Advertisement
Quick Links
ASSEMBLY INSTRUCTIONS
PLATFORM BED BY NERI&HU
PARTS
1x Central beam
13x Timber slats
(14 for Cal King)
1x Footboard
HARDWARE
(8x) Universal connector
(13x) M8x45 bolts
(26x) M5x45 bolts
YOU WILL NEED
-8mm socket/ratchet set OR cordless drill with the appropriate
attachment
-Phillips head screwdriver
-6mm and 5mm Allen Key
-The help of a friend
NOTES
NOTE 1: Be certain that all assembly is carried out on a flat
and stable surface. This will ensure a good final result.
Reverse the steps to disassemble the piece.
NOTE 2: Your furniture arrives packed in numerous layers that
protect it during transport. It is important that you remove
the packaging carefully to avoid damaging your furniture. Refer
to our information sheet "Unpacking Your Furniture" for further
details.
NOTE 3: Great care is required when assembling our products .
Use blankets to soften the assembly surface - hard surfaces
such as wood or stone flooring may damage the furniture if in
direct contact.
NOTE 4: We advise that assembly and disassembly of De La Espada
furniture is undertaken by a minimum of 2 people.
1x Headboard
with arms
2x Side beams
(8x) M8x40 Metal dowel
(2x) M8x60 bolts
(26x) M5x45 washers
1x Headboard
beam
SALES@DELAESPADA.COM
DELAESPADA.COM
0
1
N
E
R
I
&
H
U
Advertisement
Summary of Contents for NERI & HU 758
- Page 1 ASSEMBLY INSTRUCTIONS PLATFORM BED BY NERI&HU PARTS 1x Headboard with arms 1x Central beam 1x Headboard beam 13x Timber slats (14 for Cal King) 2x Side beams 1x Footboard & HARDWARE (8x) Universal connector (8x) M8x40 Metal dowel (13x) M8x45 bolts (2x) M8x60 bolts (26x) M5x45 bolts (26x) M5x45 washers...
- Page 2 ASSEMBLY INSTRUCTIONS CONTINUED PLATFORM BED NOTE 5: When screwing in bolts, tighten well, but be sure NOT TO OVERTIGHTEN. This can cause the thread to strip thus resulting in a poor connection. NOTE 6: All mating parts are numbered so they correspond to the appropriate part around the frame of the bed.
- Page 3 ASSEMBLY INSTRUCTIONS CONTINUED PLATFORM BED 2. TURN THE FRAME INTO ITS NATURAL UPRIGHT POSITION a) Turn the frame over into its natural position with the help of a friend. Be certain not to rest the frame on any individual leg whilst turning. &...
- Page 4 ASSEMBLY INSTRUCTIONS CONTINUED PLATFORM BED b)Insert the headboard with arms into the frame. & c) Insert M8x45 bolts into the 12 relevant pre-drilled holes in the headboard with arms. Tighten with an Allen Key.
- Page 5 ASSEMBLY INSTRUCTIONS CONTINUED PLATFORM BED 4. ATTACH CENTRAL BEAM a) Place the central beam on the underside of the frame, fitting it into the cutout in the base of the headboard with arms. In- sert a M8x45 bolt into the base of the headboard with arms and into the central beam as below.
- Page 6 ASSEMBLY INSTRUCTIONS CONTINUED PLATFORM BED b) Make sure the central beam is aligned with the holes in the footboard and headboard beam. Insert an M8x60 bolt into the end of each, and tighten with an Allen Key. & c) The frame should now look like this.
- Page 7 ASSEMBLY INSTRUCTIONS CONTINUED PLATFORM BED 6. ATTACH THE TIMBER SLATS TO THE PLATFORM BASE a) Space out the bed slats so they are aligned with the corresponding holes on the timber lip on the inner face of the side beams. The underside of the each slat has a threaded sleeve fixed inside.