Advertisement
Available languages
Available languages
OBJ_BUCH-718-006.book Page 7 Wednesday, November 25, 2015 2:45 PM
Safety Warnings for Drills
Use auxiliary handle(s), if supplied with the tool. Loss
of control can cause personal injury.
Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Cutting ac-
cessory contacting a "live" wire may make exposed metal
parts of the power tool "live" and could give the operator an
electric shock.
Use appropriate detectors to determine if utility lines are
hidden in the work area or call the local utility company
for assistance. Contact with electric lines can lead to fire
and electric shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property damage.
Switch off the power tool immediately when the tool in-
sert jams. Be prepared for high reaction torque that
can cause kickback. The tool insert jams when:
— the power tool is subject to overload or
— it becomes wedged in the workpiece.
Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
Always wait until the machine has come to a complete
stop before placing it down. The tool insert can jam and
lead to loss of control over the power tool.
Never use the machine with a damaged cable. Do not
touch the damaged cable and pull the mains plug when
the cable is damaged while working. Damaged cables in-
crease the risk of an electric shock.
Products sold in GB only: Your product is fitted with a
BS 1363/A approved electric plug with internal fuse (ASTA ap-
proved to BS 1362).
If the plug is not suitable for your socket outlets, it should be cut
off and an appropriate plug fitted in its place by an authorised
customer service agent. The replacement plug should have the
same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains sock-
et elsewhere.
Technical Data
Rotary drill
Article number
Rated power input
Output power
No-load speed
Rated speed
Rated torque
Spindle collar dia.
Speed control
Right/left rotation
Key type drill chuck
Keyless drill chuck
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Bosch Power Tools
Products sold in AUS and NZ only: Use a residual current de-
vice (RCD) with a rated residual current of 30 mA or less.
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
Intended Use
The machine is intended for drilling in wood, metal, ceramic
and plastic. Machines with electronic control and right and
left rotation are also suitable for screwdriving and tapping.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Keyless chuck*
2 Front sleeve
3 Rear sleeve
4 Belt clip
5 Handle (insulated gripping surface)
6 Lock-on button for On/Off switch
7 On/Off switch
8 Rotational direction switch (GBM 10 RE)
9 Chuck key*
10 Key type drill chuck*
11 Screwdriver bit*
12 Universal bit holder*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
GBM 10
GBM 10 RE
Professional
Professional
3 601 D73 0..
3 601 D73 5..
W
450
W
236
-1
min
2600
-1
min
1760
Nm
14
mm
43
–
–
–
English | 7
GBM 10 RE
Professional
3 601 D73 6..
450
450
236
236
0 – 2600
0 – 2600
0 – 1760
0 – 1760
14
14
43
43
–
–
1 609 92A 1W4 | (25.11.15)
Advertisement
