Casio QW-2511 Service Manual & Parts List page 8

Alarms
The Alarm Mode gives you a choice of four one-time
Alarm on indicator
alarms and one snooze alarm. You can select either
Alarm screen
an audible beeper or flashing silent alert to let you
name
know when any of the alarm times is reached.
You can also input reminder text that appears when
the alarm time is reached.
Also use the Alarm Mode to turn the Hourly Time
Signal on and off.
• All of the operations in this section are performed
in the Alarm Mode, which you enter by pressing
C.
Alarm time
Alarm name indicator
To display Alarm Mode screen
In the Alarm Mode, use D to cycle through the alarm screens as shown
below.
ALARM1 ALARM2 ALARM3 ALARM4
• The following alarm screen names appear in the
Alarm1
center of the display to indicate the alarm whose
Alarm2
screen is currently displayed.
Alarm3
ALARM1 through ALARM4: One-time alarm
screen
Alarm4
SNOOZE: Snooze alarm screen
SIGNAL: Hourly Time Signal screen
• The currently displayed alarm screen is also
indicated by the alarm name indicators along the
Snooze
bottom left of the watch's display.
To set an alarm
1. In the Alarm Mode, use D to select the alarm
whose time you want to set.
2. Press B and the hour setting of the alarm time
starts to flash, which indicates the setting screen.
• Pressing A and D at the same time resets the
alarm time to 12:00 AM, and clears the reminder
text in the upper part of the display (if there is
any).
3. Press C to move the flashing in the sequence
shown below to select other settings.
Hour Minutes
• Selecting the text causes the text input cursor to appear. You can input up
to eight characters of reminder text for each alarm.
• There are eight spaces in the text, so you have to press C eight times to
move to the Hour setting.
4. When the setting you want to change is selected, use A and D to change
it.
• While the hour or minute setting is flashing, use D (+) and A (–) to
change it.
• When setting the alarm time using the 12-hour format, take care to set the
time correctly as a.m. (no indicator) or p.m. (P indicator).
• When inputting text, use A and D to cycle through characters at the
current cursor location, and C to move the cursor to the right. See
" Inputting Text " for more information.
5. Press B to exit the setting screen.
• If you input reminder text, the text appears in place of the alarm screen name
when you exit the setting screen.
• If the reminder text has more than six characters, it will scroll from right to left
whenever it is displayed.
Alarm Operation
The following table describes the different types of alarm operations that this
watch can perform.
Alarm on indicator
Alarm Operation
Type
Alarm off
Alarm on
Alert on
Snooze
indicator Alert on
indicator
• Press any button to stop the alarm after it starts to sound.
• If any alarm operation (one-time alarm, silent alert, snooze) occurs while a
signal receive operation is in progress, the receive operation is canceled.
• In the case of the snooze alarm, the alarm operation repeats up to seven
times every five minutes until the alarm is turned off.
• If you input reminder text for an alarm, the text appears for one minute in
place of the date on the Timekeeping Mode screen. The text is cleared from
the Timekeeping Mode screen if you change to another mode while it is
displayed.
• Alarm operations and the Hourly Time Signal operation are performed in all
modes.
• See information about selecting the alarm operation type.
SNOOZE SIGNAL
Text
Description
• Nothing happens when the alarm
time is reached.
• The alarm on indicator and alarm
name indicator flash on the
display for 10 seconds.
• The watch beeps for 10 seconds.
• The alert on indicator and alarm
name indicator flash on the
display for 10 seconds.
• The watch does not beep.
— 6 —
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
To select the alarm operation type
1. In the Alarm Mode, use D to select the screen for the alarm (ALARM1 to
ALARM4, or SNOOZE) whose alarm type you want to select.
2. Press A to cycle through the available settings in the sequence shown
below.
Alarm off Alarm on
• The alarm on indicator (
) and alarm name indicator are displayed for
each alarm (1 through 4, snooze) for which alarm on is set. The alert on
indicator
( ) and alarm name indicator are displayed for each alarm (1 through 4,
snooze) for which alert on is set.
• In other modes besides the Alarm Mode, the alarm name indicator is
displayed for each alarm for which alarm on is selected.
• In all modes, the alarm on indicator or alert on indicator is shown for any
alarm (ALARM1 through ALARM4, or SNOOZE) that is currently turned
on.
To turn the Hourly Time Signal on and off
1. In the Alarm Mode, use D to select the Hourly
Time Signal (SIGNAL).
2. Press A to toggle it on (SIG displayed) and off
(SIG not displayed).
• The Hourly Time Signal on indicator (SIG) is
shown on the display in all modes while this
function is turned on.
Data Memory
Remaining memory You can use the watch's data memory to store e-mail
addresses, Web page URLs, and other text data.
• All of the operations in this section are performed
in the Data Memory Mode, which you enter by
pressing C.
Data Memory Records
Each data memory record can contain up to 63
characters. Records are stored in memory in the
sequence they are created.
• The number of records you can store in data
memory depends on the number of characters that
make up each record. See " Data Memory
Management " for more information.
To create a new data memory record
1. In the Data Memory Mode, press A and D at the
same time to display the remaining memory
screen.
• You do not have to perform the above step if the
remaining memory screen is already on the
display.
• If REST 0% is shown for remaining memory, it
means that memory is full. To store another
record, you will first have to delete some of the
Cursor
records stored in memory.
2. Press B and the flashing cursor appears on the
display, which indicates the setting screen.
3. Use A and D to cycle through characters at the
current cursor location, and C to move the cursor
to the right. See " Inputting Text " for more
information.
• If memory becomes full while you are inputting
text, the cursor will jump to the first (leftmost)
character of the text when you press C, instead
of advancing to the right.
4. Press B to store your data and return to the data
Text
memory record screen (without the cursor).
• The message SAVE! appears for about two
seconds, followed by a data memory record screen,
which shows the text you just input in the upper
part of the display, and a record number
automatically assigned by the watch in the lower
part of the display.
• While the record number is in the lower part of the
Record number
display, you can see only six characters of the text
in the record. You can scroll through the text on the
screen by pressing D. See " To recall data memory
records " on the next page for more information.
To recall data memory records
1. In the Data Memory Mode, press A to scroll forward through data memory
records.
• Each press of A advances to the next record and shows its record
number and first six characters of its text.
• Pressing A while the last record in memory is on the display changes to
the remaining memory screen. Pressing A again displays the first record.
2. Press D to scroll through the text on the screen.
First six characters
Pressing D scrolls through the text.
• An end mark indicates the end of the text.
Alert on
End mark