Seiko 4R57A Technical Manual

Seiko 4R57A Technical Manual

Automatic

Advertisement

Parts List / TECHNICAL GUIDE
Item
・3 Hands (Hour, Minute, Second)
・Date calendar Hand
・Power reserve indicator
  Driving system
Additional function
Normal position
Crown
1st click
operation
2nd click
Vibration per hour
Daily Rate
Loss/Gain
Standard rate
for measurement
Regulation system
Lift angle of the escapement
  Continuous operating time
Jewels
Automatic Cal.4R57A
Cal. No.
Automatic winding with manual winding mechanism
・Date correction function
・Second hand stop function
Manual winding (Clockwise only)
Date setting (Counterclockwise only)
Time setting (Hour and minute)
21,600 vibrations
Between +45 ~ -35 seconds
(Between 5℃ and 35℃)
Testing positions
Measurement
(Daily rate in
  seconds:s/d)
ETACHRON system
53°
From fully wound to stoppage : approximately 41 hours
29 jewels
4R57A
Movement Size
・Outside diameter: Ф29.36mm
・Height:
Instantaneous rate at T0
(Fully would condition)
Dial upward
6 o'clock at
the top
+25 s/d
+35 s/d
-15 s/d
-25 s/d
1/14
6.63 mm
Isochronous fault
9 o'clock at
Dial upward
the top
+35 s/d
±30 s/d
 
-25 s/d

Advertisement

Table of Contents
loading

Summary of Contents for Seiko 4R57A

  • Page 1 PARTS LIST / TECHNICAL GUIDE Automatic Cal.4R57A Cal. No. 4R57A Item ・3 Hands (Hour, Minute, Second) Movement Size ・Outside diameter: Ф29.36mm ・Date calendar Hand ・Height: ・Power reserve indicator 6.63 mm   Driving system Automatic winding with manual winding mechanism Additional function ・Date correction function...
  • Page 2 PARTS LIST Cal.4R57A Type of oil Oil quantity mark Disassembling procedures Figs. → AO-3 (Moebius A) NORMAL QUANTITY Reassembling procedures Figs. → SUFFICIENT QUANTITY 0439 190 Dial spacer 4408 245 Dial holding spacer (Back side) 0012 310 Auxiliary train wheel...
  • Page 3 PARTS LIST Cal.4R57A Type of oil Oil quantity mark NORMAL QUANTITY AO-3 (Moebius A) SUFFICIENT QUANTITY 0970 102 Date star 1001 128 0802 036 Date corrector setting unit (Back side) Date driving wheel 0810 164 Date jumper 0737 021 Date corrector setting wheel...
  • Page 4 PARTS LIST Cal.4R57A Type of oil Oil quantity mark AO-3 (Moebius A) NORMAL QUANTITY SUFFICIENT QUANTITY Oscillating weight ・Refer to page 7 for each parts code ・Refer to the page11 for assembling position 0012 354 Automatic train bridge screw 0012 420...
  • Page 5 PARTS LIST Cal.4R57A Type of oil Oil quantity mark NORMAL QUANTITY AO-3 (Moebius A) SUFFICIENT QUANTITY 0012 420 Barrel and train wheel bridge screw 0511 010 37-1 Cap jeweled spring First reduction wheel 37-2 Cap jewel ・Refer to page 8 for the oiling position ・Refer to page 10 for...
  • Page 6 PARTS LIST Cal.4R57A Type of oil Oil quantity mark NORMAL QUANTITY AO-3 (Moebius A) SUFFICIENT QUANTITY 0224 438 Center wheel with cannon pinion 0381 004 Click 0201 287 Barrel complete 0251 300 Escape wheel and pinion 0012 168 Yoke spring screw...
  • Page 7 PARTS LIST Cal.4R57A Oscillating weight with ball bearing Parts code Marking 1509 193 Japan mark 1509 194 ● List of screws Parts No Name Parts No Name 0012 919 Center wheel bridge 0012 354 screw 29 Ratchet wheel screw Pallet bridge screw (×2)
  • Page 8 TECHNICAL GUIDE Cal.4R57A Type of oil Oil quantity mark NORMAL QUANTITY AO-3 (Moebius A) SUFFICIENT QUANTITY 1.Oiling spot Barrel and train wheel bridge [Top side] [Back side] Note: After oiling , set Lower plate for barrel and train wheel bridge & screw.
  • Page 9 TECHNICAL GUIDE Cal.4R57A Type of oil Oil quantity mark NORMAL QUANTITY AO-3 (Moebius A) SUFFICIENT QUANTITY Planet unit Second sun wheel Notes: Oil to between the Arbor pinion and the Gear. Sun and planet unit Sun wheel Stop lever Stop lever...
  • Page 10 TECHNICAL GUIDE Cal.4R57A 2. Disassembling / Reassembling of the First reduction wheel << Disassembling >> << Reassembling >> First reduction wheel Reduction wheel holder Barrel and train wheel bridge (back side) 3. Disassembling / Reassembling of the Cannon pinion << Disassembling >>...
  • Page 11 TECHNICAL GUIDE Cal.4R57A 4. Disassembling / assembling of the Ratchet sliding wheel spring. << Disassembling >> << Reassembling >> Ratchet sliding wheel spring Barrel and train wheel bridge PUSH Remove the hook of the Ratchet sliding wheel spring The hooks of the Ratchet sliding wheel spring are hung from the Barrel and train wheel bridge.
  • Page 12 TECHNICAL GUIDE Cal.4R57A 6. How to remove the Winding stem 1) Set the W inding stem to normal position. 2) Pull out the W inding stem, while pushing "A" Setting lever W inding stem 7. Accuracy adjustment Regulator Regulator pin...
  • Page 13 TECHNICAL GUIDE Cal.4R57A 8. How to wind up the Mainspring The Mainspring can be fully wound either by hand or with Screwdriver. ・Manual winding …Turn the crown clockwise at least 55 times (equal to 8 turns of the Ratchet wheel screw) ・Screwdriver winding …...
  • Page 14 Operation Manual Cal.4R57A 【4R57A operation manual】 1. How to set the time 1) Pull out the crown to the second click position. 2) Turn the crown to set Hour and Minute hands. (Check if AM/PM is set correctly.) 3) Push the crown back into the normal position.

Table of Contents