onto the rear of the Piston Rod tools. For component identification, see Figures 2 and 3 and Assembly and into the cylinder until it bottoms on the Parts List.
  • Page 11 ERT7 and ERT8 Ebbert Rivet Tools (HK1061) Components Drawing & Parts List ERT7 Igure...
  • Page 12 ERT7 and ERT8 Ebbert Rivet Tools (HK1061) Assembly Drawing & Parts List ERT8 Igure...
  • Page 13 ERT7 and ERT8 Ebbert Rivet Tools (HK1061) Limited Warranties Limited Lifetime Warranty on BobTail® Tools: Tooling, Part(s) and Other Items not manufactured by Huck: Huck International, Inc. warrants to the original purchaser that its BobTail® installation tools manufactured after 12/1/2016 HUCK makes no warranty with respect to the tooling, part(s), or other items manufactured by third parties.
  • Page 14 Arconic Fastening Systems and Rings world-wide locations: AMERICAS EUROPE FAR EAST Kingston Operations...

This manual is also suitable for:

Ert8