Subscribe to Our Youtube Channel
Related Manuals for Maximum 058-9345-0
Summary of Contents for Maximum 058-9345-0
- Page 1 Air-powered Clipped-head Framing Nailer Model No. 058-9345-0 IMPORTANT: INSTRUCTION Please read this manual carefully before MANUAL using this product, and save it for reference.
-
Page 2: Table Of Contents
TABLE OF CONTENTS TECHNICAL SPECIFICATIONS SAFETY GUIDELINES KEY PARTS DIAGRAM TECHNICAL INFORMATION TYPES OF NAILS OPERATING INSTRUCTIONS MAINTENANCE TROUBLESHOOTING EXPLODED VIEW PARTS LIST WARRANTY NOTE: If any parts are missing or damaged, or if you have any questions, please call our toll-free helpline at 1-888-670-6682. -
Page 3: Technical Specifications
058-9345-0 | contact us 1-888-670-6682 SAFETY GUIDELINES TECHNICAL SPECIFICATIONS This manual contains information that relates to PROTECTING MAGAZINE CAPACITY 2 strips (up to 80 nails) PERSONAL SAFETY and PREVENTING EQUIPMENT PROBLEMS. It is very important to read this manual carefully and understand it NAILS 34°... -
Page 4: Safety Guidelines
Risk of bursting. Make sure the regulator is adjusted so that the loss of life. compressor outlet pressure is set lower than the maximum • Risk of electric shock. Do not expose a compressor to rain. operating pressure of the tool. Before starting the compressor, Store it indoors. - Page 5 058-9345-0 | contact us 1-888-670-6682 Potential hazard that may result in moderate injury or damage to equipment. Disconnect the tool from the air supply and turn off the compressor before performing any maintenance, Always ensure that the tool has stopped before connecting or changing accessories, when the tool is not in use, it to the air supply.
- Page 6 058-9345-0 | contact us 1-888-670-6682 Compatible compressors Description Description GUIDELINES FOR PROPER USE AND OPERATION Be sure to use a proper air compressor with MAXIMUM ® Air-powered Trigger Magazine pusher latch tools. The compressor should be able to supply a minimal air delivery of 6.63 CFM @ 90 PSI to ensure the compressor can run continuously with...
- Page 7 Always use clean, dry, regulated compressed air at 60 to 100 PSI (4 to 7 bar). Do not exceed the maximum and minimum pressures. Operating the tool at the wrong pressure will cause excessive noise, fast wear or misfiring.
-
Page 8: Types Of Nails
058-9345-0 | contact us 1-888-670-6682 This lightweight MAXIMUM ® Air-powered Clipped-head Framing Nailer Loading Nails Fig. C drives 2 to 3 1/4" (50 to 83 mm) long clipped-head framing nails. Operation Acceptable Nails 1. Disconnect the tool (1) from the air Length: 2 to 3 1/4"... - Page 9 058-9345-0 | contact us 1-888-670-6682 Operational Mode Insert a strip of nails into the magazine. Fig. E Ensure the points of the nails are facing The MAXIMUM Air-powered Clipped-head Framing Nailer can be down. Be sure to insert the heads of the operated either in manual or automatic firing mode.
- Page 10 058-9345-0 | contact us 1-888-670-6682 Mode Conversion Installing the New Trigger Fig. G Fig. I To convert the nailer from one Place the new trigger (1) with your thumb • mode to the other, remove the holding the spring (2) in place (Fig. I).
- Page 11 058-9345-0 | contact us 1-888-670-6682 Increasing Nail Depth Weather Operation Fig. L When operating any air-powered tool below freezing temperature： Turn the depth-adjustment dial (1) • clockwise (with the discharge area Verify the compressor tank have been properly drained prior to use.
- Page 12 058-9345-0 | contact us 1-888-670-6682 Maintenance Air-operated tools must be inspected periodically and worn or broken • parts must be replaced in order to keep tools operating safely and MAXIMUM SERVICE INTERVAL efficiently. TOOLS OR MAINTENANCE Inspect and replace worn or damaged O-rings, seals, etc. Tighten all...
- Page 13 058-9345-0 | contact us 1-888-670-6682 Troubleshooting PROBLEM POSSIBLE CAUSES SOLUTIONS The following chart lists common issues and solutions. Please read it The tool does The air supply is Verify that the air supply is not operate inadequate. adequate.
- Page 14 058-9345-0 | contact us 1-888-670-6682 Description Description Left orientation rubber O-ring 1.7 x 2 Right orientation rubber Spring pin Sealing ring Retainer 3 Valve seat Spring O-ring 16 x 1.6 Spring core Valve sleeve Pin C4 x 18 O-ring 6.1 x 1.8...
-
Page 15: Operating Instructions
058-9345-0 | contact us 1-888-670-6682 This MAXIMUM product is guaranteed for a period of 5 years This warranty will not apply to any parts other than original parts, from the date of original retail purchase against defects in... -
Page 16: Warranty
Maximum Canada will maintain this product and replace critical parts Neither the retailer, Maximum Canada, nor the manufacturer shall be liable for which have worn beyond reasonable use through normal use of such any other expense, loss or damage, including, without limitation, any indirect, product, any time during the first year after purchase.
Need help?
Do you have a question about the 058-9345-0 and is the answer not in the manual?
Questions and answers